PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 1 Safety Precautions 1.1. General Guidelines · For continued safety, no modification of any circuit must be attempted. · Unplug the power cord from the power outlet before disassembling this projector. · Use correctly the supplied power cord and must ground it.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 2 Ext Option This projector has EXT OPTION in addition to standard on-screen menus. · There are SELF CHECK and TEST PATTERN for service, etc. 2.1. Procedure to enter EXT OPTION 1. Press "MENU" button on the main unit or remote control unit to display "MENU" screen, then select "OPTION" and press "ENTER"...
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 3 Self-Check Mode This mode is used to narrow down the location of the failure. 3.1. Procedure to enter the self-check mode Select "SELF CHECK" on "EXT OPTION" menu and press "ENTER" button on the main unit or remote control unit.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 3.3. Canceling the self-check mode Press "MENU" button on the main unit or remote control unit. 4 Test Pattern This projector displays seven kinds of test patterns [Horizontal lines, Vertical lines, Dots, Crosshatch, White cross, Black cross and White (No pattern)] in the four colors (White, Red, Green and Blue).
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 6 Using the SERIAL Connector The serial connector which is on the back connector panel of the projector conforms to RS-232C standard. This projector can be controlled by a PC which is connected as shown in "6.1. Connection".
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 6.4. Control commands 6.5. Communication Cable Specifications 6.6. Signal Selector Connecting Cable Specifications When connecting to a signal selector (ex. TW-SWS62J), use a cable with specifications below. Connecting method: Connects a video signal cable from the signal selector to "VIDEO IN", and an RGB signal cable to "COMPUTER 1 IN".
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 7 Disassembly Instructions Warning: · Be sure to unplug the power cord from the power outlet before disassembling this projector. Caution: · While turning over a printed circuit board, be sure to put a insulating material under it to prevent a short circuit.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 7.2. Removal of Upper Case 1. Turn the projector upside down. 2. Unscrew the 8 screws. Note: · When reassembling, confirm the interlock switch is normal status (the switch is in "ON" position). 3. Return the projector to the normal position.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA "Removal of ARF Drive Unit". 2. Unscrew the 1 scre remove the F-P.C.Board 6. Disconnect the flexible cable between G-P.C.Board and A- 7.6. Removal of G-P.C.Board P.C.Board (A20). 7. Disconnect the connector between R-P.C.Board and A- 1.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 7.11. Removal of S1-P.C.Board 1. Remove the upper case according to the section 7.2. 7.8. Removal of L-P.C.Board "Removal of Upper Case". 1. Remove the block of Analysis Block, LCD Block and 2. Open the front door.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA in the section 7.11. "Removal of S1-P.C.Board". 2. Disconnect the connector between S1-P.C.Board and S2- P.C.Board. 3. Unscrew the 2 screws and remove the S2-P.C.Board. 7. Unscrew the 2 screws and remove the exhaust fan.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Note: 12. Unscrew the 4 screws and remove the B/Q-Module. · When installing the lamp unit in the main unit, place it in a specified position and press the right and left sides of the lamp unit (arrow positions shown in the figure below), and confirm the lamp unit is inserted securely.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA panel. 7.19. Replacement of LCD Panel (B) 8. Unscrew the 3 screws and remove the block of Analysis 1. Remove the LCD block according to the section 7.18. Block, LCD Block and Projection Lens. "Removal of LCD Block".
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA shifted by your fingers. 7.20. LCD Panel Discrimination Note: ID-tag seal color LCD panel · The panel adjustment fittings set (panel attachment, LCD panel (R) panel adjuster and base plate) is an option for Blue LCD panel (B) service.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Note: · Be careful not to touch the surface of incidence polarizer. 7.24. Replacement of Projection 7.23. Replacement of Incidence Polarizer Polarizer (R and B) · The procedure is described as an example of projection 1.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 3. Loosen the 1 screw until it idles, remove the ARF unit while sliding the lock lever. 7.25. Replacement of PBS Array (Analysis Block) 1. Remove the analysis case (upper) according to the steps 1 through 3 in the section 7.23.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 8 Measurement and Adjustments 8.1. Adjustment Procedure Flowchart 8.2. Cautions for Adjustment · Never unplug the power cord until the power indicator on the projector illuminates red. · To maintain and ensure safety, always use the designated components for replacement parts.
Page 24
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Note: · See figures in the section 7.19. "Replacement of LCD Panel (B)" for 2 screws fixing the panel adjuster and 2 screws fixing the panel attachment. 2. Reassemble the projector in the reverse order of disassembling, but leave the upper case and the screws fixing the A- P.C.Board block as they are removed.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Repeat steps (1) to (3) until the green and blue crosshatch patterns merge into a cyan pattern. 8. After the adjustment, reassemble the projector according to the steps 8 through 9 in the section 7.19. "Replacement of LCD Panel (B)".
Page 26
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 8.5.3. Adjustment Procedure 8.5.3.1. Outline When the lighting area is off from the adjustment and color unevenness appears, adjust the lighting area into correct position. Symptom Measure Magenta unevenness G Reflector Adjustment Cyan unevenness R Reflector Adjustment...
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 3. Adjust the mirror adjusting lever A position to minimize color unevenness on the screen by shifting the lever in arrow directions. 4. Tighten the 1 screw. 8.5.3.3. R Reflector Adjustment 1. Turn on the power and display 100 % white pattern on the screen.
