Table of Contents
Advertisement
Quick Links
SERVICE MANUAL
Ver. 1.0 2007.01
• The tuner and CD sections have no adjustments.
CD Player section
Signal-to-noise ratio:
120 dB
Frequency response:
10 – 20,000 Hz
Wow and flutter:
Below measurable limit
Tuner section
FM
Tuning range:
87.5 – 108.0 MHz
Antenna (aerial) terminal: External antenna (aerial) connector
Intermediate frequency:
10.7 MHz/450 kHz
Usable sensitivity:
9 dBf
Selectivity:
75 dB at 400 kHz
Signal-to-noise ratio:
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz:
0.5 % (stereo), 0.3 % (mono)
Separation:
35 dB at 1 kHz
Frequency response:
30 – 15,000 Hz
MW/LW
Tuning range:
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna (aerial) terminal: External antenn (aerial) connector
Intermediate frequency:
10.7 MHz/450 kHz
Sensitivity:
MW: 30 µV, LW: 40 µV
Power amplifier section
Outputs:
Speaker outputs (sure seal connectors)
Speaker impedance:
4 – 8 ohms
Maximum power output: 50 W × 4 (at 4 ohms)
Sony Corporation
9-887-537-01
eVehicle Division
2007A04-1
Published by Sony Techno Create Corporation
© 2007.01
CDX-A360
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
General
Outputs:
Inputs:
Tone controls:
Power requirements:
Dimensions:
Mounting dimensions:
Mass:
Supplied accessories:
Design and specifications are subject to change
without notice.
US and foreign patents licensed form Dolby
Laboratories.
FM/MW/LW COMPACT DISC PLAYER
AEP Model
UK Model
CDX-A250/A250EE
MG-611WA-186//Q
KSS1000E
Audio outputs terminal (sub/rear switchable)
Power antenna (aerial) relay control terminal
Power amplifier control terminal
Telephone ATT control terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
12 V DC car battery (negative ground (earth))
Approx. 178 × 50 × 178 mm
(w/h/d)
Approx. 182 × 53 × 162 mm
(w/h/d)
Approx. 1.2 kg
Parts for installation and connections (1 set)
Card remote commander: RM-X151
Advertisement
Table of Contents
Related Manuals for Sony CDX-A360
Summary of Contents for Sony CDX-A360
- Page 1 Outputs: Speaker outputs (sure seal connectors) Speaker impedance: 4 – 8 ohms Maximum power output: 50 W × 4 (at 4 ohms) FM/MW/LW COMPACT DISC PLAYER Sony Corporation 9-887-537-01 eVehicle Division 2007A04-1 Published by Sony Techno Create Corporation © 2007.01...
- Page 2 COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
-
Page 3: Table Of Contents
CDX-A360 • CD Playback TABLE OF CONTENTS You can play CD-DA (also containing CD TEXT*), CD-R/CD- RW (MP3/WMA files also containing Multi Session) and ATRAC SERVICE NOTE ............4 CD (ATRAC3 and ATRAC3plus format). GENERAL Type of discs Label on the disc Location of Controls and Basic Operations .... -
Page 4: Service Note
CDX-A360 SECTION 1 SERVICE NOTE EXTENSION CABLE AND SERVICE POSITION When repairing or servicing this set, connect the jig (extension cable) as shown below. • Connect the MAIN board (CNP301) and the SERVO board (CN2) with the extension cable (Part No. J-2502-076-1). -
Page 5: General
CDX-A360 SECTION 2 GENERAL This section is extracted from instruction manual. • LOCATION OF CONTROLS AND BASIC OPERATIONS Location of controls and basic operations Main unit E SEEK –/+ buttons The following buttons on the card remote commander have also different buttons/functions To skip tracks (press);... - Page 6 CDX-A360 Note for the antenna (aerial) connecting Hinweis zum Anschließen der Antenne Remarque sur le raccordement de Nota per il collegamento dell’antenna Opmerking bij de antenne-aansluiting If your car antenna (aerial) is an Wenn Ihre Autoantenne der ISO-Norm l’antenne Se l’antenna dell’auto è di tipo...
