Miele H6260BP Quick Start Manual

fold here
Moisture Plus Cleaning and care
Oven mode: Moisture Plus Cleaning the oven
ĺ Confirm with OK.
Use only fresh tap water when cooking
Please refer to the Operating and in-
with the Moisture Plus function.
stallation instructions for more de-
The water intake process will begin.
ĺ Fold up the intake pipe and close the tailed information on cleaning and
Use the recipes as a guide.
care.
ĺ Fill a suitable container with the amount
door.
All surfaces of this appliance are sus-
of water required:
ceptible to scratching.
You briefly will hear the pump running.
– Automatic burst of steam
Remove any soiling immediately to pre-
 approx. 100 ml Danger of injury!
vent a permanent discolouration or alter-
Steam can cause scalding. Do not open
ation of the surface.
– Manual burst of steam the door during a burst of steam.

If you have selected , the burst of Surfaces of the oven cavity and differ-
approx. 100 ml

ent accessories treated with PerfectClean
approx. 200 ml
 steam is injected automatically after the
enamel are characterised by their excep-
approx. 300 ml
heating-up phase.
ĺ Select the Moisture Plus  function. ĺ Continue cooking until the end of the tional non-stick properties and ease of
cleaning.
 will appear with the triangle  flash- cooking duration.
If you have selected ,  or  bursts of To clean them by hand, you can
ing under the  symbol.
– remove the door
ĺ Use the rotary selector   to call up
steam, the number of bursts of steam
the other burst of steam options , ,  that can be injected appears in the dis- – dismantle the door
(the function  enables descaling). play after the heating-up phase.
– remove the FlexiClip telescopic runners
ĺ Touch  to inject the burst of steam.
(if present)
The recommended temperature will ap- pear in the display with the triangle  – remove the shelf runners
The sensor light goes out and the temper-
– lower the top heat/grill element
ature and the  symbol appear in the dis-
flashing under the  symbol.
ĺ Use the rotary selector   to change play.
Danger of burning!
ĺ Proceed as described to inject further
Make sure the oven heating elements
the temperature if necessary.
bursts of steam.
ĺ Confirm with OK. are switched off. Make sure the oven
has cooled down.
After the last burst of steam,  will go out
and the temperature will be displayed.
The prompt to draw in water appears. The
triangle  will flash under the  symbol.
ĺ Continue cooking until the end of the The fibreglass seal around the front of
the oven should be handled carefully.
ĺ Open the door and pull the intake pipe
cooking duration.
Do not rub and scour it.
forwards.
If possible, you should avoid cleaning it.
At the end of the cooking process:
ĺ Turn the function selector to .
ĺ Clean the oven front, the interior and the
ĺ Take the food out of the oven.
door with a clean sponge and a solution
ĺ Switch the oven off.
of warm water and washing-up liquid, or
with a clean, damp microfibre cloth.
Useful tip: When   appears in the dis-
ĺ Wipe dry using a soft cloth.
play you can use Moisture Plus ten more ĺ Leave all parts to dry.
times before the steam injection system
must be descaled.
The accessories are not dishwasher-safe.
ĺ Immerse the end of the water intake pipe
in the container with tap water.
fold here
fold here
Tips
Pyrolytic cleaning Energy saving tips
ĺ Coarse soiling should be removed before ĺ Remove any accessories that you are ĺ Monitoring the cooking time: Whenever
running the Pyrolytic cleaning programme. not using from the oven before starting possible set a cooking duration, or use
ĺ Remove accessories from the oven that
the cooking process. a roast probe.
ĺ Pre-heat the oven only if instructed to ĺ Use dark coloured baking tins and con-
are not designed for Pyrolytic cleaning.
ĺ Select Pyrolytic cleaning .
do so in the recipe or the cooking chart. tainers with a matt finish made from
ĺ Select the level of Pyrolytic cleaning re-
ĺ Try not to open the door during a cook-
non-reflective materials. Do not cover
quired:  ,   or  .
the oven floor or the rack with heat-re-
ing process. This will prevent heat from
ĺ Confirm with OK.
flecting aluminium foil.
escaping unnecessarily.
ĺ Energy-saving settings:
ĺ In general, if a range of temperatures is
The Pyrolytic cleaning programme will start. Select Status   for  .
 appears in the display and flashes until the given in a recipe or chart, it is best to
Select Status   for  .
select the lower temperature and check
