1. Manuals
  2. Brands
  3. Philips Manuals
  4. Monitor
  5. 150S8FB/00
  6. Service manual

Philips 150S8FB/00 Service Manual

Lcd color monitor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Service
Service
Service
Description
Table Of Contents.....................................................1
Revision List................................................................2
Important Safety Notice.............................................3
1. Monitor Specifications..............................................4
2. LCD Monitor Description..........................................5
3. Operation instructions.............................................6
3.1General Instructions..................................... ...6
3.2 Control buttons............................................ ...6
3.3 Adjusting the Picture...............................................8
3.4 Connecting to the PC ........................................12
4. Input/Output Specification.....................................13
4.1 Input Signal Connector.........................................13
4.2 Factory Preset Display Modes...............................13
4.3 Pixel Defect Policy..........................................14
4.4 Failure Mode OF Panel..................................17
5. Block Diagram.................................................18
5.1 Software Flow Chart.............................................18
5.2 Electrical Block Diagram....................................20
6. Schematic Diagram.............................................22
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE
CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES
Published by Philips CE
Page Description
SAFETY NOTICE
Copyright reserved
Subject to modification ○
150S8FB/93
150S8FB/00
150S8FS/00
150S8FS/78
150S8FB/78
150S8FBJ/78
6.1 Main Board....................................................22
6.2 Power Board.....................................................26
6.3 Key Board...................................................28
7. PCB Layout...........................................................29
7.1 Main Board............................................................29
7.2 Power Board........................................................31
7.3 Key Board.........................................................33
8. Wiring Diagram...................................................34
9. Mechanical Instructions.........................................35
10.Trouble shooting..............................................44
11. Repair Flow Chart...............................................46
12. ISP Instructions......................................................52
13. DDC Instructions...................................................60
15. Monitor Exploded View.........................................74
16. Recommended & Spare Parts List..............................75
17. Different Parts List..............................................86
18. General Product Specification...............................89
Jul. 16, 2007
K
Page
GB
312278517310

Advertisement

Table of Contents
loading

Related Manuals for Philips 150S8FB/00

Summary of Contents for Philips 150S8FB/00

  • Page 1: Table Of Contents

    CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING REFER TO BACK COVER FOR IMPORTANT SAFETY GUIDELINES Published by Philips CE Copyright reserved Subject to modification ○ Jul. 16, 2007...

  • Page 2: Revision List

    Jul.16, 2007 Initial release, Draft Version Sep.13,2007 Add new BOM in Item 17 Oct.11,2007 Add 12NC for 150S8FB/00 and 150S8FB/93 Nov.24,2007 Add 12NC for 715GT039 A Feb.1,2008 Add new BOM in Item 17 Apr.10,2008 Add new BOM for 150S8FB/78 and 150S8FBJ/78...

  • Page 3: Important Safety Notice

    HUDSON 8 Important Safety Notice Proper service and repair is important to the safe, reliable operation of all Philips Company Equipment. The service procedures recommended by Philips and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose.

  • Page 4: Monitor Specifications

    HUDSON 8 1. Monitor Specifications...

  • Page 5: Lcd Monitor Description

    HUDSON 8 2. LCD Monitor Description The LCD monitor will contain a main board, a power board and a key board which house the flat panel control logic, brightness control logic and DDC. The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.

  • Page 6: Operation Instructions

    HUDSON 8 3. Operating Instructions 3.1 General Instructions Press the power button to turn the monitor on or off. The other control buttons are located at the front of the panel of the monitor. By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected.
  • Page 7 HUDSON 8 Rear View...

  • Page 8: Adjusting The Picture

    Description of the On Screen Display This is a feature in all Philips LCD monitors. It allows an end user to adjust screen performance of the monitors directly through an on-screen instruction window. The user interface provides user-friendliness and ease-of-use when operating the monitor.
  • Page 9 HUDSON 8 The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as a reference when you want to work your way around the different adjustments later on.
  • Page 10 HUDSON 8...
  • Page 11 HUDSON 8...

  • Page 12: Connecting To The Pc

    HUDSON 8 3.4 Connecting to the PC 1) Connect the power cord to the back of the monitor firmly. (Philips has pre-connected) VGA cable for the first installation. 2) Connect to PC (a) Turn off your computer and unplug its power cable.

