JVC KW-XG701E Service Manual
  1. Manuals
  2. Brands
  3. JVC Manuals
  4. Car Receiver
  5. KW-XG701E
  6. Service manual
JVC KW-XG701E Service Manual

JVC KW-XG701E Service Manual

Hide thumbs Also See for KW-XG701E:
Table of Contents

Advertisement

Quick Links

Download this manual
SERVICE MANUAL
2010
3 S ERVICE MANUAL
MA475<Rev.001>
KW-XR810J, KW-XR816U, KW-XR816UH,
KW-XR811E, KW-XR811EY, KW-XR811EU,
only KW-XR810
COPYRIGHT © 2010 Victor Company of Japan, Limited
Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)
Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)
1
PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
2
SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
3
DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9
4
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-21
5
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24
CD RECEIVER
KW-XR817EE
except
KW-XR817

TABLE OF CONTENTS

COPYRIGHT © 2010 Victor Company of Japan, Limited
For KW-XR811/XR817
No.MA475<Rev.001>
2010/3

Advertisement

Table of Contents
loading

Related Manuals for JVC KW-XG701E

Summary of Contents for JVC KW-XG701E

  • Page 1: Table Of Contents

    SERVICE MANUAL CD RECEIVER MA475<Rev.001> 2010 3 S ERVICE MANUAL KW-XR810J, KW-XR816U, KW-XR816UH, KW-XR811E, KW-XR811EY, KW-XR811EU, KW-XR817EE except KW-XR817 only KW-XR810 For KW-XR811/XR817 COPYRIGHT © 2010 Victor Company of Japan, Limited Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade) Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade) TABLE OF CONTENTS PRECAUTION.
  • Page 2 SPECIFICATION KW-XR810 AUDIO AMPLIFIER SECTION 20 W RMS × 4 Channels at 4 Ω and < 1% THD+N Power Output 80 dBA (reference: 1 W into 4 Ω) Signal-to-Noise Ratio 4 Ω (4Ω to 8 Ω allowance) Load Impedance Tone Control Range Bass ±12 dB (50 Hz, 100 Hz, 200 Hz) Q0.7, Q1.0, Q1.4, Q2.0 Middle...
  • Page 3 KW-XR811, KW-XR817 AUDIO AMPLIFIER SECTION Maximum Power Output Front/Rear 50 W per channel 20 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 1% total harmonic Continuous Power Out- Front/Rear put (RMS) distortion. 4 Ω...
  • Page 4 KW-XR816 AUDIO AMPLIFIER SECTION Maximum Power Output Front/Rear 50 W per channel 20 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more than 1% total harmonic Continuous Power Out- Front/Rear put (RMS) distortion. 4 Ω (4Ω to 8 Ω allowance) Load Impedance Tone Control Range Bass...

  • Page 5: Precaution

    SECTION 1 PRECAUTION Safety Precautions (1) This design of this product contains special hardware and voltmeter. many circuits and components specially for safety purpos- Move the resistor connection to each exposed metal es. For continued protection, no changes should be made part, particularly any exposed metal part having a return to the original design unless authorized in writing by the path to the chassis, and measure the AC voltage across...
  • Page 6 Preventing static electricity Electrostatic discharge (ESD), which occurs when static electricity stored in the body, fabric, etc. is discharged, can destroy the laser diode in the traverse unit (optical pickup). Take care to prevent this when performing repairs. 1.5.1 Grounding to prevent damage by static electricity Static electricity in the work area can destroy the optical pickup (laser diode) in devices such as laser products.
  • Page 7 Attention when traverse unit is decomposed *Please refer to "Disassembly method" in the text for the pickup unit. • Apply solder to the short land sections before the card wire is disconnected from the connector on the servo board. (If the card wire is disconnected without applying solder, the pickup may be destroyed by static electricity.) •...

  • Page 8: No.ma475

    Important for laser products 1.CLASS 1 LASER PRODUCT 5.CAUTION : If safety switches malfunction, the laser is able to function. 2.CAUTION : (For U.S.A.) Visible and/or invisible class II laser radiation 6.CAUTION : Use of controls, adjustments or performance of when open.

  • Page 9: Specific Service Instructions

    SECTION 2 SPECIFIC SERVICE INSTRUCTIONS This service manual does not describe SPECIFIC SERVICE INSTRUCTIONS. SECTION 3 DISASSEMBLY Main body (Used model: KW-XR610) (2) Remove the three screws C attaching the Bottom chassis. (See Fig.3) 3.1.1 Removing the Front panel (See Fig.1) (3) Remove the three screws D and one screw E attaching the (1) Remove the two screws A attaching the both side of the Heat sink.

