Black & Decker PI102PP Instruction Manual

PI102PP ManualEN 072308.qxp 7/23/2008 10:04 AM Page 6
For safety reasons, the unit will simply shut down if it is overloaded. To restart the unit, simply remove the
load, wait a few minutes, then plug it back in, rotating slightly to make sure there is good contact.
Operation of the 115 Volt AC Outlet
1. Connect the unit to a vehicle's accessory outlet or other 12 volt DC power source. Make sure there is
adequate space for proper ventilation of the inverter.
2. Rotate the unit slightly to make sure there is good contact.
3. The Power/Fault LED Indicator will light green, indicating a proper connection. If the Power/Fault LED
Indicator lights red, a Fault condition exists. Refer to the Troubleshooting Section of this Instruction
Manual.
4. If the Inverter does not work, make sure the ignition/accessory outlet is powering the accessory outlet.
Some vehicles require the ignition switch to be turned on.
5. Plug the (110/120 volt AC) appliance into the Inverter's three-prong AC outlet and operate normally.
Notes: The Inverter will not operate appliances and equipment that generate heat, such as hair dryers,
electric blankets, microwave ovens and toasters.
Remember to disconnect the unit from any power source when it is not in use.
Operation of the USB Charging Port
1. Connect the unit to a vehicle's accessory outlet or other 12 volt DC power source. Make sure there is
adequate space for proper ventilation of the inverter.
2. Rotate the unit slightly to make sure there is good contact.
3. The Power/Fault LED Indicator will light green, indicating a proper connection. If the Power/Fault LED
Indicator lights red, a Fault condition exists. Refer to the Troubleshooting Section of this Instruction
Manual.
4. If the Inverter does not work, make sure the ignition/accessory outlet is powering the accessory outlet.
Some vehicles require the ignition switch to be turned on.
5. Plug the USB-powered device into the inverter's USB Charging Port and operate normally.
Notes: This inverter's USB Charging Port does not support data communication. It only provides 5 volts
DC/500 mA (5 volts DC/200 mA when combined with inverter AC output over 90W) power to an
external USB-powered device.
Remember to disconnect the unit from any power source when it is not in use.
Protective Features
The inverter monitors the following conditions:
Low Battery Voltage — This condition is not harmful to the inverter, but could damage the power source, so
the inverter will automatically shut down when input voltage drops below 10.5 ± 0.3 volts DC.
Input Voltage Too High — The inverter will automatically shut down when DC input voltage exceeds 15.5 ±
0.3 volts, as this can harm the unit.
Thermal Shutdown Protection — The inverter will automatically shut down when the unit becomes
overheated.
Overload/Short Circuit Protection — The inverter will automatically shut down when a short circuit occurs.
Notes: The Power/Fault LED Indicator will light red to indicate a Fault condition before automatic shutdown
occurs.
If unit shuts down, disconnect it from the 12 volt DC power source, remove the load, wait a few
minutes, then plug it back in, rotating slightly to make sure there is good contact.
Operating Tips
The inverter should only be operated in locations that are:
DRY — Do not allow water or other liquids to come into contact with the inverter.
COOL — Surrounding air temperature should ideally be 10-20°C (50-68°F). Keep the inverter away from
direct sunlight, when possible.
WELL-VENTILATED — Keep the area surrounding the inverter clear to ensure free air circulation around the
unit. Do not place items on or over the inverter during operation. The unit will shut down if the internal
temperature gets too hot. The inverter will auto-reset after it cools down.
6
SAFE — Do not use the inverter near flammable materials or in any locations that may accumulate
flammable fumes or gases. This is an electrical appliance that can briefly spark when electrical connections
are made or broken.
Important:
During engine cranking the voltage will drop below 10.5V and therefore shutdown the inverter. To reset the
unit, disconnect it from the 12 volt DC power source, leave for a few seconds and then plug it back in once
the engine has started.
CARE AND MAINTENANCE
Storage
1. Ideal storage temperature range is 0-40°C (32-104°F).
2. Store and use the inverter in a cool, dry place with adequate ventilation for all-around air circulation.
3. Avoid locations that are exposed to heating units, radiators, direct sunlight, or excessive humidity or
dampness.
TROUBLESHOOTING
Common Audio Problems
Problem Explanation/Recommendation
Buzzing sound in audio systems Some inexpensive stereo systems and boom boxes make a buzzing
sound when operated from the inverter, because the power supply in
the electronic device does not properly filter the modified sine wave
produced by the inverter. The only solution to this problem is to use
a sound system that has a higher quality power supply.
Common Power Output Problems
Possible Cause Recommendation
Battery voltage below 10.5 volts Recharge battery or check DC power supply.
Equipment being operated draws Reduce load to maximum 100 watts.
too much power
Inverter in thermal shutdown Allow inverter to cool down. Ensure there is adequate ventilation
condition around the load is no more than 100 watts for continuous operation.
AC output is shorted Unplug the AC appliance. Disconnect the unit from any 12 volt DC
power source. Check the appliance cord. Refer to the Service
Information section that follows to contact a Black & Decker Service
Center.
Power/Fault LED Indicator Lights Red
When the Power/Fault LED Indicator turns from green (indicating the unit is powered) to red, a fault
condition is present and the unit will automatically shut down. See the Protective Features Section of this
Instruction Manual and Common Power Output Problems in the following section.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or authorized service
center. If you need assistance regarding accessories, please call: 1-800-544-6986.
WARNING: The use of any accessory not recommended for use with this tool could be
hazardous.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and
reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts,
contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page
directory under "Tools—Electric" or call: 1-800-544-6986 or visit www.blackanddecker.com.
7
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or
workmanship. The defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was
purchased (provided that the store is a participating retailer). Returns should be made within the time period
of the retailer's policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be
required. Please check with the retailer for their specific return policy regarding returns that are beyond the
time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service
Center for repair or replacement at our option. Proof of purchase may be required. Black & Decker owned
and authorized Service Centers are listed under "Tools-Electric" in the yellow pages of the phone directory
and on our website www.blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have
other rights which vary from state to state or province to province. Should you have any questions, contact
the manager of your nearest Black & Decker Service Center. This product is not intended for commercial
use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-
544-6986 for a free replacement.
SPECIFICATIONS
Output Power: 100 watts continuous
DC Input: 13.8 volts DC, 8 amps
AC Output: 100 watt continuous output –
115V AC @13.8V DC, 60 Hz
USB Charging Port Output: 5 volts DC/500 mA
Fuse: 10 amp internal fuse
Output Waveform: Modified Sine Wave
Optimum Efficiency: >85%
Low Voltage Shutdown: <10.5 ± 0.3 volts input voltage
Operating Temperature: 10-20°C (50-68°F)
Storage Temperature: 0-40°C (32-104°F)
Operating/Relative Humidity: 5-95% non-condensing
Imported by
See 'Tools-Electric'
Black & Decker (U.S.) Inc.,
– Yellow Pages –
01 E. Joppa Rd. for Service & Sales
Towson, MD 21286 U.S.A.
RD072308
8
100 WATT POWER INVERTER
WITH USB CHARGING PORT
INSTRUCTION MANUAL
Catalog Number PI102PP
Thank you for choosing Black & Decker!
Go to www.BlackandDecker.com/NewOwner
to register your new product.
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
BEFORE YOU CALL, HAVE THE CATALOG No, AND DATE CODE
AVAILABLE. IN MOST CASES, A BLACK & DECKER
REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE
PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US
A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Catalog # PI102PP Form # 90536264
July 2008 Copyright © 2008 Black & Decker Printed in China
1