door is locked. When  has gone out and 
flashes, the Pyrolytic cleaning programme is the food after the shortest duration.
Tips on baking, roasting and
ĺ Fan Plus : For baking and roasting
finished and the door has been released.
ĺ Turn the function selector to .
grilling
on different levels at the same time. A
lower temperature can be selected than
Baking
Danger of burning! Wait until the oven has
with Conventional Heat .
Bake on different levels at the same time
cooled down before removing residual ĺ Fan Grill : Lower temperatures can
using the Fan Plus  function:
soiling left in the oven compartment from
Pyrolytic cleaning. be used than when using the Grill 
– 1 tray: Shelf level 2
function.
ĺ Clean the oven interior and the inside of
ĺ Gentle Bake : Energy-efficient bak- – 2 trays: Shelf levels 1+3/2+4
the door with a clean, damp cloth.
– 3 trays: Shelf levels 1+3+5 (not suita-
ing with optimal use of heat (see "Over-
ble for moist cakes and tarts)
Evaporating residual moisture
view of functions").
ĺ Reduce energy consumption by utilising Roasting
If a programme using the addition of
Browning: Browning only occurs towards
moisture is manually interrupted before residual heat:
the end of the roasting time. Remove the lid
all the bursts of steam have been inject-
Cooking programmes using tempera-
about halfway through the roasting time if a
ed or if there is a power cut, the water for tures above 140 °C which take longer than
these unused bursts of steam will remain more intensive browning result is desired.
30 minutes:
in the steam injection system. As soon as Turn down to the lowest possible temper-
Standing time: At the end of the pro-
ature about 5 minutes before the end of
you select the Moisture Plus function ,
gramme, take the roast out of the oven,
cooking. The cooling fan remains switched
a time will appear, depending on the
wrap in aluminium foil and leave to stand
on. Do not switch the oven off completely.
amount of residual water present, and the
triangle  will flash under the  symbol.
for about 10 minutes. This helps retain
Whenever possible bake several dishes
juices when the meat is carved.
ĺ Confirm with OK. at the same time or immediately one after
the other.
Roasting poultry: For a crisp skin, baste
A Pyrolytic cleaning programme is best
The residual moisture evaporation process the poultry 10 minutes before the end of
will start. Once the time has elapsed, 
started immediately after a cooking pro-
the cooking time with slightly salted water.
gramme.
ĺ Energy saving mode: The oven will
will appear in the display.
ĺ Turn the function selector to . Grilling
switch itself off automatically to save
If the surface of a thicker cut of meat is
energy if a programme is not being run
While the residual water is evaporating, browned but the centre is still raw, move
and no controls are being operated.
the moisture will condense on the door the food to a lower level or reduce the tem-
perature and continue cooking. This will
and in the oven interior. It needs to be
stop the surface from becoming too dark.
wiped off after the oven has cooled down.
fold here
fold here fold here
Settings Problem solving guide
Settings overview
Most minor problems which may occur during daily operation, you can remedy yourself. Contact Miele if you cannot identify the cause of a problem or resolve it yourself.
Settings Status
    *
Problem
Time of day display on
 
off The display is dark.
   
Signal tones volume off
  to   on (  *)
    *
A function has been selected and
Keypad tone on
  the time of day and the  symbol
off
are still showing in the display.
   *
Clock format 24-hour format
 The oven does not heat up.
12-hour format  appears with  flashing un-
  ° *
Temperature unit Degrees Celsius
° der the  symbol.
Degrees Fahrenheit
    to   A function has been selected but
Display brightness minimum brightness to maximum brightness (
 *) the oven is not working.
 appears unexpectedly in the
    *
Lighting on for 15 seconds
  display and  is flashing at the
on same time. The buzzer might be
    *
sounding.
Demo mode deactivated   appears in the display.
 
activated
  or   appears in the display.
* factory setting  

Changing settings
The rack and other accessories
make a noise when being pushed
Your appliance is supplied with a number
into or pulled out of the oven.
A setting  is changed by altering its sta- of factory default settings.   °C
A noise can be heard after a cook-
tus . 
° :min
ing process.
        