  • Page 13: Input/Output Specification

    HUDSON 8 4. Input/ Output Specification 4.1 Input Signal Connector Analog connectors Pin No. Description Pin No. Description Red video input DDC +5V Green video input Logic Ground Blue video input Ground Sense (GND) Serial data line (SDA) Cable detect (GND) H.

  • Page 14: Pixel Defect Policy

    HUDSON 8 4.3 Pixel Defect Policy...
  • Page 15 HUDSON 8...
  • Page 16 HUDSON 8...

  • Page 17: Failure Mode Of Panel

    HUDSON 8 4.4 Failure Mode Of Panel Quick reference for failure mode of LCD panel this page presents problems that could be made by LCD panel. It is not necessary to repair circuit board. Simply follow the mechanical Polarizer has bubbles instruction on this manual to eliminate failure by replace LCD panel.

  • Page 18: Block Diagram

    HUDSON 8 5. Block Diagram 5.1 Software Flow Chat...
  • Page 19 HUDSON 8 1) MCU initialize. 2) Is the EPROM blank? 3) Program the EPROM by default values. 4) Get the PWM value of brightness from EPROM. 5) Is the power key pressed? 6) Clear all global flags. 7) Are the AUTO and SELECT keys pressed? 8) Enter factory mode.

  • Page 20: Electrical Block Diagram

    HUDSON 8 5.2 Electrical Block Diagram 5.2.1 Main Board Panel Interface (CN404) Scalar NT68623MEFG EEPROM Keypad Interface (Include MCU, ADC, OSD) AT24C16AN (CN403) (U401) (U403) H sync Crystal V sync 12.000MHZ VGA_SDA, (X401) VGA SCL D-Sub Connector (CN405) EEPROM M24C02 (U405)
  • Page 21 HUDSON 8 5.2.2 Power/ Inverter Board...

  • Page 22: Schematic Diagram

    HUDSON 8 6. Schematic 6.1 Main Board 715G1711-1 ADC Input MCU-VDD R485 1K 1/10W C409 0.1uF 16V CN405 VGA-5V DB15 ZD408 CN405 A2 R441 R426 UDZS5.6B 220 1/10W 1K 1/10W GND_A D406 C402 C4 BAV99 C409 A5 VGA-SCL VGA-DET C410 B5 FB401 GND_A C411 C5...
  • Page 23 HUDSON 8 NT68623 MCU-VDD LEDG Q402 R418 10K 1/10W TCLK1M 2N3906S-RTK/PS TCLK1P LED-Green R437 200 1/10W RSTn Q404 R419 10K 1/10W LEDA IRQn 2N3906S-RTK/PS CN401 G6 CN402 G4 LED-Orange R438 200 1/10W CN403 G2 C401 D3 CVDD1V8 C403 E3 C404 E3 DVDD C405 D3 C406 D3...
  • Page 24 HUDSON 8 PANEL OUTPUT LVDS CN404 OUTPUT CN404 A3 C423 C4 C424 C3 TCLK1M TCLK1P C425 C2 C432 C3 FB409 C4 TCLK1P FB410 C3 TCLK2M TCLK2P TCLK1M Q405 C3 Q406 C2 R403 C2 LCD-VDD LCD-VDD R414 C1 R417 C2 R444 C4 CONN GND_A GND_A...
  • Page 25 HUDSON 8 FB703 120 OHM DVDD U701 FB704 120 OHM OUTPUT INPUT 403mA CONNECTOR FOR ADC_VAA POWER/INVERTER +12V BOARD 2.0 mm C701 C707 C705 C713 1000pF 50V 10uF/16V 0.1uF 16V C709 1000pF 100uF/25V CN701 B5 R701 47 1/10W FB701 CN702 120 OHM PANEL_IDX BL-ON...

  • Page 26: Power Board

    HUDSON 8 6.2 Power Board 715G1676-1 POWER R922 100 1/8W R923 100 1/8W C914 1000pF 10% Y5P 500V R924 100 1/8W L903 DB901 R904 BRIDGE KBP206G 2A 600V R907 +12V 430K 1/8W 510K 1/8W C916 D904 C917 470uF/25V C905 C904 R910 T901 SP10150...
  • Page 27 HUDSON 8 INVERTER R801 CN801 +12V T801 T801 CN801 A8 CN802 B8 C801 B2 C803 F6 1/8W C804 E3 C805 E3 R802 R804 R805 C806 D4 C807 D6 C816 1/8W C808 F6 C809 D6 300K 1/10W 1/10W 15pF/6KV LM323-B1-TF-2 C810 D6 C811 A4 C812 F6 C814 B5...

