Page 1
DATA SHEET TDA8002C IC card interface Product specification Supersedes data of 1999 Feb 24 File under Integrated Circuits, IC02 INTEGRATED CIRCUITS 1999 Oct 12...
Page 2
Pay TV Road tolling. GENERAL DESCRIPTION The TDA8002C is a complete low-power analog interface for asynchronous and synchronous cards. It can be placed between the card and the microcontroller. It performs all supply, protection and control functions. It is directly compatible with ISO 7816, GSM11.11 and EMV...
Page 3
Philips Semiconductors IC card interface QUICK REFERENCE DATA SYMBOL PARAMETER Supplies supply voltage supply current DD(lp) supply current DD(idle) supply current DD(active) Card supply output voltage CC(O) General card clock frequency deactivation sequence duration continuous total power dissipation TDA8002CT/x TDA8002CG...
Philips Semiconductors IC card interface BLOCK DIAGRAM V DDD handbook, full pagewidth 100 nF ALARM VOLTAGE SENSE ALARM RSTIN CMDVCC MODE CV/TV LATCH CLKDIV1 CLKDIV2 CLKSEL STROBE CLKOUT XTAL1 XTAL2 AUX1UC TDA8002CG AUX2UC I/OUC 1999 Oct 12 V DDA 100 nF...
Page 5
Philips Semiconductors IC card interface PINNING SYMBOL TYPE TYPE TYPE CT/A CT/B CT/C XTAL1 XTAL2 I/OUC AUX1UC AUX2UC ALARM CLKSEL CLKDIV1 CLKDIV2 STROBE CLKOUT DGND1 AGND AUX2 PRES PRES CV/TV AUX1 CMDVCC RSTIN 1999 Oct 12 TYPE crystal connection or input for external clock...
Page 6
Philips Semiconductors IC card interface SYMBOL TYPE TYPE TYPE CT/A CT/B CT/C MODE DGND2 Note 1. A pull-up resistor of 100 k connected to V handbook, halfpage XTAL1 XTAL2 I/OUC AUX1UC AUX2UC ALARM CLKSEL TDA8002CT/A CLKDIV1 CLKDIV2 STROBE CLKOUT DGND1...
When V falls below V and a deactivation sequence of the contacts is performed. 1999 Oct 12 Clock circuitry The TDA8002C supports both synchronous and asynchronous cards. There are three methods to clock the , AGND, circuitry: (i.e. V...
Page 9
Philips Semiconductors IC card interface handbook, full pagewidth V DD ALARM Fig.6 ALARM as a function of V handbook, full pagewidth OFF, I/OUC AUX1UC, AUX2UC INPUTS 1999 Oct 12 pulse width minimum of 10 ms). t SL t IS t SI Fig.7 Chip select.
Page 10
Philips Semiconductors IC card interface Table 1 Clock circuitry definition MODE CLKSEL HIGH HIGH HIGH HIGH HIGH HIGH Notes 1. X = don’t care. 2. In low-power mode. 3. f = 32 kHz in low-power mode. I/O circuitry The three I/O transceivers are identical. The state is HIGH for all I/O pins (i.e.
Page 11
Internal oscillator is slowed to 32 kHz, providing 16 kHz on CLKOUT. CTIVE MODE When the activation sequence is completed, the TDA8002C will be in the active mode. Data is exchanged between the card and the microcontroller via the I/O lines. ACTIVATION POWER...
Page 12
Philips Semiconductors IC card interface CTIVATION SEQUENCE From Idle mode, the circuit enters the activation mode when the microcontroller sets the CMDVCC line LOW or sets the MODE line HIGH when the CMDVCC line is already LOW. The internal circuitry is then activated, the internal clock is activated and an activation sequence is executed.
