SDR-S26P CONTENTS Page Page 1 Safety Precaution 9.1. EEPROM Data for spare parts of the SUB P.C.B. 1.1. General Guidelines 9.2. Service Positions 2 Warning 9.3. Location for Connectors of the Main P.C.B. and Sub 2.1. Prevention of Electrostatic Discharge (ESD) to P.C.B.
SDR-S26P 1 Safety Precaution 1.1. General Guidelines 1. IMPORTANT SAFETY NOTICE There are special components used in this equipment which are important for safety. These parts are marked by in the Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturer’s specified parts to prevent X-RADIATION, shock fire, or other hazards.
SDR-S26P 2 Warning 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semiconductor “chip”...
SDR-S26P 2.2. Service caution based on legal restrictions 2.2.1. General description about Lead Free Solder (PbF) The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this equipment in considering the globally environmental conservation.
SDR-S26P 2.3. Caution for AC Cord Blue Neutral (For EB/GC9) Brown Live As the colours of the wires in the mains lead of this appliance 2.3.1. Information for your safety may not correspond with the coloured markings identifying the IMPORTANT...
2. Remove the Lithium Battery “ML-614S/ZTE” and then replace the new one. (See .) Fig. B1 Note: The lithium battery is a critical component. (Type No.: ML-614S/ZTE Manufactured by Panasonic.) It must never be subjected to excessive heat or discharge. It must therefore only be fitted in equipment designed specifically for its use.
2. Parts List for individual parts of Main P.C.B. and Sub P.C.B. 2) The following category are recycle module part. Please send them to Central Repair Center. *Main P.C.B. (LSEP8462G1: SDR-S26GT/P/PC/PR/PU) (LSEP8462U1: SDR-S26EG/EB/EP/EF/EC/EE/GC9/GN/GJ/GK) *Sub P.C.B. (LSEP8474A1: SDR-S26P/PC/PR/PU) (LSEP8474C1: SDR-S26GT) (LSEP8474P1: SDR-S26EE/GC9/GJ/GK/GN) (LSEP8474R1: SDR-S26EB/EC/EF/EG/EP) When a part replacement is required for repairing each Main P.C.B.
SDR-S26P 5 Location of Controls and Components Followings are the Location of Controls and Components for SDR-H80P/PC, H90P/PC as a sample. For other models, refer to each Operating Instructions.
SDR-S26P 6 Service Mode 6.1. Service Menu When abnormal detection contents are confirmed, do the following operation. Automatic diagnosis code will bedisplayed. (Service Menu) To enter the Service Menu 1. Turn the Power on and set the Mode Dial to [VIDEO RECORDING MODE].
SDR-S26P 6.2. About Default Setting The data of Menu, Mode, Card and EEPROM setting, etc. is set to the default condition in factory. 6.2.1. How to set the Default Setting 1. Turn the Power on and set the Mode Dial to [VIDEO RECORDING MODE].
SDR-S26P 8 Disassembly and Assembly Instructions 8.1. Disassembly Flow Chart This flow chart indicates the disassembly steps the cabinet parts and P.C.B.. Unit in order to access to be serviced. When reinstalling, perform the steps in the reverse order. 8.2.
Page 20
SDR-S26P 1) How to Remove How to remove 1. Slide Top/ Operation unit by approx. 3mm to unlock 1. Unlock the locking portions from the Dowels. Tabs A not to damage FPC 2. Unlock Tabs B. 3. Unlock FP61. Fig. D5 How to remove 1.
Page 21
SDR-S26P Fig. D7 How to remove 1. Remove Projections from Side R/ LCD Unit. Fig. D9 How to remove 1. Remove 2 screws (L). 2. Unlock Connector B9001 from B9002 to remove Main P.C.B. Fig. D8 Fig. D10...
SDR-S26P 8.4. Disassembly Procedures of Camera Lens Unit The following flowchart describes order or steps for removing the Camera lens unit and certain printed circuit boards in order to make access to the item needing service. To reassemble the unit follow the steps in reverse order.
SDR-S26P 9 Measurements and Adjustments 9.1. EEPROM Data for spare parts of the SUB P.C.B. After replacing the SUB P.C.B., be sure to achieve adjustment. As for Adjustment condition/procedure, consult the “Adjustment Manual” which is available in Adjustment software. The Adjustment software is available at “TSN Website”, therefore, access to “TSN Website” at “Support Information from NWBG/VDBG-PAVC”.