  • Page 28: Key Board

    HUDSON 8 6.3 Key Board 715G1755-2 CN101 CONN LED-G LED-O KEY2 R101 100R 1/10W 5% K-PWR K-PWR KEY1 R100 KEY2 0R05 1/8W CN101 A1 add on Mar.-31-07 KEY1 C101 A1 C101 C102 C103 C104 C105 C102 A1 0.01uF 0.01uF 0.01uF 0.01uF 0.01uF C103 A1...

  • Page 29: Pcb Layout

    HUDSON 8 7. PCB Layout 7.1 Main Board 715G1711-1 C401 C435 D404 R410 R448 C402 C436 D405 R411 R449 C403 C437 D406 R412 R450 C404 C438 D416 R414 R451 C405 C439 FB401 C3 R415 R452 C406 C440 FB402 C3 R417 R453 C407 C441...
  • Page 30 HUDSON 8...

  • Page 31: Power Board

    HUDSON 8 7.2 Power Board 715G1676-1 C802 C2 J903 C3 C811 B2 J904 B3 C816 C1 J905 C3 C901 D3 J906 B3 C902 D3 J907 A3 C903 C2 J908 A2 C904 C3 J909 A2 C905 C4 J911 A4 C910 C3 J912 A3 C914 B3 J913 B4 C915 A4 J914 A2 C916 A3 J915 A2...
  • Page 32 HUDSON 8 C801 A2 R816 B1 C803 A2 R817 B1 C804 B2 R818 C1 C805 B2 R819 D1 C806 A2 R820 B1 C807 B1 R821 B2 C808 D1 R822 A2 C809 B1 R824 B1 C810 B1 R825 B1 C812 A2 R826 D1 C814 B2 R827 D1 C815 D1 R828 D1 C818 B2 R829 A2...

  • Page 33: Key Board

    HUDSON 8 7.3 Key Board 715G1755-2 CN101 A1 LED1 A3 SW1 A5 SW2 A4 SW3 A4 SW4 A4 SW5 A3 SW6 A3 SW7 A3 SW8 A2 C101 A1 C102 A1 C103 A4 C104 A3 C105 A4 R100 A4 R101 A4 R102 A4 R103 A4 R104 A4...

  • Page 34: Wiring Diagram

    HUDSON 8 8. Wiring Diagram Lamp Wire Harness Panel Lamp Wire Harness Power Wire Harness CN801 Panel Interface CN902 CN701 CN404 Power Board Main Board CN901 CN802 CN403 CN101 D-SUB AC-IN Key Board Wire CN101 Key Board...

  • Page 35: Mechanical Instructions

    HUDSON 8 9. Mechanical Instructions 1. Back View as Fig1 Place the monitor face down on a smooth surface as Fig 1. Be careful to avoid scratch and injury during the uninstallation. Fig1 2. Remove the cable management as Fig2. Fig2...
  • Page 36 HUDSON 8 3. Remove the stand & base as Fig3. Fig3 4. Remove rear cover as Fig4~Fig6 a. Remove 2 screws to remove rear cover as Fig4. b. Use plastic putty knife to release 3 snaps on the bottom as Fig. 5. Fig4...
  • Page 37 HUDSON 8 3 snaps on the bottom Plastic putty knife Fig5 c. Insert plastic putty knife into the gap between front bezel and rear cover to release 3 snaps on the left, 3 snaps on the right and 4 snaps on the top as Fig6~Fig9. Front Bezel Rear cover Fig6...
  • Page 38 HUDSON 8 3 snaps on the right Fig8 4 snaps on the top Fig9 5. Remove shielding as Fig10 Remove 8 screws as Fig10~Fig12. Fig10...
  • Page 39 HUDSON 8 Fig11 Fig12...
  • Page 40 HUDSON 8 6. Remove main board and power board as Fig13~Fig14. Remove 3 screws & 5 interfaces to remove main board and power board as Fig13~Fig14. Fig13 Fig14...
  • Page 41 HUDSON 8 7. Remove the bezel as Fig15- Fig18 a. Loose 3 clips at the top of the main frame as Fig15. b. Loose 3 clips at the bottom of the main frame as Fig16. c. Loose 2 clips at the right of bezel as Fig17. d.
  • Page 42 HUDSON 8 Fig17 Fig18 8. Remove the main frame as Fig19- Fig20. a. Remove 2 screws at the left of main frame Fig19. b. Remove 2 screws at the right of the main frame Fig20. Fig 19...
  • Page 43 HUDSON 8 Fig 20 9. The end as Fig21. Fig 21...