-
Page 7: Disassembly
CDX-A360 SECTION 3 DISASSEMBLY Note: This set can be disassemble according to the following sequence. 3-1. SUB PANEL ASSY (Page 8) 3-2. CD MECHANISM BLOCK (Page 8) 3-10. SERVO BOARD 3-3. MAIN BOARD 3-4. CHASSIS (T) SUB ASSY (Page 12) -
Page 8: Sub Panel Assy
CDX-A360 Note: Follow the disassembly procedure in the numerical order given. 3-1. SUB PANEL ASSY 3 two claws 2 two claws 1 two screws (+PTT 2.6 × 6) 4 sub panel assy 3-2. CD MECHANISM BLOCK 6 bracket (CD) 7 CD mechanism block 5 two screws (+PTT 2.6 ×... -
Page 9: Main Board
CDX-A360 3-3. MAIN BOARD 2 two screws (+PTT 2.6 × 8) 4 two screws (+P 2.6 × 8) 5 two screws (+PTT 2.6 × 10) 1 three screws 6 screw (+BTT 2.6 × 5) (+P 2.6 × 10) 7 screw (+PTT 2.6 ×... -
Page 10: Roller Arm Assy
CDX-A360 3-5. ROLLER ARM ASSY 3 washer 5 roller arm assy 4 gear (RA1) 2 spring (RAR-B) 1 spring (RAL-B) 3-6. CHASSIS (OP) ASSY 0 chassis (OP) assy 9 coil spring (damper) (green) lever (D) 1 optical pick-up (16 core) -
Page 11: Optical Pick-Up
CDX-A360 3-7. OPTICAL PICK-UP 2 chucking arm sub assy 5 claw 1 tension coil spring (CHKG) 7 optical pick-up 6 main shaft 4 rack (SL) 3 screw (+B 1.4 × 5) 3-8. SL MOTOR ASSY (M902) 1 screw (+P 1.4 × 1.8) -
Page 12: Le Motor Assy (M903)
CDX-A360 3-9. LE MOTOR ASSY (M903) 7 screw 9 gear (LE-B) assy (+M 1.7 × 2.5) 8 bearing (LEB-N) 0 screw (+M 1.7 × 2.5) qd two toothed lock screws 2 gear (LE1) (+M 1.4 ) lever (D) bracket (LEM-N) -
Page 13: Diagnosis Function
CDX-A360 SECTION 4 DIAGNOSIS FUNCTION Description of the Diagnostics function: 4. Contents of each display mode 4-1. Reset count display mode 1. Setting the Diag display mode With the power off, press the [4/SHUF] button, [5] button, and [4/SHUF] button on the set body or the remote control (for more than 2 seconds) in turn. - Page 14 CDX-A360 4-5. CD error information display mode 4-6. OFFSET/FAILURE error display mode 4-5-1. Error description 0 6 1 X X X X X 0 5 1 Operating hours Error information Error description Error description Indication Description (in hexadecimal (0: OFFSET, 1: FAILURE)
-
Page 15: Diagrams
CDX-A360 SECTION 5 DIAGRAMS 5-1. BLOCK DIAGRAM — CD SECTION — • R-ch is omitted due to same as L-ch. • Signal Path : CD PLAY DETECTOR MAIN FPI2 RFEQO 81 RFI 88 AGCI CD-L SECTION 82 RFRPI (Page 16) -
Page 16: Block Diagram -Main Section
CDX-A360 5-2. BLOCK DIAGRAM — MAIN SECTION — ELECTRONIC VOLUME IC401 (Page 15) CD-L 9 CD LCH J330 SECTION OUT SUB-L REAR R-CH 8 CD RCH OUT SUB-R R-CH AUDIO OUT R-CH R-CH J901 5 AUX LCH IC2-BUS 3 AUX RCH... -
Page 17: Block Diagram -Display Section
CDX-A360 5-3. BLOCK DIAGRAM — DISPLAY SECTION — 5-4. CIRCUIT BOARDS LOCATION SYSTEM CONTROL DISPLAY CONTROL IC501 (3/3) IC901 SERVO board SENSOR board KEY MATRIX KEYIN0 S901–904,906, LCD901 S907–909, LCD SO KEYIN1 • LSW910–918 LIQUID LCD CKO • CRYSTAL D503... - Page 18 CDX-A360 • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS • WAVEFORMS — SERVO BOARD — (CD PLAY) THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. IC2 ia (RFI) (In addition to this, the necessary note is...
