Side Panel L And Control Cover Removal; Connecting Cable To Control Board Connector; Side Panel L And Control Cover Installation; Function Setting - Fujitsu AGYG09LVCA Installation Manual

1

11.4. Side panel L and control cover removal

(1) Refer to "6.3. Side panel L, R removal and installation" to remove the side panel L.
(2) Remove the control cover.
(3) Remove the control inner cover.
Control
inner cover
Control cover
]
1

11.5. Connecting cable to control board connector

(1) Connect the cable the circuit board and hang on the hooks.
CN 20 CN 14
(EX. OUT1) (EX. IN1)
CN 6
(2) Install the control cover.
(3) Use cable clamper and screw to fasten the cord of wired remote controller.
(4) Fix the binder clamp with the screw and bind the cable of external kit with the binder.
Earth
(Ground)
wire
Screw
Cable
Hook
Cable
clump
Screw
] 1

11.6. Side panel L and control cover installation

Install Side panel L and control cover by the reverse procedures as stated in "11.4. Side
panel L and control cover removal".
AMP Air Conditioning
PCB
Connector
Option type
Wired remote controller
Simple remote controller
External input
(EX. IN1)
External output
(EX. OUT1)
PCB
Binder clamp

12. FUNCTION SETTING

Perform the "FUNCTION SETTING" according to the installation conditions using the
remote controller.
Confi rm whether the wiring work for Outdoor unit or Branch box has been fi nished.
Confi rm that the cover for the electrical enclosure on the outdoor unit is in place.
• This procedure changes to the function settings used to control the indoor unit
according to the installation conditions. Incorrect settings can cause the indoor unit to
malfunction.
• After the power is turned on, perform the "FUNCTION SETTING" according to the
installation conditions using the remote controller.
• The settings may be selected between the following two: Function Number or Setting
Value.
• Settings will not be changed if invalid numbers or setting values are selected.
• Refer to the installation manual enclosed with the remote control unit when the wired
remote control unit (option) is used.
Entering the Function Setting Mode
While pressing the FAN button and SET TEMP. (
button to enter the function setting mode.
STEP 1
Selecting the Remote Controller Signal Code
Use the following steps to select the signal code of the
No.
remote controller. (Note that the air conditioner cannot
receive a signal code if the air conditioner has not been set
CN 6
for the signal code.)
The signal codes that are set through this process are
CN 14
applicable only to the signals in the FUNCTION SETTING.
For details on how to set the signal codes through the normal
CN 20
process, refer to Remote controller signal code.
(1) Press SET TEMP. (
code between
display to the air conditioner signal code. (initially set to
If the signal code does not need to be selected, press the
MODE button and proceed to STEP 2.)
(2) Press the TIMER MODE button and check that the indoor
unit can receive signals at the displayed signal code.
(3) Press the MODE button to accept the signal code, and
proceed to STEP 2.
The air conditioner signal code is set to A prior to shipment.
Contact your retailer to change the signal code.
The remote controller resets to signal code A when the batteries in the remote
controller are replaced. If you use a signal code other than signal code A, reset the
signal code after replacing the batteries.
If you do not know the air conditioner signal code setting, try each of the signal codes
( ) until you fi nd the code which operates the air conditioner.
Binder
STEP 2
Selecting the Function Number and Setting Value
(1) Press the SET TEMP. (
select the function number. (Press the MODE
button to switch between the left and right
digits.)
(2) Press the FAN button to proceed to setting the
Screw
value. (Press the FAN button again to return to
the function number selection.)
(3) Press the SET TEMP. (
select the setting value. (Press the MODE
button to switch between the left and right
digits.)
(4) Press the TIMER MODE button, and START/
STOP button, in the order listed to confi rm the
settings.
(5) Press the RESET button to cancel the function
setting mode.
(6) After completing the FUNCTION SETTING, be
sure to turn off the power and turn it on again.
www.ampair.co.uk | sales@ampair.co.uk
CAUTION
) simultaneously, press the RESET
) ( ) button to change the signal
. Match the code on the
)
) ( ) buttons to
Function number
) ( ) buttons to
Setting
value
En-8