  • Page 10: See Fig.

    (2) Remove the three screws K attaching the Main board. (See Fig.5) (3) Disconnect B-B connector CN501 of the Main board con- nected the CD mechanism and Main board. (See Fig.5) CN501 Fig.5 3.1.4 Removing the CD mechanism (See Fig.6) (1) Remove the three screws L attaching the CD mechanism.
  • Page 11 CD MECHANISM assembly section Mechanism • Remove the CD MECHANISM assembly from the main body. control board CN102 3.2.1 Removing the MECHANISM CONTROL BOARD as- sembly (See Fig.1 and 2) (1) From the bottom side of CD MECHANISM assembly, re- move the solders from the soldered sections (a, b and c) on the MECHANISM CONTROL BOARD assembly.
  • Page 12 3.2.2 Removing the top cover (See Fig.3 to 5) • Remove the MECHANISM CONTROL BOARD assembly. Top cover (1) From the front side of the CD MECHANISM assembly, change the hook position of the two roller springs. (See Fig.3.) (2) From the side of the CD MECHANISM assembly, remove the six screws C attaching the top cover.
  • Page 13 3.2.3 Removing the roller (See Fig.6) • Remove the MECHANISM CONTROL BOARD assembly and Roller coller top cover. (1) From the bottom side of the top cover, remove the screw D attaching the gear holder. (2) Remove the R.holder assembly from disc plate, and then Washer take out the roller from R.holder assembly in the direction Gear holder...
  • Page 14 3.2.5 Removing the mechanism section (See Fig.9 and 10) • Remove the MECHANISM CONTROL BOARD assembly and Mechanism section top cover. (1) From the top side of the CD MECHANISM assembly, Mecha frame spring spring remove the two screws F attaching the loading motor assembly.
  • Page 15 3.2.6 Removing the slide cam (L) (See Fig.11 to 13) • Remove the MECHANISM CONTROL BOARD assembly, top Slide cam(L) cover and mechanism section. (1) From the top side of the mecha frame, remove the screw G attaching the cam cover. (See Fig.11.) (2) Take out the cam cover from mecha frame in an upward direction.

  • Page 16: No.ma475)1

    3.2.7 Removing the F.lock lever and slide cam (R) (See Slide cam(R) assembly Fig.14 and 15) • Remove the MECHANISM CONTROL BOARD assembly, top cover and mechanism section. F.lock lever (1) From the top side of the mecha frame, take out the slide cam (R) assembly in an upward direction.
  • Page 17 3.2.9 Removing the clamper assembly (See Fig.17) • Remove the MECHANISM CONTROL BOARD assembly, top cover and mechanism section. (1) From the top side of the mechanism section, release the clamper spring. (2) Move the clamper assembly in the direction of the arrow, and then release the joints (k and m).
  • Page 18 3.2.10 Removing the feed motor (See Fig.18 and 19) • Remove the MECHANISM CONTROL BOARD assembly, top cover, mechanism section and clamper assembly. (1) From the bottom side of the T.M chassis assembly, remove the two screws H attaching the feed motor assembly. (See Trigger arm Feed motor assembly Fig.18.)
  • Page 19 3.2.13 Removing the pickup assembly (See Fig.21 to 22) • Remove the MECHANISM CONTROL BOARD assembly, top cover, mechanism section, clamper assembly and feed motor assembly. Pick up assembly Main shaft Caution: • Do not touch section u on the pickup assembly. (See Fig.21 and 22.) (1) From the bottom side of the T.M chassis assembly, move the pickup assembly in the direction of the arrow from the...
  • Page 20 3.2.14 Removing the spindle motor (See Fig.23 and 24) • Remove the MECHANISM CONTROL BOARD assembly, top cover, mechanism section, clamper assembly, feed motor assembly and pickup assembly. (1) From the top side of the T.M chassis assembly, remove the CD T.table assembly from the spindle motor.

