SAFETY INFORMATION CAUTION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
Page 3
[Important Check Points for Good Servicing] In this manual, procedures that must be performed during repairs are marked with the below symbol. Please be sure to confirm and follow these procedures. 1. Product safety Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by following the safety instructions described in this manual.
1. SPECIFICATIONS General Power source ....................13.2 V DC(10.8 V to 16.0 V allowable) Grounding system ..........................Negative type Backup current ............................. 5 mA or less Weight ................................2.5 kg DVD player System ...................... DVD audio, Compact disc audio system Usable discs ......................
2. EXPLODED VIEWS AND PARTS LIST OTES : • Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. • The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
Page 7
EXTERIOR SECTION PARTS LIST Mark No. Description Part No. Mark No. Description Part No. Connector(CN108) CKM1484 Screw BMZ26P030FTB Connector(CN107) CKS5508 Screw BMZ26P040FTC Screw BMZ30P040FTC Screw PBZ30P060FSN Door CAT2801 Screw PBZ30P060FSN Screw(M2 x 2.5) CBA1624 Terminal(CN402) VNF1084 Terminal(CN403) VNF1084 Flat Cable CDE7993 DSP Unit CWN1324...
Page 9
DVD MECHANISM MODULE SECTION PARTS LIST Mark No. Description Part No. Mark No. Description Part No. Holder Unit CXC4342 DVD Core Unit CWX3344 Terminal(CN1902) CKF1064 Stage Assy(Service) CXX2117 Connector(CN1901) CKS5054 ELV Motor Assy(M2) CXC6380 Connector(CN1201) CKS4840 Screw JFZ20P020FTC ••••• Cam Motor Assy(M1) CXC6379 Screw IMS26P025FTC...
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE) Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST". Large size SCH diagram Guide page FM/AM TUNER UNIT AM : -14 dBs FM : -20 dBs Detailed page CN1201 DOL_SDA...
Page 17
NOTE : Symbol indicates a resistor. Decimal points for resistor No differentiation is made between chip resistors and and capacitor fixed values discrete resistors. are expressed as : Symbol indicates a capacitor. ← No differentiation is made between chip capacitors and ←...
3.6 DVD CORE UNIT(2/2) PE5555A 9.830MHz DVZ-MG6067ZH/UC...
Page 37
DVD CORE UNIT(2/2) CN1601 DVZ-MG6067ZH/UC...
Page 38
- Waveforms Note:1. The encircled number denote measuring pointes in the circuit diagram. 2. Reference voltage VHALF : 1.65 V(TD1,FD1,CRGDRV) : 2 V Center(ANAMONI1) In this waveform, it is seeing on the GND standard. Offset of 1.65 V or 2 V is put in. 1 ANAMONI1 0.2 V/div.
4. PCB CONNECTION DIAGRAM 4.1 TUNER CONTROL UNIT NOTE FOR PCB DIAGRAMS TUNER CONTROL UNIT CAR HARN 1.The parts mounted on this PCB include all necessary parts for several destination. For further information for respective destinations, be sure to check with the schematic dia- gram.
Page 41
SIDE A CAR HARNESS CAR HARNESS CAR HARNESS CN1101 CN107 CN1201 CN901 FRONT DVZ-MG6067ZH/UC...
Page 42
TUNER CONTROL UNIT TESTIN PCL2 DVZ-MG6067ZH/UC...
5. ELECTRICAL PARTS LIST NOTE: Parts whose parts numbers are omitted are subject to being not supplied. • The part numbers shown below indicate chip components. • Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS..) CKS.., CCS.., CSZS..The > mark found on some component parts indicates the importance of the safety factor of the part. •...
Page 52
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. Q 351 (A,68,132) Transistor DTC323TU D 130 (A,143,105) Diode MPG06G-6415G50 Q 352 (A,66,136) Transistor DTC323TU D 131 (A,146,105) Diode MPG06G-6415G50 Q 353 (A,70,119) Transistor DTC323TU D 136 (A,152,95) Diode MPG06G-6415G50 Q 354 (A,68,123) Transistor...