-
Page 19: Printed Wiring Boards -Cd Mechanism Section
CDX-A360 5-5. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 17 for Circuit Boards Location. : Uses unleaded solder. TP39 TP38 TP26 TP24 TP41 FMB3 FMA6 TP23 TP29 TP42 TP43 TP45 TP27 TP44 TP37 TP46 TP53... -
Page 20: Schematic Diagram -Cd Mechanism Section (1/2)
CDX-A360 5-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 18 for Waveforms. TP33 TP32 TP31 TP52 TP38 TP39 TP53 R132 C132 R133 TP41 C133 TP50 TP51 TP21 TP22 TP49 TP23 TP24 TP25 TP26 TP28 TP27... -
Page 21: Schematic Diagram -Cd Mechanism Section (2/2)
CDX-A360 • Refer to page 18 for Waveform. • Refer to page 28 for IC Block Diagram. 5-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 30 for IC Pin Descriptions. (Page 20) (Page 25) TP74... -
Page 22: Printed Wiring Board -Main Section
CDX-A360 5-8. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 17 for Circuit Boards Location. : Uses unleaded solder. J330 JC795 CN601 +B 14.4V C484 C474 C775 C774 JW144 FU601 C751 C771 R482 IC750 C765 C764 Q471... -
Page 23: Schematic Diagram -Main Section (1/3)
CDX-A360 • Refer to page 18 for Waveform. 5-9. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 28 for IC Block Diagrams. J330 C484 C474 IC B/D IC401 C401 FB411 FB410 JW102 C411 C410 R8 R29 C435 C432... -
Page 24: Schematic Diagram -Main Section (2/3)
CDX-A360 5-10. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 29 for IC Block Diagram. JC795 C775 C765 C764 C774 IC B/D C751 D751 D752 C750 D753 D754 JC754 JC755 D755 D756 IC750 D757 CN601 D758 D759... -
Page 25: Schematic Diagram -Main Section (3/3)
CDX-A360 • Refer to page 18 for Waveforms. 5-11. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 32 for IC Pin Descriptions. (Page 23) (Page 24) JW45 JW149 JC527 (Page 21) FB603 L301 D719 CN701 FB304 CNP301... -
Page 26: Printed Wiring Boards -Key Section
CDX-A360 5-12. PRINTED WIRING BOARDS — KEY SECTION — • Refer to page 17 for Circuit Boards Location. : Uses unleaded solder. LED902 LED951 LED901 LED952 S901 S902 R996 LED904 LED906 LSW910 R994 LSW917 LSW916 S906 S904 R955 R959 LSW918... -
Page 27: Schematic Diagram -Key Section
CDX-A360 5-13. SCHEMATIC DIAGRAM — KEY SECTION — R972 R981 LED902 LED906 LSW917(2/2) LSW910(2/2) R937 R982 LED901 LED904 LED931 LSW916(2/2) R936 LED945 IC971 LED952 R953 R955 R994 R996 R990 R961 R963 LED951 C971 LED932 R957 R959 R965 R967 R970 R992... - Page 28 CDX-A360 • IC BLOCK DIAGRAMS IC1 BA5968FP-E2 (SERVO Board (2/2)) IC401 BD3806AFS-E2 (MAIN Board (1/3)) OPIN4+ LDCTL OUTR OUTF OPIN4– OPOUT1 OPOUT4 FADER FADER FADER FADER OPIN3+ (0~-58, (0~-58, (0~-58, (0~-58, C BUS -∞dB) -∞dB) -∞dB) -∞dB) GAIN+ATT LOGIC (+10~-29, OPIN3–...
- Page 29 CDX-A360 IC750 TDA8588BJ/N2/R1/M5 (MAIN Board (2/3)) OUT-FL- C BUS OUT-FL+ OUT-RL- PGND3 OUT-RL+ IN-RL IN-FL S-GND PROTECTION/ DIAGNOSTIC IN-FR IN-RR BEEP OUT-RR+ PGND2 OUT-RR- OUT-FR+ STANDBY/ MUTE OUT-FR- CHIP DETECT/ PGND1 DIAGNOSTIC BATTERY TEMPERATURE DIAG DETECTION PROTECTION ENABLE LOGIC ANT-REM...
- Page 30 CDX-A360 • IC Pin Descriptions • IC3 MB90486BPMC-G-177E1 (CD SYSTEM CONTROL) (SERVO BOARD (2/2)) Pin No. Pin Name Pin Description CDON_1500MV Servo 1.5 V power supply control signal output 2 to 5 — Not used. (Open) DRVON Motor drive on/off control signal output...
- Page 31 CDX-A360 Pin No. Pin Name Pin Description EJECT_OK Front panel open signal input (H: eject) OPEN_REQ Front panel open/close request signal output (H: open request) MECON Mechanism deck power supply control signal output CDON Servo power supply control signal output (H: power on)
- Page 32 CDX-A360 • IC501 MB90487APF-G-199E1 (SYSTEM CONTROL) (MAIN BOARD (3/3)) Pin No. Pin Name Pin Description AREASEL2 Destination setting pin AREASEL1 Destination setting pin AREASEL0 Destination setting pin COL_SW Illumination color select signal input BEEP Beep signal output CYRIL_SEL Cyril select signal input...
- Page 33 CDX-A360 Pin No. Pin Name Pin Description UNISCK S-Bus clock signal output 611_SEL Mechanism deck select signal input WMA select signal input Not used. (Open) SIRCS Remote control signal input 65 to 67 Not used. (Open) FLASH_W Memory mode select signal input Not used in this set.