  • Page 21: Adjustment

    SECTION 4 ADJUSTMENT Test instruments required for adjustment Standard volume position (1) Digital oscilloscope (100MHz) Balance and Bass &Treble volume : lndication"0" (2) Digital tester Loudness : OFF (3) Test Disc Dummy load (4) Extension cable : EXTGS004-26PL Exclusive dummy load should be used for AM,and FM. Standard measuring conditions For FM dummy load, there is a loss of 6dB between SSG output Power supply voltage DC14.4V(10.5 to 16V)
  • Page 22 Service Mode 4.6.1 Service mode setting (1) Push POWER BUTTON (Power ON) (2) Set to service mode Keep this state more 3 seconds while connecting pressing the [MENU] button and [ ] button sequentially. (3) Select the menu with [VOL -] and [VOL+], and decide it with [Enter] button. (4) When the [BACK] button is pushed, it returns to the former menu.
  • Page 23 4.6.2 Mechanical Error Detail Codes Condition Details Error Code Detail Code Disc Loading Error (1) B1 Time Out After detecting SW1=L, it does not become SW2=L 0011 (2) B2 Time Out After detecting SW2=H, it does not become SW2=L 0012 (3) C1 Time Out After detecting SW2=L, it does not become SW2=H 0013...

  • Page 24: Troubleshooting

    SECTION 5 TROUBLESHOOTING 16 PIN CORD DIAGRAM (For KW-XR810) Black Green Gray GN/BK WH/BK Blue Orange VI/BK GY/BK White Yellow Violet BL/WH OR/WH OR/WH GN/BK VI/BK WH/BK GY/BK 3 BL/WH 1-24 (No.MA475<Rev.001>)
  • Page 25 16 PIN CORD DIAGRAM (For KW-XR811, KW-XR817) Black Green Gray GN/BK WH/BK Blue Orange VI/BK GY/BK White Yellow Violet BL/WH OR/WH OR/WH NC NC YL 2 BL/WH OR/WH BL/WH RD 3 BK 8 GN GN/BK VI/BK VI VI/BK GY/BK WH/BK WH/BK GN GN/BK GY/BK...
  • Page 26 16 PIN CORD DIAGRAM (For KW-XR611) Black Green Gray GN/BK WH/BK Blue Orange VI/BK GY/BK White Yellow Violet BL/WH OR/WH BL/WH 2 RD OR/WH GN/BK VI/BK WH/BK GY/BK 1-26 (No.MA475<Rev.001>)
  • Page 28 Victor Company of Japan, Limited Mobile Entertainment Division 10-1,1chome,Ohwatari-machi,Maebashi-city,371-8543,Japan (No.MA475<Rev.001>) Printed in Japan...

  • Page 29: Schematic Diagrams

    SCHEMATIC DIAGRAMS CD RECEIVER KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE (No.MA475<Rev.001>)1/21...
  • Page 30 ■ PRECAUTIONS ON SCHEMATIC DIAGRAMS Due to the improvement in performance, some part numbers shown in the circuit diagrams may not agree with those indicated in the Parts List. The parts numbers, values and rated voltage etc. in the Schematic Diagrams are for reference only.
  • Page 31 IC801 3.3V TRK+, TRK- BUS-I/O, /BUS-I/O, BUSSCK ILM.10V IC921 (RDS) CD DRIVER B.MUTE TRACKING FCS+, FCS- JVC BUS CH.L CONTROL (CN441) 3.3V REG. CH.R COIL SW1, SW2 VF1, VF2, VT1 VT2, LD, MD PICK UP Used on U version only U0+, U0- TRST, MUTE.CTL...