Page 53
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 114 (B,133,76) RS1/16S103J R 267 (B,69,29) RS1/16S3602F R 121 (A,143,94) RS1/16S103J R 268 (B,70,25) RS1/16S3602F R 122 (A,144,97) RS1/16S102J R 269 (A,75,33) RS1/16S473J R 123 (B,143,151) RS1/10S103J R 270 (A,67,32) RS1/16S473J...
Page 54
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 373 (A,56,128) RS1/16S223J R 542 (B,164,54) RS1/16S470J R 374 (A,62,112) RS1/16S101J R 543 (B,168,57) RS1/16S105J R 376 (A,61,112) RS1/16S223J R 544 (A,97,130) RS1/10S223J R 377 (A,63,121) RS1/16S101J R 545 (A,110,142) RS1/16S471J...
Page 55
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 661 (B,118,73) RS1/16S0R0J R 769 (A,92,46) RS1/16S152J R 662 (A,108,83) RS1/16S0R0J R 770 (B,90,48) RS1/16S473J R 666 (A,108,49) RS1/16S102J R 801 (A,149,18) RS1/16S102J R 667 (A,106,49) RS1/16S561J R 802 (A,151,18) RS1/16S102J...
Page 56
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. C 322 (B,65,131) CKSQYB102K50 C 601 (B,125,47) CCSRCH330J50 C 323 (B,68,152) CKSQYB102K50 C 602 (B,120,47) CCSRCH8R0D50 C 324 (B,65,133) CKSQYB102K50 C 604 (B,124,31) CKSRYB104K16 C 325 (B,64,152) CKSQYB102K50 C 605 (B,122,31) CKSRYB104K16...
Page 57
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 218 (A,17,22) RS1/16S102J R 925 (B,50,188) RS1/10S333J R 219 (A,26,17) RS1/16S472J R 926 (B,70,170) RS1/10S101J R 220 (A,25,17) RS1/16S472J R 927 (B,65,176) RS1/10S101J R 221 (B,24,16) RS1/10S681J R 928 (B,67,176) RS1/10S101J...
Page 58
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. IC 1471 (B,20,77) IC PCM1606EG R 1124 (B,29,154) RS1/16SS391J IC 1601 (B,9,85) IC TC7WBD125AFK R 1125 (B,41,151) RS1/16S8R2J IC 1602 (B,13,107) IC TC74VHC08FTS1 R 1129 (B,27,140) RS1/16SS160J IC 1603 (B,43,44) IC TC74VHC08FTS1 R 1130...
Page 59
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 1223 (B,11,44) RS1/16SS271J R 1434 (B,16,98) RS1/16SS473J R 1231 (B,27,36) RS1/16SS682J R 1436 (B,14,98) RS1/16SS473J R 1232 (B,25,37) RS1/16SS682J R 1438 (B,13,95) RS1/16SS472J R 1233 (B,28,38) RS1/16SS682J R 1439 (B,13,88) RS1/16SS100J...
Page 60
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 1653 (B,18,13) RS1/10S0R0J C 1221 (B,9,46) CKSYB475K10 R 1654 (B,20,16) RS1/10S0R0J C 1222 (B,8,22) CKSYB475K10 C 1223 (B,11,22) CKSYB475K10 CAPACITORS C 1224 (B,13,22) CKSYB475K10 C 1225 (B,15,25) CKSYB475K10 C 1111 (B,24,163)
Page 61
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. C 1453 (A,30,74) CEVW100M10 D 1101 (A,49,91) Diode 1SS355 C 1454 (A,35,69) CEVW100M10 D 1102 (A,49,96) Diode 1SS355 C 1455 (A,33,80) CEVW100M10 D 2001 (B,94,36) Diode DAN202U C 1457 (B,31,81) CKSSYB104K10 L 1001...
Page 62
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 1017 (A,75,39) RS1/16SS0R0J R 1507 (A,86,63) RS1/16SS0R0J R 1018 (A,89,37) RS1/16SS105J R 1508 (A,87,60) RAB4CQ101J R 1021 (A,83,39) RS1/16SS122J R 1509 (A,87,58) RS1/16SS0R0J R 1101 (A,61,90) RS1/16S6R8J R 1511 (A,90,60) RAB4CQ101J...
