Get support at http://www.philips.com/support/ http://philips.supportsystem.com/ CMND & Calibrate CCK4602 User Manual Version: 1.0.6 Date: 26 July 2017 Author: Vincent Storm...
Version history: Version Date Author Changes: First rework 1.0.1 02/06/2017 Vincent Storm Layout change 1.0.2 27/06/2017 Vincent Storm Correction in chapter numbering Adding General information Add bold text in Connect COM-port cable 1.0.3 26/07/2017 Vincent Storm ...
Table of Contents Version history: ............................1 General information ........................3 Introduction ..........................3 Notice ............................3 Help and support ........................3 System requirements ........................4 Package content ..........................4 Software installation ........................4 Specifications ..........................5 Calibrated parameters ......................5 Supported tiling matrix ......................
TP Vision Belgium NV cannot be held responsible neither for any errors in the content of this document nor for any problems as a result of the content in this document. Errors reported to Philips will be adapted and published on the Philips support website as soon as possible.
2. System requirements Windows 7 (32-bit/64-bit) or Windows 10 (32-bit/64-bit) DVI / HDMI or DP out An available RS232 port (USB to RS232 adaptor will also work) Free memory : 1 GB Hard disk space : 400MB ...
6. Start the color calibration Before you start the calibration warm up the monitor(s) for minimum 1 hour. Movie of a 2x2 color calibration 6.1 Connect color sensor 1. Lift up the diffuser arm 2. Rotate the diffuser 3. Click the diffuser in the rear position 4.
6.2 Connect COM-port cable Connect the COM-port from your PC via a null modem (= cross) RS232 cable to the RS232 jack 2.5mm input of the first monitor with monitor ID=1. Make sure all the monitors are daisy chained via RS232 ...
6.5 Run the calibration software 6.5.1 Start the program Before you start the calibration warm up the monitor(s) for minimum 1 hour Start the calibration software CMND & Calibrate 6.5.2 Installation tab In the “Installation” tab select your COM-port number ...
6.5.3 Setup tab In the “Setup” tab select your matrix: maximum matrix is 15x15 Point structure: how many points must be aligned in each monitor, recommended value = 5 Note: On the bottom of the window of the program on PC you might see some error in red, adapt where needed according to the errors.
6.5.4 Calibration tab. In the “Calibrate” tab select “Calibrate”: this will launch the calibration Note: read first below before starting the actual calibration A green spot will appear on the first display Put the color sensor on this green spot and do not take it away ...
Page 12
After the calibration is done the green message “Calibrated” will appear on every calibrated monitor. See below screenshot Note: the monitors in the software calibration tool can be deselected, means those monitors will not be calibrated See below screenshot in red marker as an example, monitor “ID: 1” and “ID: 2” will not be calibrated - 11 -...
Page 13
Set as reference is used to adjust the backlight of 1 monitor measured from another monitor it will also adjust the colors to a target value set in the PC Select in 1 monitor “set as reference”, the light output of this monitor will be measured and used as target value to adjust the other monitor(s) ...
6.5.5 Manual tuning It is possible to adjust each monitor manually, select your monitor and you can change the “backlight”, the Red, Green and Blue colors manually of the selected monitor, see the red marker below. 7. Supported monitors 65BDL3000Q ...
Page 15
BDL6520QL BDL3260EL BDL4260EL BDL4660EL BDL5560EL BDL4765EL Firmware must be at least 1.94 for all above monitors - 14 -...