  • Page 44: Trouble Shooting

    HUDSON 8 10. Trouble Shooting This page deals with problems that can be corrected by a user. If the problem still persists after you have tried these solutions, contact Philips customer service representative.
  • Page 45 HUDSON 8...

  • Page 46: Repair Flow Chart

    HUDSON 8 11. Repair Flow Chart 11.1 Main Board (1). No Power No power Press power key and look if the picture is normal Please reinsert and make sure the AC of 100-240 is normal Reinsert or check the Adapter/Inverter section Measure U702 PIN2=1.8V Replace U702...
  • Page 47 HUDSON 8 (2). No Picture No picture Measure U702 PIN2=1.8V Replace U702 X401 oscillate waveforms are normal Replace X401 Check if the sync signal from computer is output and video cable Input the sync signal of computer, or change Replace U401...
  • Page 48 HUDSON 8 (3). White screen White screen Measure Q406 base X401 oscillate waveform is normal is high level? Replace X401 Check Q406, Q405 is broken or CN404 solder? Check Correspondent component. Check Correspondent component. Replace Panel...
  • Page 49 HUDSON 8 11.2. Power/Inverter Board (1) No power Check CN902 pin7 = 12V Check AC line volt 110V or 220V Check AC input Check the voltage of C905 (+) Check bridge rectified circuit and F901 circuit Check start voltage for the pin3 of IC901 Check R904, R905 and R906 or change IC901 Check the auxiliary voltage is bigger than 10V and smaller than 20V...
  • Page 50 HUDSON 8 (2) No backlight Check C811 (+) =12V Check adapter board Check ON/OFF signal Check Interface board or main board Check IC801 pin 2=5V? Check Q801, Q802, Q803, ZD801 Check IC801 Pin1/pin15 have the output of sawtooth wave at short time Check IC801 pin 5/pin6 Replace IC801 Check Q805 pin5/pin8 is 12V?
  • Page 51 HUDSON 8 11.3 Key Board OSD is unstable or not working Connect Key Pad Board Is Key Pad Board connecting normally? Replace Button Switch Is Button Switch normally? Replace Key Pad Board Is Key Pad Board normally? Check Main Board...

  • Page 52: Isp Instructions

    HUDSON 8 12. ISP Instruction (1). Install the program software First decompressing files , as follow:...
  • Page 53 HUDSON 8 b. Double – click , start to install as follows:...
  • Page 54 HUDSON 8...
  • Page 55 HUDSON 8...
  • Page 56 HUDSON 8 c. There will be a shortcut key appears on the desktop. (2). Connect the ISP board as follow: Connect to the Connect to Philips 150S8 the PC LPT a. Double-click ，running the program as follows:...
  • Page 57 HUDSON 8 b. Click icon, search the program” PHILIPS_150S8_LPL_LM150X08_TLC1_AP_V2.00.HEX”, and click open: c. Select MUC name “NT68663/623-128K (128K)”...
  • Page 58 HUDSON 8 d. Click icon, the writer is in processing…...
  • Page 59 HUDSON 8 e. Until appears the follow Fig, writer completed.