Page 63
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 1604 (B,120,60) RS1/16SS0R0J R 1924 (B,26,33) RS1/16S221J R 1608 (B,94,52) RS1/16SS104J R 1927 (A,15,30) RS1/16SS0R0J R 1613 (B,96,64) RS1/16SS0R0J R 1931 (B,25,26) RS1/16SS0R0J R 1621 (B,119,57) RS1/16SS0R0J R 1933 (B,25,27) RS1/16SS0R0J...
Page 64
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. R 2083 (B,92,44) RS1/16SS221J R 2084 (A,97,35) RS1/16SS221J C 1509 (A,85,63) CKSSYB104K10 R 2086 (A,98,33) RS1/16SS0R0J C 1510 (A,90,63) CKSSYB104K10 R 2087 (A,83,51) RS1/16S0R0J C 1511 (A,96,63) CKSSYB104K10 C 1512 (A,102,68) CKSSYB104K10...
Page 65
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No. MISCELLANEOUS C 1702 (A,105,69) CKSRYB104K25 C 1703 (A,90,96) CKSSYB104K10 VR11 (A,8,10) Semi-fixed 1 kΩ(B) CCP1442 C 1704 (A,91,96) CKSSYB103K16 VR12 (A,9,23) Semi-fixed 1 kΩ(B) CCP1442 C 1706 (A,92,96) CKSSYB104K10 R 11 (A,8,15)
6. ADJUSTMENT 6.1 DVD ADJUSTMENT TEST MODE [4] + [6] + Reset DVD source ON MG4 test mode FE test EDC1 test EDC2 test Mechanism select select select select Mechanism FE test mode EDC1 test mode EDC2 test mode test mode Note)When you turn off Acc in a static test mode, please be sure to check that the mechanism has stopped.
Page 67
- - Front-End test mode flow chart Note 1: At this stage select the media type. Various settings are carried out Note 2: While measurements are being taken, only the operation, for which Note 3: Reproduction (play) speed is selectable from DVD : x1.3 1.6CAV,CD : x 4CLV Fixation Note 4: Gain change: Normal gain ->...
Page 69
[Key] Operation Mech Test In Display CAM MOTOR LOAD MOTOR ELV MOTOR DISC CLAMP SELECTION Mech Test In Manual test Select the motor you desire to move by using one of the following four keys: After selecting the motor, use the SEEK UP or SEEK DOWN key tomove the selected motor. While the key is being pressed, the motor will keep moving.
6.2 SYSTEM MICROCOMPUTER TEST PROGRAM - Connection Diagram TUNER CONTROL UNIT (SIDE A) TUNER CONTROL UNIT (SIDE B) TESTIN PCL2 Measurement condition Measurement point Adjustment point Adjustment Method Temperature : 10 ˚C to 30 ˚C PCL2 TC601 Frequency Counter : 312.5 kHz ±...
7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 DISASSEMBLY Case Removing the Case (Fig.1) Remove the screw and then remove the Case. Removing the Grille Assy (Fig.1) Remove the two screws and then remove the Grille Assy. Fig.1 Grille Assy Removing the Holder (Fig.2) Remove the four screws and then remove the Holder.
Page 72
Removing the Tuner Control Unit (Fig.4) Remove the two screws. Straighten the tabs at three locations indicated. Remove the two screws. Disconnect the connector and then remove the Tuner Control Unit. Tuner Control Unit Fig.4 - Removing the Chassis (Fig.5) Remove the three screws and then remove the Chassis.
Page 76
PEG231A A0, A1 : Device address SCL : Serial clock input SDA : Serial data input/output WP : Write protect VCC : Power supply VSS : Ground NC : No connection TAS3108 AVSS AVDD vreg_en VR_PLL XTLI PLL2 XTLO PLL1 MCLKI PLL0 MICROCLK_DIV...
Page 77
PCM1606EG DATA1 SCKI System Clock Serial Input Function Control Manager DATA2 System Clock DATA3 LRCK 4x / 8x Zero Oversampling Digital Filter Detect FMT1 DEMP1 with Function controller FMT0 DEMP0 Enhanced Multilevel ∑∆ Modulator ZEROA AGND Output Amp Output Amp Output Amp Output Amp Output Amp...
Page 78
- Pin Functions(MN35103UB) Pin No. Pin Name Function and Operation VDD33 IO power supply I / O SDRAM data I / O SDRAM data VDD33 IO power supply 8-10 I / O SDRAM data 12,13 I / O SDRAM data VDD33 IO power supply VDD15...