-
Page 34: Exploded Views
CDX-A360 SECTION 6 EXPLODED VIEWS NOTE: • The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by mark 0 or dotted line with mark number in the exploded views are not supplied. Example : 0 are critical for safety. -
Page 35: Front Panel Section
CDX-A360 6-2. FRONT PANEL SECTION RE901 not supplied (KEY board) LCD901 not supplied not supplied not supplied (JACK board) not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1236-400-A PANEL COMPLETE ASSY, FRONT... -
Page 36: Cd Mechanism Section (1) (Mg-611Wa-186//Q)
CDX-A360 6-3. CD MECHANISM SECTION (1) (MG-611WA-186//Q) not supplied (SENSOR board) not supplied not supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3372-444-D CHASSIS (T) SUB ASSY 3-259-033-01 DAMPER (S) 3-253-729-11 SPRING (LR), TENSION COIL... -
Page 37: Cd Mechanism Section (3) (Mg-611Wa-186//Q)
CDX-A360 6-4. CD MECHANISM SECTION (2) (MG-611WA-186//Q) (including M901) not supplied M902 not supplied supplied not supplied not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-1075-644-B CHASSIS (OP) COMPLETE ASSY X-2176-220-1 LEVER (SL) ASSY 3-316-938-91 SCREW (B1.4X5), TAPPING... - Page 38 CDX-A360 6-5. CD MECHANISM SECTION (3) (MG-611WA-186//Q) M903 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-348-993-01 WASHER 2-186-696-31 BRACKET (LEM-N) 2-186-699-31 GEAR (RA1) 3-345-648-91 SCREW (M1.4), TOOTHED LOCK A-1075-641-D ARM ASSY, ROLLER A-1166-303-A GEAR (LE-B) ASSY...
-
Page 39: Cd Mechanism Section (4) (Mg-611Wa-186//Q)
CDX-A360 6-6. CD MECHANISM SECTION (4) (MG-611WA-186//Q) Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 2-186-700-31 GEAR (CHK1) 3-253-755-43 LEVER (D) 3-348-993-01 WASHER A-1075-640-C CHASSIS (M) BLOCK ASSY 3-259-470-33 GEAR (LE1) 2-590-545-34 GEAR (LE2-M) -
Page 40: Electrical Parts List
CDX-A360 SECTION 7 JACK ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by mark 0 or dotted line with mark. the parts list may be different from the they are seldom required for routine service. - Page 41 CDX-A360 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R916 1-216-833-11 METAL CHIP 1/10W R996 1-216-025-11 RES-CHIP 1/10W R920 1-216-809-11 METAL CHIP 1/10W R997 1-216-027-00 RES-CHIP 1/10W R931 1-216-809-11 METAL CHIP 1/10W R932 1-216-809-11 METAL CHIP 1/10W <...
- Page 42 CDX-A360 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C431 1-126-964-11 ELECT 10uF C917 1-163-017-00 CERAMIC CHIP 0.0047uF 10% C432 1-165-908-11 CERAMIC CHIP C918 1-163-017-00 CERAMIC CHIP 0.0047uF 10% C435 1-165-908-11 CERAMIC CHIP C441 1-126-964-11 ELECT 10uF <...
- Page 43 CDX-A360 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark < IC > 1-216-839-11 METAL CHIP 1/10W 1-216-843-11 METAL CHIP 1/10W IC51 6-803-747-01 IC TDA7333013TR 1-216-839-11 METAL CHIP 1/10W IC401 6-708-880-01 IC BD3806AFS-E2 1-216-843-11 METAL CHIP...
- Page 44 CDX-A360 MAIN SENSOR SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R528 1-216-845-11 METAL CHIP 100K 1/10W R691 1-216-845-11 METAL CHIP 100K 1/10W R529 1-216-821-11 METAL CHIP 1/10W R692 1-216-845-11 METAL CHIP 100K 1/10W R531...
- Page 45 CDX-A360 SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-125-777-11 CERAMIC CHIP 0.1uF 8-729-904-87 TRANSISTOR 2SB1197K-R 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 1-162-968-11 CERAMIC CHIP 0.0047uF 10% < RESISTOR > 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 1-125-777-11 CERAMIC CHIP 0.1uF...
- Page 46 CDX-A360 SERVO Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-218-941-81 RES-CHIP 1/16W ACCESSORIES 1-218-941-81 RES-CHIP 1/16W ************ 1-218-965-11 RES-CHIP 1/16W 1-218-973-11 RES-CHIP 1/16W 1-479-077-13 REMOTE COMMANDER (RM-X151) 1-218-973-11 RES-CHIP 1/16W 2-548-729-01 LID, BA TTERY CASE (for RM-X151)
- Page 47 CDX-A360 MEMO...
-
Page 48: Revision History
CDX-A360 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2007.01...