Epson TM-L90 Manufacturing Manual
Tm-l90 series
Hide thumbs
Also See for TM-L90:
- Technical reference manual (212 pages) ,
- Service manual (148 pages) ,
- Developer's manual (140 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Epson TM-L90
Summary of Contents for Epson TM-L90
- Page 1 Confidential TM-L90 Roll Paper Manufacturing Guide STANDARD Rev. No. Notes Copied Date Copied by SEIKO EPSON CORPORATION MATSUMOTO MINAMI PLANT 2070 KOTOBUKI KOAKA, MATSUMOTO-SHI, NAGANO, 399-8702 JAPAN PHONE(0263)86-5353 FAX(0263)86-9925...
- Page 2 Before reading this guide, be sure you have the correct version of each page. Revisions Design Section Sheet Rev. No. Rev. Document Sheet Rev. Sheet Rev. Sheet Rev. − Enactment Tsukada Takizawa TITLE Front Part Rev. General Table of TM-L90 Roll Paper Descriptions Cover Sheet Scope Contents Contents Appendix Total Manufacturing Guide...
- Page 3 2. On the earlier of (a) termination of your relationship with Seiko Epson, or (b) Seiko Epson’s request, you must stop using the confidential information. You must then return or destroy the information, as directed by Seiko Epson.
-
Page 4: Table Of Contents
A.2 Notes on Storage.........................15 A.3 Notes on Two-Color Paper Handling...................15 APPENDIX B. MAINTENANCE......................16 B.1 Cleaning the Autocutter .......................16 B.2 Cleaning the Platen ........................17 APPENDIX C. ROLL PAPER TYPE NO....................18 SHEET TITLE REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 5: Requirements For Roll Paper
Outside roll paper diameter: Maximum 90 mm {3.54"} (*) Using roll paper with an inside diameter of 25.4 mm {1"} or less may decrease the detection accuracy of the roll paper near-end sensor. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 6: Receipt Roll Paper
Print density can be set with a software command. Original paper no. Density level P350 KF50 TF60KS-E, TF50KS-E, PD750R 100% PD160R, TF11KS-ET 105% TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 7: Paper To Use For High Speed
Paper feeding Preprintable area direction 40 ~ 300 or more 4 ~ 7.5 (Units: mm) Back (non-printing side) Black Mark Interval Requirement TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 8: Die-Cut Label Roll Paper
Thickness: 9 ~ 21 µm Peeling strength (against backing paper) 0.098 N/25 mm or more (JIS Z0237) Backing paper (separation paper) Thickness: 41 ~ 71 µm Die-Cut Label Paper Thickness Requirements TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 9: Requirements For Die-Cut Label Size
If (L –L ) is less than 3.6 mm or the label length is less than 25.4 mm, the paper may be fed wastefully because action 4 is not performed. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 10: Automatic Paper Layout Setup
6) The printer measures the paper layout settings of the paper inserted automatically and stores them in the NV memory. 7) Once the automatic paper layout setting is performed, the automatic paper layout setting mode is ended. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... - Page 11 (Printable area) Cutting position Label interval L 1: 30.4 ~ 106.6 Paper feeding direction 2.8 or more Face stock [Units: mm] (printing face) Parameters for Setting up Automatic Paper Layout TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide...
-
Page 12: Manual Paper Layout Setup
The transparency rates are calculated as follows: Density = Log (Amount of irradiation / Amount of transparency) Then, Transparency rate (%) = (Amount of transparency / Amount of irradiation) × 100 TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 13: Requirements For Black Mark Position For Die-Cut Label Paper
For die-cut labels with black marks, there are two reflective rate requirements, depending on the size and position of black marks. Be sure to use label paper that meets either black mark position requirement I or II as follows: TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 14: Requirements For Black Mark Position I
4 ~ 7.5 position 15 or more 0 ~ 1 Paper feeding direction [Units: mm] Preprintable area Back (non-printing side) NOTE: Reflective rates are measured by the Macbeth PCM-II (Filter D) meter. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 15: Requirements For Black Mark Position Ii
(The dotted lines indicate the position of the label.) Preprintable area Back (non-printing side) [Units: mm] The black mark is in the position between labels, but does not cover the entire interval. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 16: Continuous Label Roll Paper
Rubber type • Silicon type • Other special adhesive agents If an original paper other than that specified is used, be sure to confirm the specifications of the original paper. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 17: Requirements For Size Of Continuous Label Paper
(b): 0.3 mm {0.12"} or more to prevent the adhesive agent of the label roll paper from being attached to the platen.) TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 18: Reliability
1,000,000 cuts (for die-cut labels, baking paper is cut) When cutting continuous label paper: 500,000 cuts (1,000,000 cuts with cutter blade cleaning) The values above are for when the specified paper is used. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 19: Appendix A. Notes On Paper Handling
(customized value) and using two-color paper as the print paper. • In two-color printing, the hue might not be clear, depending on printing patterns. • The reliability of two-color paper differs from that of single-color paper. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 20: Appendix B. Maintenance
It is recommended not to use an alcohol solvent. If an alcohol solvent is used, the adhesive agent might begin to be dissolved, which can reduce the efficiency of the printer. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 21: Cleaning The Platen
1) Turn off the printer and open the paper roll cover. 2) Clean the thermal element of the print head with a cotton swab moistened with water. 3) After moisture dries out completely, turn on the printer. TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide... -
Page 22: Appendix C. Roll Paper Type No
1310 BR21 label paper {1"} 080090025 060090025 038090025 51 mm ENTLB ENTLB BR21 {2"} 080090051 060090051 76 mm ENTLB ENTLB BR21 {3"} 080090076 060090076 ENTLB ENTLB BR21 080090102 060090102 {4"} TITLE SHEET REVISION TM-L90 Roll Paper NEXT SHEET Manufacturing Guide...