Page 79
Pin No. Pin Name Function and Operation EXTRG1 I / O I/O trigger for debug Output trace clock for debug TRCCLK I / O 86-89 TRCDATA I / O I/O trace data for debug TRCST I / O Output trace status for debug VDD33 Power supply OSCI...
Page 80
Pin No. Pin Name Function and Operation AVDDG Analog power suplly Inside DAC bias current IREF2 AVSSG Analog GND COMP2 Inside DAC BECLK Backend clock input VDD33 IO power supply EXTCK Exterior audio clock PHCOMPO Composite audio clock LRCK LR chanel clock output SRCK Bit clock output ADOUT3...
Page 81
Pin No. Pin Name Function and Operation NCAS SDRAM column address strobe DQM0 SDRAM data mask VDD15 Power supply SDRAM data mask I / O SDRAM data I / O SDRAM data VDD33 IO power supply 251-253 I / O SDRAM data 255,256 I / O...
Page 82
LC75700TS KEY SCAN KEY BUFFER GENERAL PORT CLOCK GENERATOR CONTROL REGISTER INTERFACE SHIFT REGISTER ADM483E S-93C86BD4I-J8 CS : Chip select input SK : Serial clock input DI : Serial data input DO : Serial data output GND : Ground TEST TEST : Test NC : No connection VCC : Power supply...
Page 83
- Pin Functions (PEG133C) Pin No. Pin Name Format Function and Operation LET communication data output LETDO pllce@ Digital tuner : Chip enable output(EEPROM) DA output : Key back light brightness control output TXTPW Digital tuner : Chip enable output PLLPCE Digital tuner : Communication data output Digital tuner : Communication data input...
Page 84
Function and Operation Pin No. Pin Name Format Interruption to the reduced voltage IRQPWR Emphasis control ON/OFF sense input EMPHA_SEN DDcon(MG4 mechanism power supply) frequency switching output Internal 1.5vDDcon frequency switching DDCONF2 Not used DDCONF1 Multichannel mute B input bmute Clock output control mckena Not used...
Page 85
Function and Operation Pin No. Pin Name Format DPL II ON/OFF sense input "L" : OFF "H" : ON DPLSENS LCD back light input : short circuit/earth fault(breaking) sense BLVDSENS BLPW LCD back light power control output linh LCD INH output(switching LCD ON/OFF) KEY device communication chip enable output/LCD chip enable output KEY device communication data input/LCD data input KEY device communication clock output/LCD clock output...
Page 87
- Pin Functions(PE5555A) Pin No. Pin Name Format Function and Operation AVREF0 A/D converter reference voltage AVSS A power supply GND CRG drive output(controlled by claw) (Cannot used exept D/A) AVREF1 Not used CAMVOL Switching CAM motor driver output voltage E/LVOL1 Switching 1 ELV/LOAD motor driver output VPP/IC...
Page 88
Pin No. Pin Name Format Function and Operation ROMCS E2PROM chip selection output ROMCK E2PROM clock output /EPCS E2PROM input(L)/no input & (E2PROM chip selection (output)) /TESTIN Chip check test program starting up input /DBBUGIN Detection on-board debugger Not used LOADSWL LOAD operation sense L (DISC shape detecting, LOAD completed) LOADSWR...
Page 89
- FM/AM Tuner Unit 18 19 20 21 AM ANT 3.3V EEPROM COMP FM ANT TANK TANK MIX/IF/PLL DET/NC/MPC/MPX/DIV/RDS ANT1 X-tal No. Symbol I/O Explain 1 AMANT AM antenna input AM antenna input high impedance AMANT pin is connected with an all antenna by way of 33µH.
Page 94
- Jigs List Name Jig No. Remarks Assembly jig GGF1538 Assembly jig for MG4 (3pcs) 40-Pin flexible extension Flexible extension GGD1170 System Connection Cord GGD1496 - Grease List Name Jig No. Remarks PG641 GEM1024 Mechanism Module Unit(SERVICE) Before shipping out the product, be sure to clean the following portions by using the prescribed cleaning tools: Portions to be cleaned Cleaning tools DVD pickup lenses...