Page 13
Philips Semiconductors IC card interface handbook, full pagewidth OSC_INT/64 CLKDIV1 CLKDIV2 CMDVCC V CC RSTIN Fig.11 Activation sequence using CMDVCC, CLKDIV1 and CLKDIV2 signals to enable CLK. handbook, full pagewidth CMDVCC V CC AUX1UC AUX1 RSTIN t act STROBE Fig.12 Activation sequence for synchronous application.
Page 14
Philips Semiconductors IC card interface EACTIVATION SEQUENCE When a session is completed, the microcontroller sets the CMDVCC line to HIGH state or MODE line to LOW state. The circuit then executes an automatic deactivation sequence by counting the sequencer down and thus end in the Idle mode.
Page 15
Philips Semiconductors IC card interface Fault detection The following fault conditions are monitored by the circuit: Short-circuit or high current on V Removing card during transaction dropping Overheating. handbook, full pagewidth OSC_INT/64 PRES V CC 1999 Oct 12 When one or more of these faults are detected, the circuit pulls the interrupt line OFF to its active LOW state and a deactivation sequence is initiated.
Page 16
Philips Semiconductors IC card interface LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134); note 1. SYMBOL PARAMETER digital supply voltage analog supply voltage card supply voltage pins; XTAL1, XTAL2, ALARM, CS, MODE, RSTIN, CLKSEL, AUX2UC, AUX1UC,...
Page 17
Philips Semiconductors IC card interface CHARACTERISTICS = 3.3 V; T = 25 C; f = 10 MHz; unless otherwise specified. xtal SYMBOL PARAMETER Supplies supply voltage supply current DD(lp) supply current DD(idle) supply current DD(active) threshold voltage on V voltage supervisor...
Page 18
Philips Semiconductors IC card interface SYMBOL PARAMETER Data lines ENERAL delay between falling edge d(edge) of I/O, AUX1, AUX2, I/OUC, AUX1UC and AUX2UC rise and fall times maximum frequency on I/O(max) data lines I/O, AUX1 AUX2 ( ATA LINES output voltage...
Page 19
Philips Semiconductors IC card interface SYMBOL PARAMETER LOW-level output voltage on OL(OFF) pin OFF LOW-level output current on OL(ALARM) pin ALARM HIGH-level output voltage OH(ALARM) on pin ALARM ALARM pulse width Clock output (CLKOUT; powered from V frequency on CLKOUT...
Page 20
Philips Semiconductors IC card interface SYMBOL PARAMETER (CV/TV CS) (I OGIC INPUTS LOW-level input voltage HIGH-level input voltage Logic inputs PRES and PRES; note 5 LOW-level input voltage HIGH-level input voltage LOW-level input current on IL(PRES) pin PRES HIGH-level input current on...
Page 21
Philips Semiconductors IC card interface Notes 1. It may be necessary to connect capacitors from XTAL1 and XTAL2 to ground depending on the choice of crystal or resonator. 2. When the oscillator is stopped in mode 1, XTAL1 is set to HIGH.
Page 22
CARD READ 470 nF 100 nF 470 nF TDA8002C should be placed as close as possible to the card reader. (1) Contact normally open. (2) C3 close to pin V of TDA8002C. (3) C4 close to C1 contact of card reader.
Page 23
CMDVCC 100 nF CARD READ 100 nF TDA8002C should be placed as close as possible to the card reader. (1) Contact normally open. (2) C3 close to pin V of TDA8002C. (3) C4 close to C1 contact of card reader.
Philips Semiconductors IC card interface PACKAGE OUTLINES SO28: plastic small outline package; 28 leads; body width 7.5 mm pin 1 index DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT max. 0.30 2.45 2.65 0.25 0.10 2.25 0.012 0.096...
Page 25
Philips Semiconductors IC card interface LQFP32: plastic low profile quad flat package; 32 leads; body 5 x 5 x 1.4 mm pin 1 index DIMENSIONS (mm are the original dimensions) UNIT max. 0.15 1.60 0.25 0.05 Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
Page 26
Philips Semiconductors IC card interface SOLDERING Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages”...
Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.