  • Page 60: Ddc Instructions

    HUDSON 8 13. DDC Instruction General DDC Data Re-programming In case the main EEPROM with Software DDC which store all factory settings were replaced because a defect, repaired monitor’ the serial numbers have to be re-programmed. It is advised to re- soldered the main EEPROM with Software DDC from the old board onto the new board if circuit board have been replaced, in this case the DDC data does not need to be re-programmed.
  • Page 61 HUDSON 8...
  • Page 62 HUDSON 8...
  • Page 63 HUDSON 8...
  • Page 64 HUDSON 8 Click to complete the installation. Note: After installation, you must restart the PC to take the setup to effect.
  • Page 65 HUDSON 8 2. Install the “WinDDC_ setup” Second, you must install the . The processing as follows:...
  • Page 66 HUDSON 8...
  • Page 67 HUDSON 8 Click to complete the installation. 3. Connect the DDC board as follow: Connect to the PC LPT When you write analog EDID, Connect this port to the Philips 150S8’s VGA port 12V Input...
  • Page 68 HUDSON 8 4. Take analog DDC write for example, as follow a. Double-click ，appear as follow Figs：...
  • Page 69 HUDSON 8 b. Click c. Key 14 numbers in the Serial Number blank, then click “OK”. Now analog DDC Write completes, as follow.
  • Page 70 HUDSON 8 150S8 EDID 128 bytes EDID Data (Hex): 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 00 FF FF FF FF FF FF 00 41 0C 63 08 EB D9 01 00 16: 20 0B 01 03 0E 1E 17 78 2A 3C 40 9C 56 4D 98 26 32: 16 50 54 BF EE 00 01 01 01 01 01 01 01 01 01 01 48: 01 01 01 01 01 01 64 19 00 40 41 00 26 30 18 88...
  • Page 71 HUDSON 8 Composite Sync Support: Yes Sync. on green video supported:Yes Serration of the Vsync.Pulse is not required. Max. H. Image Size : 30cm. Max. V. Image Size : 23cm. Display Gamma: DPMS Features, Active off: Yes. Display Type: R/G/B color display. Preferred Timing Mode: Yes.
  • Page 72 Detailed Timing: 1024x768 @ 60Hz. <-x-Detailed Timing Descriptions-x-> <---Detailed Timing Descriptions---> Detailed Timing: FF (Monitor SN) '132313212132' Detailed Timing: FC (Monitor Name) 'Philips 150S' Detailed Timing: FD (Monitor limits) Min. V. rate: 56Hz Max. V. rate: 76Hz Min. H. rate: 30KHz Max.

  • Page 73: White Balance, Luminance Adjustment

    HUDSON 8 14. White Balance, Luminance Adjustment Approximately 30 minutes should be allowed for warm up before proceeding White-Balance adjustment. 1. Required instruments: Chroma 7120、Chroma 2325（BGA265A） 。 2. First connect the instruments together and turn on the LCD power. 3.Set Chroma 2325（BGA265A）to be T139 (1024*768/60HZ）and P105 of full white screen. 4．Enter into the factory mode: Firstly, turn off the power, press the AUTO and OK at one time, and then turn the power on (AUTO and OK are still pressed, about 10s), release, press the menu again will activate the factory mode, the factory OSD will be...

  • Page 74: Monitor Exploded View

    HUDSON 8 15. Monitor Exploded View...

