Table of Contents
Advertisement
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
21. Damage Requiring Service
Unplug this product from the wall power out-
let and refer servicing to qualifi ed service
personnel under the following conditions:
a. If the power-supply cord or plug is dam-
aged.
b. If liquid has been spilled, or objects have
fallen into the product.
c. If the product has been exposed to rain or
water.
d. If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by the
operating instructions, as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualifi ed technician to restore
the product to its normal operation.
e. If the product has been dropped or the
cabinet has been damaged.
f. If the product exhibits a distinct change in
performance.
Caution: Refer all servicing to qualifi ed
service personnel.
22. Servicing
Caution: These servicing instruc-
tions are for use by qualifi ed
service personnel only. To reduce
the risk of electrical shock, do not perform
any servicing other than that described in
the operating instructions unless you are
qualifi ed to do so.
23. Replacement Parts
When replacement parts are required, be
sure the service technician uses replacement
parts specifi ed by the manufacturer or that
have the same characteristics as the original
parts. Unauthorized substitutions may result
in fi re, electric shock, or other hazards.
4
24. Safety Check
Upon completion of any service or repairs to
this product, ask the service technician to
perform safety checks to determine that the
product is in proper operating condition.
OAT100R Rack Installation
(also see pages 11 and 12)
To install the OAT100R in a rack:
•
Carefully slide the OAT100R into a standard
19-inch equipment rack.
•
When mounting in the rack, make sure to use
the appropriate hardware. ALL FOUR MOUNT-
ING SCREWS MUST BE USED.
•
This equipment is not designed to support
other devices. Do NOT stack other equipment
on the top of the OAT100R.
•
Rear cabling must be dressed and supported
so that the weight of the cabling is not a strain
on the OAT100R connectors.
•
MOUNTING OF THE EQUIPMENT IN THE
RACK SHOULD BE SUCH THAT A HAZARD-
OUS CONDITION IS NOT ACHIEVED DUE
TO UNEVEN MECHANICAL LOADING.
Rack-mount Considerations
A. Elevated Operating Ambient
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature
of the rack environment may be greater than
room ambient. Therefore, consideration should
be given to installing the equipment in an
environment compatible with the maximum
ambient temperature (Tma) specified by the
manufacturer (see Specifications information
in this document).
(Continued on next page)
206-4219
Dimensions
Height:
1.692 inches (42.977 mm)
Width:
19.0 inches (482.6 mm) with mounting brackets attached
(for EIA standard 19-inch rack mount)
Depth:
8.5 inches (215.9 mm)
Weight:
4.45 pounds (2.02 kgrms) rack-only weight
Environmental Storage Conditions
Temperature:
-20° to 70° Celsius
-4° to 158° Fahrenheit
Humidity:
95% non-condensing
Environmental Operating Conditions
Temperature (Tma):
0° to 40° Celsius
32° to 104° Fahrenheit
Humidity:
95% non-condensing
Electrical
RF Out Connector:
RF Output Span:
RF Output Frequency Range:
Active Output Level at RF Out jack:
RF IN Ports (8):
RF Input Frequency Range:
RF Input Signal Level:
DC Input:
Ethernet Connector (Control Port):
Ethernet Connector (Feature Port):
USB Port:
Note: Design and specifi cations subject to change without prior notice.
206-4219
Specifi cations
Type 'F'
4 Contiguous Channels (typically 24 MHz)
54 MHz to 864 MHz
-6 dBm (+42 dBmV) Min.
Type 'F', 75 Ohm
Terrestrial Channels 2 to 69
+3 dBm (+52 dBmV) to -83 dBm (-34 dBmV)
+12V DC @ 2.6 Amps
10/100/1000BaseT, RJ-45
1000BaseT Full Duplex, RJ-45
USB 2.0
25
Advertisement
Table of Contents
