GE C30 Instruction Manual page 346

FLEXLOGIC
Operand type
INPUTS/OUTPUTS:
Contact inputs
INPUTS/OUTPUTS:
Contact outputs,
current
(from detector on
form-A output only)
INPUTS/OUTPUTS:
Contact outputs,
voltage
(from detector on
form-A output only)
INPUTS/OUTPUTS:
Direct inputs
INPUTS/OUTPUTS:
RxGOOSE DPS
5
INPUTS/OUTPUTS:
RxGOOSE Booleans
INPUTS/OUTPUTS:
Virtual inputs
INPUTS/OUTPUTS:
Virtual outputs
LED INDICATORS:
Enhanced and
standard front panels
5-152
Operand syntax
Cont Ip 1 On
Cont Ip 2 On
↓
Cont Ip 1 Off
Cont Ip 2 Off
↓
Cont Ip 120 On
Cont Ip 120 Off
Cont Op 1 IOn
Cont Op 2 IOn
↓
Cont Op 72 IOn
Cont Op 1 VOn
Cont Op 2 VOn
↓
Cont Op 72 VOn
Cont Op 1 VOff
Cont Op 2 VOff
↓
Cont Op 72 VOff
DIRECT INPUT 1 On
↓
DIRECT INPUT 64 On
RxG DPS 1 BAD
RxG DPS 1 INTERM
RxG DPS 1 OFF
RxG DPS 1 ON
RxG DPS 2 to 5
RxG Bool 1 On
RxG Bool 2 On
RxG Bool 3 On
↓
RxG Bool 256 On
Virt Ip 1 On
Virt Ip 2 On
Virt Ip 3 On
↓
Virt Ip 64 On
Virt Op 1 On
Virt Op 2 On
Virt Op 3 On
↓
Virt Op 96 On
LED IN SERVICE
LED TROUBLE
LED TEST MODE
LED TRIP
LED ALARM
LED PICKUP
LED VOLTAGE
LED CURRENT
LED FREQUENCY
LED OTHER
LED PHASE A
LED PHASE B
LED PHASE C
LED NEUTRAL/GROUND
Operand description
(does not appear unless ordered)
(does not appear unless ordered)
↓
(does not appear unless ordered)
(does not appear unless ordered)
↓
(does not appear unless ordered)
(does not appear unless ordered)
(does not appear unless ordered)
(does not appear unless ordered)
↓
(does not appear unless ordered)
(does not appear unless ordered)
(does not appear unless ordered)
↓
(does not appear unless ordered)
(does not appear unless ordered)
(does not appear unless ordered)
↓
(does not appear unless ordered)
Flag is set, logic=1
↓
Flag is set, logic=1
Asserted while the RxGOOSE double-point status input is in the bad state
Asserted while the RxGOOSE double-point status input is in the intermediate
state
Asserted while the RxGOOSE double-point status input is off
Asserted while the RxGOOSE double-point status input is on
Same set of operands as per RxG DPS 1
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
Flag is set, logic=1
↓
Flag is set, logic=1
Asserted when the front panel IN SERVICE LED is on
Asserted when the front panel TROUBLE LED is on
Asserted when the front panel TEST MODE LED is on
Asserted when the front panel TRIP LED is on
Asserted when the front panel ALARM LED is on
Asserted when an element picks up and to turn PICKUP LED on
Asserted when a voltage element involved and to turn VOLTAGE LED on
Asserted when a current element involved and to turn CURRENT LED on
Asserted when a frequency element involved and to turn FREQUENCY LED on
Asserted when a composite element involved and to turn OTHER LED on
Asserted when phase A involved and to turn PHASE A LED on
Asserted when phase B involved and to turn PHASE B LED on
Asserted when phase C involved and to turn PHASE C LED on
Asserted when a neutral or ground element involved and to turn NEUTRAL/
GROUND LED on
C30 CONTROLLER SYSTEM – INSTRUCTION MANUAL
CHAPTER 5: SETTINGS