Advertisement
Table of Contents
Safety Precautions ••••••••••••••••••••••••••••••••••••••2
••••••••••••••••••••••••••••••••••••••6
How to Use Blender ••••••••••••••••••••••••••••••••••••8
How to Use Dry Mill •••••••••••••••••••••••••••••••••• 11
Safety Lock ••••••••••••••••••••••••••••••••••••••••••••• 14
Circuit Breaker Protection ••••••••••••••••••••••••••• 15
How to Clean •••••••••••••••••••••••••••••••••••••••••• 16
Troubleshooting ••••••••••••••••••••••••••••••••••••••• 18
••••••••••••••••••••••••••••••• Back cover
Thank you for purchasing the Panasonic product.
• This product is intended for household use only.
• Please read these instructions carefully and follow safety
precautions when using this product.
• Before using this product please give your special attention to
"Safety Precautions" (Page 2).
• Please keep this Operating Instructions for future use.
乾磨器的使用方法
自動截斷電源裝置
Operating Instructions
MX-GX1561/MX-GX1511
Model No.
Blender
(household use)
ﻫﺬﻩ
ﻫﺬﺍ
ﻫﺬﺍ
ﻫﺬﺍ
ﻫﺬﺍ
Advertisement
Related Manuals for Panasonic MX-GX1561
Summary of Contents for Panasonic MX-GX1561
-
Page 1: Table Of Contents
How to Clean •••••••••••••••••••••••••••••••••••••••••• 16 Troubleshooting ••••••••••••••••••••••••••••••••••••••• 18 ••••••••••••••••••••••••••••••• Back cover Thank you for purchasing the Panasonic product. • This product is intended for household use only. • Please read these instructions carefully and follow safety precautions when using this product. -
Page 2: Safety Precautions
Safety Precautions Always follow these precautions ﻫﺬﻩ In order to prevent the risk of danger to the users of this product or those nearby, and damaging property, be sure to follow the safety precautions outlined below. ■ The following signs are used for precautions. They are separated depending on the degree of the danger or damage that may occur if their contents are ignored while using this unit. - Page 3 WARNING ﻫﺷﺩﺍﺭ This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the product by a person responsible their safety. Children should be supervised to ensure that they do not play with the product.
- Page 4 WARNING ﻫﺷﺩﺍﺭ Please make sure that voltage used for this product Remove dusts or dirts at plug regularly. is suitable to the local area voltage. ﺍﻟﺘﺄﻛﺪ May cause insulation failure or fire due to humidity. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly persons in order to avoid a hazard.
- Page 5 ﺗﻧﺑﻳﻪ 停止操作 ﺩﻗﺎﺋﻖ 類 中斷 在清潔、乾燥及堅固的平台上操作本產品。 Remove packing materials, such as plastic bags or plug cap etc from the appliance. Discard them or keep them away from babies and children. （Otherwise it may cause suffocation.） 將攪拌機從馬達罩拆下前， ﻣﻮﺍﺩ ﺑﺴﺘﻪ ﺑﻨﺪی ﺍﺯ ﻗﺒﻴﻞ ﮐﻴﺴﻪ ﻫﺎی ﭘﻼﺳﺘﻴﮑﯽ ﻳﺎ ﺩﺭﭘﻮﺵ .ﺳﻮﺭﺍﺧﮕﻴﺮ...
-
Page 6: Parts
乾磨器 Switch buttons 開關 rotates only while the button is being pressed)”, 馬達罩 乾磨器容器 乾磨器 乾 乾... - Page 7 To disassemble Blender To disassemble Mill Turn blender container base Twist the mill container base counterclockwise to disassemble. counterclockwise. To assemble Blender To assemble Mill Turn blender container clockwise to mill container base assemble. • Make sure that gasket is set properly and container is tightened properly to prevent mill gasket...
-
Page 8: How To Use Blender
How to Use Blender CAUTIONS: • First, dice the ingredients (cut them into cubes measuring 1 to 2 cm), and put them in water. • Put the ingredients in the container starting with the softer ones • Do not place ingredients with a maximum total volume •... - Page 9 Place the ingredients in the blender container. Check that the cover is in place to prevent the ingredients from out. Mount the blender container on the motor housing. Twist the container clockwise until it locks into place. When adding ingredients or seasonings, remove/attach inner cap whilst holding the container.
- Page 10 After the ingredients have been blended, Disconnect the power plug from the power outlet. Twist the blender container counterclockwise to remove it from the motor housing, and take out the processed ingredients. When disconnecting the power plug, be absolutely sure to take hold of the molded plug.
-
Page 11: How To Use Dry Mill
乾磨器的使用方法 ﺍﻟﻤﺠﻔﻒ... - Page 12 Turn the mill container upside down, and place the ingredients in it. Twist the mill container base clockwise until it locks into place, and mount it onto the mill container. Place the mill container and mill container base on the motor housing. Twist the container and base clockwise until they lock into place.
- Page 13 After the ingredients have been mixed Disconnect the power plug from the power outlet. Remove the mill container base from the motor housing, turn it upside down, and tap the container gently with your hand to dislodge the ingredients from the cutter. Remove the mill container base by twisting counterclockwise and take out the processed ingredients.
-
Page 14: Safety Lock
Safety Lock The safety lock has been designed to prevent the blender Safety lock pin from switching on when container is not properly in place. Do not push the safety lock pin with any implement, stick etc. assembling, motor does not operate. 刀座... -
Page 15: Circuit Breaker Protection
Circuit Breaker Protection 截 If the motor is subjected to an excessive load, its protection device is tripped, shutting down the motor automatically. It is reset by taking the steps described below. Reduce the amount of the ingredients inside the container by half. and then press the following buttons one-at-a-time in order: >... -
Page 16: How To Clean
How to Clean NOTES: • Before cleaning the blender, disconnect the power plug from the power outlet. • Handle the cutter carefully. • To clean the parts, use cold or lukewarm water and a soft sponge. • Do not use steel brushes or other abrasive cleaning materials or utensils. •... - Page 17 Containers and plastic parts Mill cutter 乾 Carefully clean mill cutter with a brush. Do not use water. 乾 Wash the parts using a soft sponge soaked in diluted kitchen detergent (neutral). To remove ingredients stuck in the cutter, carefully clean it with a brush. Then rinse thoroughly with water, and allow the parts to dry out.
-
Page 18: Troubleshooting
Troubleshooting Problems Possible cause Page See P.9 & The blender does not operate P.12 The blender stops operating • The Circuit Breaker Protection of the motor has been tripped. See P.15 midway through operation. Check whether prohibited, hard or too many ingredients have been placed in the container. - Page 19 Note /註 You can identify the date of manufacturing by number which is marked on bottom side of the unit. Number marked on bottom side of the unit: X X X X X X Fifth and sixth digits: day (in number) 01, 02, 03...31 Third and fourth digits: month (in number) 01--January, 02--February, ...12--December First and second digits: year (last two digits of the year in number)
- Page 20 220 V 50 Hz MX-GX1561: 220 W / MX-GX1511: 230 W MX-GX1561: approx. 3.4 kg Approx. 1.8 kg MX-GX1511: approx. 2.2 kg 乾磨器 厘米 厘米 厘米 千克 千克 千克 :MX-GX1511 / :MX-GX1561 :MX-GX1511 / :MX-GX1561 Web Site: http://www.panasonic.com X0921-351...