Advertisement
Connecting the Units
Connecting the system
RCA cable (supplied)
Blue
This product
Black
Blue
3 m
Display with RCA
IP-BUS cable
input jacks
(supplied with
the TV tuner)
To audio
To video
inputs
input
RCA cables
Black
Blue
(sold separately)
Hide-away TV tuner
(e.g. GEX-P7000TVP)
(sold separately)
Yellow
Green
Right (Red)
Left (White)
Green
Yellow
Right (Red)
20 pin cable
(supplied with the display)
Left (White)
Rear video output
(REAR VIDEO OUTPUT)
(Yellow)
Left
(White)
Subwoofer output or non fading
output (SUBWOOFER OUTPUT
or NON-FADING OUTPUT)
Blue
IP-BUS cable (supplied)
3 m
Right (Red)
Left (White)
Optical cable (supplied)
Front video output
Black
(FRONT VIDEO
OUTPUT)
(Yellow)
3 m
Multi-CD player
(sold separately)
FM MODULATOR
IP-BUS MAIN UNIT
RCA cable
IP-BUS AV MASTER
(supplied with
the head unit)
Not used.
Video input
(VIDEO INPUT)
(Yellow)
Installation
<ENGLISH>
Note:
•
Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect-
ed up properly, and the unit and the system work
properly.
•
Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.
Right (Red)
•
Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
Rear audio output
tions of the vehicle.
(DVD REAR MONITOR
•
Install the unit where it does not get in the dri-
OUTPUT)
ver's way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.
•
When mounting this unit, make sure none of the
leads are trapped between this unit and the sur-
rounding metalwork or fittings.
•
Do not mount this unit near the heater outlet,
where it would be affected by heat, or near the
doors, where rainwater might splash onto it.
•
Before drilling any mounting holes always check
behind where you want to drill the holes. Do not
drill into the gas line, brake line, electrical wiring
or other important parts.
•
If this unit is installed in the passenger compart-
Head unit
ment, anchor it securely so it does not break free
(e.g. DVH-P7050)
while the car is moving, and cause injury or an
(sold separately)
accident.
•
If this unit is installed under a front seat, make
sure it does not obstruct seat movement. Route
all leads and cords carefully around the sliding
mechanism so they do not get caught or pinched
in the mechanism and cause a short circuit.
AV system display
(e.g. AVX-7300)
(sold separately)
Red
Installing the unit
Routing the optical cable
Mounting with brackets
Precaution:
•
Try not to bend the optical cable sharply. If it is
necessary to bend it sharply, make sure that the
bending radius is at least 25 mm, otherwise the
cable will not transfer signals properly and so
this unit will not work properly.
Tapping screw (4 × 12 mm)
•
Route the optical cable so that nothing heavy
rests on it, and so that it cannot be stepped on or
caught in anything – for instance, a door.
•
Make a loop of diameter at least 200 mm with
the remaining optical cable so that the cable does
Screw
(4 × 8 mm)
not get strained.
•
When plugging the optical cable into the unit,
use the supplied cable clamps to prevent the
cable from being bent sharply.
•
Route the optical cable so that it does not get
Bracket
Car mat or chassis
caught in moving parts such as the gear shift,
hand brake, or seat sliding mechanism. Keep the
Drill 2 to 2.5 mm diameter holes.
cable away from hot spots, such as near the
heater outlet.
Using the corrugated tube
Mounting with velcro tape
To prevent the optical cable from being strained,
Thoroughly wipe off the surface before affixing
use the corrugated tube after cutting it to the cor-
the velcro tape.
rect length.
• Insert the optical cable into the cor-
rugated tube.
Optical cable
Velcro tape
Corrugated tube
Car mat or chassis
<ENGLISH>
Mounting the clamp
The clamp is used to secure the optical cable
when using it. The other clamp is installed on the
back side of the head unit similarly and used to
secure the optical cable.
1. Insert the clamp in the direction
indicated in the figure, and turn it 90
degrees to lock.
Clamp
2. Secure the optical cable.
Optical cable
Advertisement
