Table of Contents
Advertisement
Table 9. Panel Accessory Kit
Part No.
Description
49-467
2K-ohm EOL resistor assembly for use in UL
listed installations
49-475
Red battery cable
49-475
Black battery cable
BUS Device Headers
Both bus device headers allow you to use SuperBus 2000
touchpads, modules, and devices. Each header can handle
up to 31 devices for a total of 62 devices per panel. Table 10
describes the bus device headers. Use Table A.8 on
page 67 to record all SuperBus device information.
Important !
Use the SuperBus connectors (BUS 1 and BUS 2) head-
ers for either fire or burglary applications. Do not mix fire
and burglary bus devices on either header.
All bus device inputs and outputs must be used for either
fire or burglary applications. Do not mix fire and burglary
applications on inputs and outputs of any bus device.
Table 10. BUS 1 and BUS 2 Headers
Pin
Name
1 (Red)
+12V DC SuperBus DC power supply. 12 VDC @
650 mA maximum. Current limited.
2 (Green) BUS A
SuperBus communication connection.
3 (White) BUS B
4 (Black)
GND
SuperBus common ground connection.
Panel Devices
Devices that you can attach to the panel include SuperBus
2000 modules and SnapCards.
SuperBus 2000 Touchpads
The following touchpads provide complete system pro-
gramming and operational control.
‰ SuperBus 2000 2x20 LCD Touchpad: Provides system
programming and operation control. Large display shows
system messages that prompt users for information when
needed and indicates system status. (60-803-01)
‰ SuperBus 2000 2x20 VFD Touchpad: Provides system
programming and operation control. Large fluorescent
display shows system messages that prompt users for
information when needed and indicates system status. (60-
804-01)
‰ SuperBus 2000 2x20 VFD Fire Touchpad (Commercial
Fire Panels Only): Provides system programming and
operation control. Large fluorescent display shows system
messages that prompt users for information when needed
and indicates system status. (60-810-04)
SuperBus 2000 Modules
The following modules expand the system as described
below:
‰ SuperBus 2000 Commercial RF Transceiver Module:
The transceiver enables the use of wireless zones. When
the transceiver is installed you may use a combination of
wireless and hardwire zones to reach the panel maximum.
6
Qty.
9
2
2
Used for
‰ SuperBus 2000 8Z Input Module (HIM): Provides eight
additional hardwire zone inputs.
‰ SuperBus 2000 4-Relay Output Module (HOM): Pro-
vides four form C relay outputs that can be set up to acti-
vate other signalling devices, based on system events.
‰ SuperBus 2000 Dual Phone Line Module: Allows for
the use of two phone lines. In the event a primary phone
line fails, a secondary line will be used.
‰ SuperBus 2000 Printer Module: Allows you to connect
a printer to the panel.
‰ SuperBus 2000 RS-232 Automation Module
SuperBus 2000 RS-232 Automation module allows you to
connect an Advent panel to a compatible automation sys-
tem. Once connected, the module will enable the automa-
tion system to interpret panel system status.
‰ SuperBus 2000 LED Display Module (LED Driver
*
Board)
: Uses LEDs to display system and devices status.
Up to 16 SuperBus 2000 LED display or terminal boards
may be connected to one driver board.
‰ Voice Siren 25/70 Volt Converter Card
voltage siren audio output capability to fire panels.
SnapCards
The following SnapCards expand the system as described:
‰ 8Z Input SnapCard
+
: Provides eight additional hardwire
zone inputs, of which two are dedicated for using 2-wire
smoke detectors.
‰ 4 Output SnapCard: Provides four form C relay outputs
that can be set up to activate other signalling devices,
based on system events, schedules, or direct control.
‰ 4Z Input/2 Output Combo SnapCard
hardwire zone inputs, one two wire smoke detector loop,
and two outputs that can be set up to activate other signal-
ling devices, based on system events, schedules, or direct
control.
‰ 24V Smoke Loop SnapCard: Adds 24 volt, 2-wire
smoke detector capability to the panel.
Note
If the 24V Smoke Loop SnapCard is used, the panel and
snapcard 2-wire smoke loops are not compatible with the
Sentrol (ESL) 429AT smoke detector.
Installing the System
This section describes how to install the system control
panel. Before starting the installation, plan your system lay-
out and programming using the worksheets provided in
"Appendix A" on page 63.
Installing the system consists of the following:
‰ Determining the Panel Location
‰ Running Wires to the Panel Location
‰ System Wire Lengths
‰ Mounting the Panel (page 8)
‰ Installing Optional SnapCards (page 8)
‰ Connecting SuperBus 2000 Modules and Touchpads
(page 9)
‰ Connecting Detection Devices to Panel Zone Inputs
(page 12)
*) Not investigated by UL.
+) Residential use only.
*
: The
*
: Adds high
+
: Provides three
Advent Commercial Fire System
Hide quick links:
Advertisement
Table of Contents