Page 28
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 8.6.3.1. Explanation of Buttons Port: Port name of PC which connects with the projector Model: Model name of projectors Data: Displays the data transmission/reception menu. Adjustment: Displays the adjustment menu. Exit: Exits this application. 8.6.4.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Set Date/Time Sets date/time of this projector adjusted with the date/time of the PC. Exit: Exits this application. 8.6.4.2. Receiving and transmitting of the data Click a target button and specify a file name. 8.6.4.3.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 8.8.2. Explanation of Buttons Executes automatic sub contrast and sub brightness adjustments, then closes this dialog. Cancel: Cancels this menu. 8.8.3. Equipment to be used PC, RGB Signal Generator, Software for Adjustment 8.8.4. Adjustment Procedure 1.
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 11 Block Diagram 11.1. Power Supply Power Supply COLD +17 V MAIN INTERLOCK F9101 POWER Q206 SWITCH Q207 POWER SWITCHING LINE LINE D9101 RECTIFIER FACTOR STB 3.4 V TRANSFORMER FILTER FILTER THERMOFUSE CORRECTION FAN 14 V...
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA 16 Replacement Parts List Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks TENC5437 POWER WIRE NET [MECHANICAL PARTS] TESA299 FRONT PANEL SPRING TEWA833 FILM IMPEDOR J0KG00000011 CLAMP CORE...
Page 73
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks TMKG814 ARF SPONGE 7 TXFEC98QEWZ ANALYSIS BLOCK TMKG815 ARF SPONGE 8 TXFEC99QEWZA OPTICAL BLOCK A TMKG823-1 POWER SPONGE 6...
Page 74
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks IC1006 C3ABQJ000048 IC1719 C0CBCBD00008 IC1007 C0DBEKG00004 IC1720 C0JBAZ002347 IC1008 C0DBEKG00004 IC1721 C0JBAZ002347 IC1009 C0DBEYY00042 IC1722 C0JBAZ002347 IC1010 C0DBEKG00004 IC1723...
Page 75
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks L1009 J0JJC0000022 EMI FILTER [DIODES] L1010 J0JCC0000168 FILTER L1012 J0JCC0000168 FILTER D1001 B0JCPD000026 DIODE L1014 J0JCC0000168 FILTER D1002 B0JCPD000026...
Page 76
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks L1722 J0JHC0000107 FILTER R1045 ERJ2GEJ220 M 22 OHM, 0.063W L3001 J0JCC0000168 FILTER R1046 ERJ3GEYJ104 M 100KOHM,J,1/16W L3002 J0JCC0000168 FILTER...
Page 77
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R1156 ERJ6ENF75R0 M 75 OHM, 1/10W R1238 ERJ3GEYJ203 RESISTOR R1158 ERJ6ENF75R0 M 75 OHM, 1/10W R1239 ERJ3GEYJ473 M 47K OHM,J,1/16W...
Page 78
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R1338 ERJ3GEY0R00 M 0 OHM, 1/16W R1446 ERJ2GEJ220 M 22 OHM, 0.063W R1339 ERJ3GEY0R00 M 0 OHM, 1/16W R1449 ERJ2GEJ472 M 4.7KOHM, 0.063W...
Page 79
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R1542 D1BZ2700A012 RESISTOR R1718 ERJ3GEYJ680 M 68 OHM,J,1/16W R1543 ERJ3GEYJ470 M 47 OHM,J,1/16W R1719 ERJ3GEYJ680 M 68 OHM,J,1/16W R1544 ERJ2GEJ101 M 100 OHM, 0.063W...
Page 80
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks R1817 ERJ2GE0R00 M 0 OHM, 0.063W R3001 ERJ2GEJ473 M 47K OHM, 0.063W R1818 ERJ2GE0R00 M 0 OHM, 0.063W R3002...
Page 81
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C1024 ECJ0EF1C104Z C 0.1UF, 16V C1108 ECJ0EF1C104Z C 0.1UF, 16V C1025 ECJ1VF1E104Z C 0.1UF, Z, 25V C1109 ECJ0EF1C104Z C 0.1UF, 16V...
Page 82
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C1184 ECJ0EF1C104Z C 0.1UF, 16V C1267 ECJ0EF1C104Z C 0.1UF, 16V C1186 ECJ2FF1C475Z CAPACITOR C1268 ECJ0EF1C104Z C 0.1UF, 16V C1187 ECJ1VF1E104Z C 0.1UF, Z, 25V...
Page 83
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C1357 ECJ1VF1C104Z C 0.1UF, Z, 16V C1462 F1G1C104A077 CAPACITOR C1358 EEEHB1E330P E 33UF, 25V C1463 F1G1C104A077 CAPACITOR C1359 EEEHB1E330P...
Page 84
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C1743 ECJ0EF1C104Z C 0.1UF, 16V C1825 ECJ1VB0J105K C 1UF,Z, 6.3V C1745 ECJ0EF1C104Z C 0.1UF, 16V C1826 ECJ1VB0J105K C 1UF,Z, 6.3V...
Page 85
PT-FW100NTU / PT-FW100NTE / PT-FW100NTEA Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C3021 ECJ2FF1A106Z C 10UF, 10V JS1010 ERJ6GEY0R00 M 0 OHM,J,1/10W C3022 ECJ1VF1A105Z C 1UF, Z, 50V LF9101 G0B692J00001 FILTER...