English 184 mm CORDLESS CIRCULAR SAW DCS570 Congratulations! EC-Declaration of Conformity You have chosen a D WALT tool. Years of experience, thorough Machinery Directive product development and innovation make D WALT one of the most reliable partners for professional power tool users.
English SAFETY INSTRUCTIONS FOR ALL SAWS 4) Power tool use and care a ) Do not force the power tool. Use the correct power Cutting Procedures tool for your application. The correct power tool DANGER: Keep hands away from cutting area will do the job better and safer at the rate for which it and the blade.
English Additional Safety Instructions for Circular b ) When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw Saws motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw •...
English SAVE THESE INSTRUCTIONS Do not operate charger if it has received a sharp blow, • been dropped, or otherwise damaged in any way. Take it Chargers to an authorised service centre. WALT chargers require no adjustment and are designed to be •...
English hot/Cold Pack Delay Do not charge or use battery in explosive atmospheres, • such as in the presence of flammable liquids, gases or When the charger detects a battery pack that is too hot or too dust. Inserting or removing the battery from the charger may cold, it automatically starts a Hot/Cold Pack Delay, suspending ignite the dust or fumes.
English WALT batteries comply with all applicable shipping Storage Recommendations regulations as prescribed by industry and legal standards which 1. The best storage place is one that is cool and dry away include UN Recommendations on the Transport of Dangerous from direct sunlight and excess heat or cold.
English Battery Type Blade clamping screw Kerf indicator The DCS570 operates on a 18 volt battery pack. Bevel adjustment lever These battery packs may be used: DCB181, DCB182, DCB183, DCB183B, DCB184, DCB184B, DCB185, DCB187, DCB546, Blade lock button DCB547. Refer to Technical Data for more information.
English Fuel Gauge Battery Packs (Fig. A) right-hand threads and must be turned counterclockwise to loosen). Some D WALT battery packs include a fuel gauge which 3. Remove the blade clamping screw 8 and outer clamp consists of three green LED lights that indicate the level of washer 16 ...
Page 16
English 4. MATERiAls ThAT REQUiRE EXTRA ATTEnTiOn 184 mm Diameter a. Wet timber Application Teeth b. Green timber (material freshly cut or not kiln dried) c. Pressure treated timber (material treated with preservatives or anti-rot chemicals) General Purpose 5. UsE OF DUll OR DiRTY BlADEs Finish a.
Bevel Detent (Fig. A, G) • Make sure the saw blade rotates in the direction of the arrow on the blade. The DCS570 is equipped with a bevel detent feature. As you • Do not use excessively worn saw blades. tilt the base plate 5 ...
English Figures J and K show proper sawing position. Figures L and M Pocket Cutting (Fig. O) show an unsafe condition. Hands should be kept away from WARNING: Never tie the blade guard in a raised position. cutting area, and power cord is positioned clear of the cutting Never move the saw backwards when pocket cutting.
English To Tighten the lever: 1. Hold the bevel adjustment lever 10 and loosen the bevel locknut 24 Lubrication 2. Adjust the bevel adjustment lever by rotating it in the desired direction about 1/8 of a revolution. Self lubricating ball and roller bearings are used in the tool and 3.
Page 20
Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)