  • Page 75: Recommended & Spare Parts List

    HUDSON 8 16. Recommended & Spare Parts List Recommended Parts List 150S8FB/93 Item Location Part No. Description Philips 12NC FQ006 P34G1827 VBC1T BEZEL 996510006498 FQ004 P33G4971 VQA1C BUTTON_OSD 996500036889 FQ007 P34G1828 VB 1T REAR COVER 996500035924 FQ005 P33G4972 VB 1L...
  • Page 76 HUDSON 8 Spare Parts List Service Kit Description Part No. Philips 12NC Remark DDC Kit 715L2005C2 9965 000 43197 for all model OSD SN Kit 715GT033 C 9965 000 43252 for all model for all hudson 7 NOVATEK ISP Kit...
  • Page 77 HUDSON 8 Accessory and Mechanical Location Part No. Description Philips 12NC FQ001 089G 728TAA550 SIGNAL CABLE D-SUB TONGFU 996510006491 FQ014 089G404A18N IS POWER CORD 996500037422 FQ002 095G8014 10528 WIRE HARNESS 996510006492 FQ003 750GLG50X8C12M000F PANEL LM150X08-TLC1 LPL 996510006493 FQ004 P33G4971 VQA1C...
  • Page 78 HUDSON 8 Board Parts Location Part No. Description Philips 12NC FQ017 CBPC7GNMPHQE SCALER BOARD ASSY 996510006502 C401 065G040210232T 0402 MLCC 1000PF K 50V 996500035987 C402 065G040210131T 0402 MLCC 100PF J 50V 996500035986 C403 065G040247312T 0402 MLCC 47NF K 16V 996500035991...
  • Page 79 D406 093G 64 33 DIO SIG SM BAV99 (PHSE)R 996500035994 D416 093G 64 42 PP BAV70 SOT-23 996500035995 Q401 057G 417 4 PMBS3904/PHILIPS-SMT(04) 996500035966 Q402 057G 417 13 T KEC 2N3906S-RTK/PS 996500035967 Q404 057G 417 13 T KEC 2N3906S-RTK/PS 996500035967...
  • Page 80 HUDSON 8 R421 061G0603151 RST CHIP 150R 1/10W 5% 996500045269 R422 061G0603102 RST CHIP 1K 1/10W 5% 996500040053 R423 061G0603151 RST CHIP 150R 1/10W 5% 996500045269 R424 061G0603151 RST CHIP 150R 1/10W 5% 996500045269 R426 061G0603102 RST CHIP 1K 1/10W 5% 996500040053 R427 061G0603102...
  • Page 81 HUDSON 8 CRYSTAL 12MHz HC-49US X401 093G 22 51 ARG6-120 996500035961 CN405 088G 35315F H D-SUB 15PIN 996500035960 FB401 061G0603000 RST CHIPR 0 OHM -5% 1/10W 996500042212 FB402 061G0603000 RST CHIPR 0 OHM -5% 1/10W 996500042212 FB403 061G0603000 RST CHIPR 0 OHM -5% 1/10W 996500042212 FB404 061G0603000...
  • Page 82 HUDSON 8 LED1 081G 12 1F GP LED GP32032M/G307-ZY-50 996510006457 R100 061G0805000 0 OHM 1/10W 996500042284 R101 061G0603101 RST CHIPR 100 OHM -5% 1/10W 996500042213 R102 061G0603473 RST CHIPR 47 KOHM -5% 1/10W 996500042277 R103 061G0603103 RST CHIPR 10 KOHM -5% 1/10W 996500042214 R104 061G0603102...
  • Page 83 CHOKE COIL 996500036026 L904 073G 253 91 H CHOKE COIL 996500036026 Q801 057G 759 2 RK7002 996500036033 Q802 057G 417 4 PMBS3904/PHILIPS-SMT(04) 996500035966 Q803 057G 417 4 PMBS3904/PHILIPS-SMT(04) 996500035966 Q804 057G 759 2 RK7002 996500036033 Q805 057G 763 14 AM9945N...
  • Page 84 HUDSON 8 R808 061G1206104 RST CHIPR 100 KOHM +-5% 1/4W 996510006535 R809 061G0805105 1MOHM 1/10W 996500043382 R810 061G0805100 3F RST CHIPR 100KOHM +-1% 1/8W 996510006227 R811 061G0805750 2F RST CHIPR 75 KOHM +-1% 1/8W 996510006532 R812 061G0805100 2F RST CHIPR 10KOHM -1% 1/8W 996500044853 R813 061G0805105...
  • Page 85 HUDSON 8 R920 061G152M688 64 0.68OHM -5% 2W 996500036011 R922 061G1206101 100 1206 996500045142 R923 061G1206101 100 1206 996500045142 R924 061G1206101 100 1206 996500045142 R925 061G1206101 100 1206 996500045142 R926 061G1206101 100 1206 996500045142 R927 061G1206101 100 1206 996500045142 R928 061G0805100 1F RST CHIPR 1KOHM +-1% 1/8W 996510006226...