Page 25
SDR-S26P 9.2.2. Checking and repairing individual circuit boards except module parts (Main P.C.B. and Sub P.C.B.) How to use extension cables.
SDR-S26P 9.4. Electrical Adjustment Procedures 9.4.1. Initial Guideline The table below shows which adjustments are necessary according to the unit parts and individual parts to be replaced. Make sure to perform these adjustments shown below as necessary. 9.4.2. Set-up manual for SD Card/Hard Disk Video Camera.
Page 29
SDR-S26P c. Connect the PC and SD Card/Hard Disk Video Camera as shown in Fig. E1 and E2. Fig. E1 Fig. E2 Rough image of set-up connection...
Page 30
SDR-S26P 9.4.3. Set up of PC-EVR Adjustment Program 1. Turn on the PC and install the PC-EVR Adjustment Program into the PC. 2. Execute the "khd2009.exe" file by double clicking to start up the PC-EVR Adjustment Program. The main menu will be displayed.
Page 31
SDR-S26P 9.4.4. How to confirm "OneNAND-Flash 4. Confirm the OneNAND-Flash ROM Error information. ROM Error" If there is a problem with Flash ROM (IC3203), the unit does not turn the power on. (Problem: When the power SW is turned on, the power LED lights for 3 seconds and goes out.
SDR-S26P 10 Maintenance 10.1. Cleaning Lens and LCD Panel Do not touch the surface of the lens and LCD Panel with your hand. When cleaning the lens, use air-Blower to blow off the dust. When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the their surface.
SDR-S26P 11.2. INTERCONNECTION SCHEMATIC DIAGRAM LENS UNIT ECM(L) ECM(R) FP41 ECM_R ECM_R MIC_GND MIC_GND ECM_L ECM_L MIC UNIT MAIN P.C.B. LENS DRIVE VIDEO AVIO TG/AFE RESIZE SPOUT1 SPEAKER MEMORY USB HOST SPOUT2 SUB POWER MAIN CONNECTION SPEAKER UNIT OPEN/CLOSE SUB P.C.B.
SDR-S26P 11.5. LCD SHAFT FPC SCHEMATIC DIAGRAM (LCD SHAFT FPC) : VIDEO MAIN SIGNAL PATH "FOR REFERENCE ONLY" LCD REVERS : VIDEO MAIN SIGNAL PATH IN REC MODE TO MAIN CN LCD_RVS TO LCD BL D_GND D_GND D_GND D_GND D_GND...
SDR-S26P 13.2. Replacement Parts List E.S.D. standards for Electrostatically Sensitive Devices, refer Ref. No. Part No. Part Name & Remarks Description to PREVENTION OF ELECTROSTATIC DISCHARGE (ESD) ELECTROSTATICALLY SENSITIVE (ES) DEVICES LSYK2620 SIDE R/SHAFT PR,PCR,PRR,PU section. UNIT LSYK2625 SIDE R/SHAFT...
SDR-S26P 13.2.3. Camera Lens Section Parts List Ref. No. Part No. Part Name & Remarks Description XQN16+BF3FN SCREW XQN16+BF3FN SCREW XQN16+BJ5FJK SCREW XQN16+BJ5FJK SCREW XQN16+BJ5FJK SCREW Ref. No. Part No. Part Name & Remarks Description LSXN0057 LENS UNIT 13.2.2. LCD Section Parts List...
SDR-S26P Ref. No. Part No. Part Name & Remarks Ref. No. Part No. Part Name & Remarks Description Description LSQT1499-A VQL1U89 COLOR LABEL GTA,EGA,ECA,E (PORTUGUESE/SPAN BA,GJA, ISH) GNA,EPA,GC9A, LSQT1553-A O/I (FINNISH) GKA,EEA LSQT1500-A VQL1R91 COLOR LABEL (SWEDISH/DANISH) VQL1Z36 COLOR LABEL...
Page 52
SDR-S26P Ref. No. Part No. Part Name & Remarks Ref. No. Part No. Part Name & Remarks Description Description R6310 ERJ3GEYJ330 M.RESISTOR CH 1/10W 33 R8101 ERJ3GEY0R00 M.RESISTOR CH R6311 ERJ3GEYJ330 M.RESISTOR CH 1/10W 0 1/10W 33 R8102 ERJ3GEY0R00 M.RESISTOR CH...