  • Page 32: Main Section

    AMPKILL AMPKILL C721 USB RESET 0.047 USBRX 3.2V 3.2V SUBMUTE USBRX SUBMUTE USBTX 3.2V RESET USBTX NOT USED EEPROMDI JVC BUS BUS-I/O KW-XR811E, KW-XR817EE MODELS ONLY 6.8K EEPROM R809 BUSSCK /BUS-I/O R1EX24016ASAA-X IC771 BUSINT J801 R813 C771 R721 QNZ0095-001 R814 3.3V...
  • Page 33 <Main section 2> USE OF OTHER DIV : JEIN USB5V USB5V UH0+ UH0+ UH0+ UH0- UH0- UH0- SW5V SW5V USBTX USB-TX USBRX USB-RX TRST TRST MUTE.CTL MUTE.CTL D501 Q501 2SB1424/R/-W GS1J-LTP-X R520 10 3.4V 5.5V 3.3V 3.3V D502 GS1J-LTP-X 4.9V R509 8.2k 5-CH BTL DRIVER C504 NI...
  • Page 34 <Switch section> D609 D610 NSSM065T-X NSSM065T-X FOR PROGRAMMING MICON IC661 SWITCH PWB GEB10295A1 REMOCON IC681 ENCODER EN601 KSM-2003TN2M QSW1280-001 VOL1 VOL2 C669 C668 CN601 SELECT 0.047 KEY MATRIX QGB1004J2-24X 0.047 R625 R624 R623 R622 R621 B608 2.7K 1.8K 1.2K KEY0 KEYDATA KEYDATA D681...
  • Page 35 <Module section> K449,K450:NQR0286-007X NQR0536-001X L409 CN441 QGG2011M1-18X K450 USB0.EN NOR FLASH SDRAM R404 K449 USB1.EN K441 NQR0502-001X R405 IC441 IC442 CD16M EN29LV160BT70TP M12L1281687TG2T C443 XA16 22/6.3 C444 USB3.3V XA15 3.0V 3.2V 3.2V R408 XD15 R441 XA14 0.9V 3.2V C445 0.2V 0.2V To Main section 2 /BYTE...
  • Page 36 <Mecha control section> To Rest switch section FEED SPINDLE MOTOR MOTOR To Photo section OPTIMA-750A1 PICKUP ASSEMBLY CN102 TRK- TRK- HDU-120 TRK+ TRK+ FCS+ FCS+ FCS- FCS- FOCUS COIL TRACKING COIL MECHA PWB LVA10874-A1 To Main section 2 CN501 No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)8/21...
  • Page 37 <Photo section> PHOTO TR.PWB LVA10874-A2 Q302 PS1191RB22/BC/X To Mecha control section Q301 PS1191RB22/BC/X No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)9/21...
  • Page 38 <Rest switch section> NSW0291-001X To Mecha control section REST SW PWB LVA10874-A3 No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)10/21...

  • Page 39: Main Board

    <Main board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) J801 J321 IC301 R305 C319 R343 R342 R333 Q332 R353 R322...
  • Page 40 <Main board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) IC301 J801 CN901 L901 J321 C901 D901 R901 CN702 R853 CN501...
  • Page 41 <Switch board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) D608 D621 D620 D623 S671 S666 S676 S677 S661 S675 S674...
  • Page 42 <Switch board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) C605 D622 C607 D624 C658 C657 R694 C656 R680 C655 C654...
  • Page 43 <LED board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)15/21...
  • Page 44 <LED board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)16/21...
  • Page 45 <Module board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) 1:TDI 2:TMS 3:TCK 4:TDO 5:TRST 1P1A X401 C407 GEA10288- C491 C492...
  • Page 46 <Module board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) 4P1A C453 CN441 C451 GEB10288A C452 C448 R403 IC442 R458 C427...
  • Page 47 <Mecha control board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) CN102 B102 CN101 BLACK REST ORANGE YELLOW WHITE Q201 R202...
  • Page 48 <Photo board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) ORANGE MARK LVA10873-A2 BROWN No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)20/21...
  • Page 49 <Rest switch board> (Lead free solder used in the board (material : Sn-Ag-Cu, melting point : 219 Centigrade)) (Lead free solder used in the board (material : Sn-Cu, melting point : 230 Centigrade)) No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)21/21...