  • Page 86: Different Parts List

    HUDSON 8 17. Different Parts List Diversity of 150S8FB/00 compared with 150S8FB/93 150S8FB/00 150S8FB/93 Location Part No. Description Philips 12NC Part No. Description Philips 12NC FQ014 089G404A18N IS POWER CORD 996510003520 089G414A18N IS POWER CORD 996500037422 FQ006 P34G1827 VBD1T BEZEL...
  • Page 87 HUDSON 8 Diversity of 150S8FS/78 compared with 150S8FB/93 150S8FS/78 150S8FB/93 Location Part No. Description Philips 12NC Part No. Description Philips 12NC FQ020 044G6000 4E CARTON E08901 089G402A18NIS1 POWER CORD FQ004 P33G4971 VPA1C BUTTON_OSD P33G4971 VQA1C BUTTON_OSD 996500036889 FQ006 P34G1827 VOD1T...
  • Page 88 HUDSON 8 Diversity of 150S8FB/78 compared with 150S8FB/93 150S8FB/78 150S8FB/93 Location Part No. Description Philips 12NC Part No. Description Philips 12NC E08901 089G402A18NIS1 POWER CORD 089G414A18N IS POWER CORD 996500037422 FQ106 P34G1827 VBD1B BEZEL(15") P34G1827 VBC1T BEZEL 996510006498 FQ105 P34G1828 VB 2B REAR COVER(15")

  • Page 89: General Product Specification

    MECHANICAL CHARACTERISTICS 5.1 COSMETIC PHILIPS ID 5.2 MECHANICAL DATA FILES PROE FILES REQUIRED 5.3 LOCATION OF PHILIPS LOGO PER PHILIPS MAKE-UP SHEET 5.4 GAP BETWEEN PANEL AND FRONT BEZEL <1.2 MM 5.5 LOCATION OF CONTROL ICONS PER PHILIPS GRAPHIC SHEET 5.6 COLOR FOR RESIN/PAINT...
  • Page 90 6.3 DISPLAY DISTURBANCES TO EXTERNAL ENVIRONMENT RELIABILITY 7.1 MEAN TIME BETWEEN FAILURES QUALITY ASSURANCE REQUIREMENTS 8.1 ACCEPTANCE TEST 9. SERVICEABILITY PHILIPS’ FLAT PANEL MONITORS PIXEL DEFECT POLICY REGULATORY COMPLIANCE 11.1 WORLDWIDE REGULATORY 11.2 EMC REQUIREMENTS 11.3 ROHS 11.4 WEEE 11.5 ONGOING REGULATORY...

  • Page 91: Foreword

    30 minutes that brightness stability is optimal, and follow strictly after panel specification. 2. PRODUCT PROFILE This display monitor unit is a color display monitor enclosed in PHILIPS global styling cabinet, which has an integrated tilt base. 2.1 LCD Type NR.

  • Page 92: Interface

    HUDSON 8 Composite sync TTL level, input impedance 5k ohm terminate (Positive/Negative) Sync on green video 0.3 Vp-p Negative (Video 0.7 Vp-p Positive) 2). DVI-D Digital：NA 3.2 Interface 3.2.1 D-Sub Cable Length : 1.8 M +/- 50 mm Fix with monitor when packing, with transplant pin protective cover. Connector type : D-Sub male with DDC2B pin assignments.

  • Page 93: Timing Requirement

    HUDSON 8 3.3 Timing requirement 3.3.1 Mode storing capacity Factory preset modes : 13 Preset modes : 18 3.3.2 Factory preset timings Item H.Freq. (KHz) Mode Resolution V.Freq. (Hz) 31.469 IBM VGA 3H 720x400 70.087 31.469 VESA 640x480 59.940 37.861 VESA 640x480 72.809...
  • Page 94 HUDSON 8 3.3.3 Preset Modes MODE NO. RESOLUTION 640 x 350 720 x 400 640 x 480 640 x 480 Dot clock(MHz) 25.175 28.321 25.175 30.24 31.469kHz 31.468kHz 31.5kHz 35 kHz A ( us ) 31.778(800 dots) 31.78(900dots) 31.778(800 dots) 28.571 (864 dots) B ( us ) 3.813(96 dots)
  • Page 95 HUDSON 8 MODE NO. RESOLUTION 800 x 600 800 x 600 800 x 600 800 x 600 Dot clock(MHz) 49.498 56.251 37.9kHz 48.077kHz 46.9kHz 53.7kHz A ( us ) 26.4 (1056 dots) 20.80 (1040dots) 21.333 (1056dots) 18.631 (1048 ots) B ( us ) 3.2 ( 128 dots) 2.400 ( 120 dots) 1.616 ( 80 dots)
  • Page 96 HUDSON 8 MODE NO. RESOLUTION 1024 x 768 1024 x 768 Dot clock(MHz) 83.096 94.5 61.1kHz 68.7kHz A ( us ) 16.367 (1360dots) 14.561(1376 dots) B ( us ) 1.348 ( 112 dots) 1.016( 96 dots) C ( us ) 2.022 ( 168 dots) 2.201 ( 208 dots) D ( us )

