Table of Contents
Advertisement
8 | Operating instructions | OBD 1110 |
• MIL ON indicates that the
Malfunction Indicator Lamp
should be ON .
• MIL OFF indicates that the
Malfunction Indicator Lamp
should be OFF .
I / M Monitors (Emissions)
Inspection / Maintenance
Monitors provide a snapshot
of the Emission System opera-
tions by indicating that the
I / M Monitors are Ready or Not
Ready . For an I / M Monitor to
be Ready, the vehicle must have
completed a drive cycle (been
driven long enough under proper
conditions to have completed a
drive cycle) . A Monitor must be
listed as Ready to pass an emis-
sions test . If an I / M Monitor is
Not Ready, it is because a drive
cycle has not completed .
The Tool will indicate Ready
(ok), Not Ready (inc), or Not
Applicable (n/a) for each I / M
Monitor . The Tool supports the
following I / M Monitors:
577383 REV A | 10.2015
Monitor
Expanded Name
Misfire Monitor
Misfire Monitor
Fuel System Mon
Fuel System Monitor
Comprehensive Compo-
Comp Component
nents Monitor
Catalyst Mon
Catalyst Monitor
Htd Catalyst
Heated Catalyst Monitor
Evaporative System Mon-
Evap System Mon
itor
Secondary Air System
Sec Air System
Monitor
Air Conditioning Refriger-
A/C Refrig Mon
ant Monitor
Oxygen Sens Mon
Oxygen Sensor Monitor
Oxygen Sensor Heater
Oxygen Sens Htr
Monitor
Exhaust Gas Recircula-
EGR/VVT Sys Mon
tion or Variable Valve Tim-
ing Monitor
Non-Methane Hydrocar-
NMHC Cat Mon
bon Catalyst
NOX Treat Mon
Nitrogen Oxide Treatment
Boost Pres Mon
Boost Pressure Monitor
Exhst Gas Sensr
Exhaust Gas Sensor
PM Filter Mon
Particulate Matter Filter
This is a complete list of I / M
Monitors supported by the Tool .
The number of Monitors read
by the Tool from your vehicle
may vary . A diesel vehicle, for
example, does not have an
Oxygen Sensor Monitor . As a
result, there will be no Oxygen
Sensor Monitor status for a die-
sel vehicle .
Two types of I / M Monitors
tests are:
Bosch Automotive Service Solutions
en
en
‰ Since DTCs Cleared - shows
status of the monitors since
the DTCs were last erased .
‰ This Drive Cycle - shows
status of monitors since the
start of the current drive
cycle . Refer to the vehicle
service manual for more
detailed information on
emission-related monitors
and their status .
9 Some vehicles do not sup-
port This Drive Cycle . If
vehicle supports both types
of monitors the I / M Monitors
Menu displays .
View Freeze Data
Displays a snapshot of operat-
ing conditions at the time the
Diagnostic Trouble Code was
created . See PID Definitions for
more information .
VIN
The VIN function allows the
tool to request the vehicle's
VIN number .
The VIN function applies to
model year 2000 and newer OBD
II compliant vehicles .
System Setup
System Setup allows:
Bosch Automotive Service Solutions
| OBD 1110 | Operating instructions | 9
• Display contrast to
be changed
• Tool information to be viewed
• Display to be checked
• Operation of the keypad to
be checked
• Memory of the Tool to
be checked
• Units of measure to
be changed
View Data
The View Data function allows
real time viewing of the vehicle's
computer module's PID data .
As the computer monitors the
vehicle, information is simultane-
ously transmitted to the Tool .
View Data allows the following
items to be viewed on the Tool:
‰ Sensor data
‰ Operation of switches
‰ Operation of solenoids
‰ Operation of relays
Multiple PIDs may be sent if vehi-
cle is equipped with more than
one computer module (for exam-
ple a powertrain control mod-
ule [PCM] and a transmission
control module [TCM] . The Tool
identifies them by their iden-
tification names (ID) assigned
by manufacturer (i .e . $10 or
$1A) . See PID Definitions for
more information .
577383 REV A | 10.2015
Hide quick links:
Advertisement
Table of Contents