  • Page 50: Parts List

    PARTS LIST CD RECEIVER KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE (No.MA475<Rev.001>)1/21...
  • Page 51 ■ PRECAUTIONS ON SCHEMATIC DIAGRAMS Due to the improvement in performance, some part numbers shown in the circuit diagrams may not agree with those indicated in the Parts List. The parts numbers, values and rated voltage etc. in the Schematic Diagrams are for reference only.
  • Page 52 Exploded view of general assembly Block No.M1MM J,E,EY,EU Switch board Module board Main board The parts without symbol number are not service. No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)3/21...
  • Page 53 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local General assembly <M1MM> GE10275-001A TOP CHASSIS GE10276-001A BOTTOM CHASSIS GE33960-006A REAR BRACKET GE33960-005A REAR BRACKET B,C,D,E,F GE33960-004A REAR BRACKET GE33961-001A...
  • Page 54 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local Q701 2SA812A/5-6/-X TRANSISTOR Q701 ISA1530AC1/QR/X TRANSISTOR Q702 2SC1623A/5-6/-X TRANSISTOR Q702 2SC3928A/QR/-X TRANSISTOR Q703 RT1N141C-X DIGI TRANSISTOR Q703 UN2211-X TRANSISTOR...
  • Page 55 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local NCBA1CK-103W C CAPACITOR 0.01uF 16V K NCB31AK-105X C CAPACITOR 1uF 10V K NCB31AK-224X C CAPACITOR 0.22uF 10V K NCBA1CK-104W C CAPACITOR 0.1uF 16V K...
  • Page 56 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local C371 NCB31CK-104X C CAPACITOR 0.1uF 16V K C372 NCBA1HK-152W C CAPACITOR 1500pF 50V K C381 QEKJ1HM-475Z E CAPACITOR 4.7uF 50V M C382...
  • Page 57 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local C784 QEKJ1CM-107Z E CAPACITOR 100uF 16V M C785 QEKJ0JM-476Z E CAPACITOR 47uF 6.3V M C786 NCBA1AK-104W C CAPACITOR 0.1uF 10V K C851...
  • Page 58 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local R273 NRSA6AJ-0R0W MG RESISTOR 0Ω 1/16W J A,D,E,F,G R274 NRSA6AJ-333W MG RESISTOR 33kΩ 1/16W J R275 NRSA63J-821X MG RESISTOR 820Ω...
  • Page 59 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local R586 NRSA6AJ-822W MG RESISTOR 8.2kΩ 1/16W J R587 NRSA6AJ-273W MG RESISTOR 27kΩ 1/16W J R588 NRSA6AJ-273W MG RESISTOR 27kΩ...
  • Page 60 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local R922 NRSA6AJ-0R0W MG RESISTOR 0Ω 1/16W J R923 NRSA6AJ-0R0W MG RESISTOR 0Ω 1/16W J R924 NRS125J-390X MG RESISTOR 39Ω...
  • Page 61 CD mechanism assembly Block No.MBMM Grease JVG-31N FG-87HS JVS-1003 Photo board Rest switch board Back side 11.1mm ± 0.1mm Mecha control board 11.1mm ± 0.1mm The parts without symbol number are not service. No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)12/21...
  • Page 62 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local FLM-CD5-1D CD mechanism <MBMM> LV11256-001A MECHA FRAME A,B,C,D,E,F,G LV36800-002A LINK ARM A,B,C,D,E,F,G LV44658-001A LINK SPRING A,B,C,D,E,F,G LV22300-002A SLIDE CAM (L) A,B,C,D,E,F,G...
  • Page 63 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local D640 MA8051/M/-X Z DIODE D641 RKZ5.1B2KG-X Z DIODE D641 MA8051/M/-X Z DIODE D651 HSU119-X SI DIODE D651 MA111-X SI DIODE...
  • Page 64 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local R670 NRSA63J-103X MG RESISTOR 10kΩ 1/16W J R672 NRSA63J-331X MG RESISTOR 330Ω 1/16W J R673 NRSA63J-331X MG RESISTOR 330Ω...
  • Page 65 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local C421 NCBA1CK-104W C CAPACITOR 0.1uF 16V K C422 NCBA1CK-104W C CAPACITOR 0.1uF 16V K C423 NCBA1CK-104W C CAPACITOR 0.1uF 16V K C424...
  • Page 66 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local R605 NRSA6AJ-220W MG RESISTOR 22Ω 1/16W J R606 NRSA6AJ-220W MG RESISTOR 22Ω 1/16W J R607 NRSA63J-220X MG RESISTOR 22Ω...
  • Page 67 Packing materials and accessories(J,E,EY,EU,EE) Block No.M3MM No additional / supplemental order of WARRANTY CARDs are available. E,EY,EU The parts without symbol number are not service. No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)18/21...
  • Page 68 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local Packing and accessories J,E,EY,EU,EE<M3MM> GET0661-001A INST BOOK ENG SPA FRE GET0663-001A INST BOOK GET0664-001A INST BOOK RUS UKR GET0663-003A INST BOOK...
  • Page 69 Packing materials and accessories(U,UH) Block No.M4MM No additional / supplemental order of WARRANTY CARDs are available. The parts without symbol number are not service. No.MA475 created date:2010-03-17 (No.MA475<Rev.001>)20/21...
  • Page 70 MODEL MARK MODEL MARK MODEL MARK MODEL MARK KW-XR810J KW-XR816U KW-XR816UH KW-XR811E KW-XR811EY KW-XR811EU KW-XR817EE Safe Symbol No. Parts No. Parts Name Description Local Packing and accessories U,UH<M4MM> GET0662-001A INST BOOK ENG THA GET0662-003A INST BOOK GET0662-006A INSTALL MANUAL ENG THA GET0662-007A INSTALL MANUAL KOR CHI(TAIWAN) ARA PER...

This manual is also suitable for:

Kw-xg701eyKw-xg700jKw-xg704uiKw-xg701exKw-xg705uKw-xg705un ... Show all

Table of Contents