  • Page 97: Horizontal Scanning

    HUDSON 8 3.4 Horizontal scanning Sync polarity : Positive or Negative Scanning frequency : 30 – 63 K Hz 3.5 Vertical scanning Sync polarity : Positive or Negative Scanning frequency : 56 - 76 Hz 3.6 Power input connection Power cord length : 1.8 M Power cord type : 3 leads power cord with protective earth plug.

  • Page 98: Brightness Uniformity

    HUDSON 8 4.4 Brightness uniformity Set contrast at 100% and turn the brightness to get average above 200 nits at centre of the screen. Apply the Fig 1, it should comply with the following formula: B_min X 100% >75% B_max Where B_max =Maximum brightness, B_min = Minimum brightness 4.5 Check Cross talk (S) Apply Pattern 2.

  • Page 99: Mechanical Characteristics

    All major plastic parts (bezel, back cover, base) need to be molded from same resin. 5.11 Texture/Glossing of housing The texture area and texture no should follow Philips make-up sheet. The exterior surfaces shall have a uniform texture. Philips must approve the mold texturing.

  • Page 100: Transportation

    HUDSON 8 5.15 Transportation Transportation standards refer to TYE-M0002. 5.15.1 Transportation packages Packaging and wrapping shall be sufficient to protect the product against damage or loss during shipment from the supplier to the destination specified in the purchase order. All packaging materials are subject to test and evaluation per TYE-M0002.

  • Page 101: Pallet/Container Loading

    HUDSON 8 5.16 Pallet / Container loading Except China China Transportation standards refer to TYE-M0002. Pallet Slip sheet Pallet Slip sheet • Air shipment - 54 sets 48 sets • Sea container 20'(pallet/slip sheet) - • Sea container 40'(pallet/slip sheet) - 1820 1950 1680...

  • Page 102: Serviceability

    HUDSON 8 9. Serviceability The serviceability of this monitor should fulfill the requirements which are prescribed in UAW-0346 and must be checked with the check list UAT-0361. 10. Philips’ Flat Panel Monitors Pixel Defect Policy BRIGHT DOT DEFECTS ACCEPTABLE LEVEL MODEL...
  • Page 103 HUDSON 8 Fig 1: Brightness Uniformity Fig 2: Cross talk pattern Gray level 46 (64 Gray level) Fig 3: Cross talk Pattern Center at Gray level 0 (Black)
  • Page 104 HUDSON 8 SEPARATE SYNC. VIDEO HORIZONTAL VIDEO VERTICAL COMPOSITE SYNC. VIDEO HORIZONTAL FIG-4 TIMING CHART -1...

  • Page 105: Regulatory Compliance

    HUDSON 8 11. REGULATORY COMPLIANCE 11.1 Worldwide Regulatory Domain Safety / EMC / Ergonomics / Standards Documents Country CB Report IEC60950-1:2001. Group -and national differences International and CB of all countries listed in CB Bulletin No. 107A certificate European Low Voltage Directives 73/23/EEC and Declaration of 93/68/EEC Conformity...
  • Page 106 HUDSON 8 Certificate of South Africa SABS IEC 60950 Conformity UL 60950-1: 2003 UL certificate FCC Part 15 Class B FCC ID grant Energy Star registration CSA C22.2 No 60950 CSA certificate Canada Statement on ICES-003 issue 3 label Mexico NOM-019-SCFI-1994 certificate Korean Safety Control law IEC 60950...

  • Page 107: Emc Requirements

    11.2 EMC Requirements Supplier DVT EMI test result must be submitted prior to DVT samples delivery, and PVT EMI test result must be submitted again prior to PVT samples delivery, which also has to meet Philips' immunity testing specification. 11.3 RoHS Restriction on the use of certain hazardous substances.

This manual is also suitable for:

150s8fb/93150s8fs/00150s8fb/78150s8fbj/78150s8fs/78

Table of Contents