ĺ Turn the function selector to .
No water is being taken in with the
Moisture Plus  function.
ĺ Select .
The setting is selected and the current   and  appear in the display.
status  appears, e. g. .
ĺ If necessary, use the rotary selector  
to move the triangle  until it appears   
To change the status:
The oven has switched itself off.
ĺ Use the rotary selector   to select
under .
There is soiling in the oven after
the status you want. the Pyrolytic cleaning programme.
ĺ Confirm with OK.
 
°C

°:min
Cakes and biscuits are not suffi-
The selected status is saved and the set-
       
 ciently baked after following the
ting appears again.
ĺ To change further settings, proceed in times given in the baking chart.
ĺ Confirm with OK.
A setting will appear, e.g.  . the same way.
Browning is uneven.
ĺ Select  if you do not want to change
ĺ If you wish to change another setting,
a setting and wish to switch to another.
ĺ If you do not want to change any further
use the rotary selector   to select the
appropriate number.
ĺ Confirm with OK. settings, select . The oven lighting does not switch on.
fold here fold here
fold here
Cause Remedy
– The time of day display is deactivated. – Check the settings for the time of day and change them if necessary.
– There is no power to the oven. – Check if the circuit breaker has tripped.
If it has, contact a qualified electrician or Miele.
The system lock  is switched on. Switch off the system lock (see "System lock").
Demo mode is activated.  appears in the display.
Deactivate Demo mode (see "Operating and installation instructions").
The power supply was interrupted for longer than Reset the time of day (see "Using for the first time").
200 hours.
There has been a power cut. This has caused the
Turn the function selector to  and switch the oven off.
current cooking process to stop. Restart the programme.
The oven has been operating for an unusually long Turn the function selector to  and switch the oven off.
time and this has activated the safety switch-off The oven is ready for use again immediately.
function.
A fault has occurred that you cannot resolve. Call Miele.
The Pyrolytic cleaning programme door lock is not Turn the function selector to  and select the Pyrolytic cleaning programme again. If the
locking ( ) or not opening ( ).
problem occurs again, contact Miele.
The pyrolytic resistant surface of the shelf runners To reduce the friction, add a few drops of heat resistant cooking oil to some paper tow-
creates friction when accessories are being pushed elling and use this to lubricate the shelf runners. Repeat this after each Pyrolytic clean-
into or pulled out of the oven. ing programme.
The cooling fan is switched on. It switches off automatically after a certain period.
– Demo mode is activated. – Deactivate Demo mode (see "Operating and installation instructions").
– The pump for the steam injection system is faulty. – Call Miele.
Moisture Plus  cannot be used. Carry out the descaling process (see "Operating and installation instructions"). All other
oven functions can still be used.
Energy save mode Switch the oven back on.
The Pyrolytic cleaning programme burns off soiling in – Remove the ash using a damp microfibre cloth or with a clean sponge and a solution
the oven and leaves it as ash. of hot water and washing-up liquid.
– If there is still coarse soiling left in the oven after the Pyrolytic cleaning programme,
start the programme again, selecting a longer duration.
– The ingredient quantities used are different from – Check whether there has been a change to the recipe. The addition of more liquid or
those given in the recipe. more eggs makes a moister mix which would take longer to cook.
– A different temperature from the one given in the
– Select the temperature required for the recipe.
recipe is used.
– The material or colour of the baking tin is not suita- – With Conventional Heat  light coloured, shiny tins are less suitable. Use matt, dark
ble for the oven function. coloured baking tins.
– The wrong temperature or shelf level was selected. – If the unevenness is pronounced, check whether the correct temperature and shelf
level have been selected.
There will always be a slight unevenness.
The halogen lamp is faulty and needs replacing. Replace the lamp with a new halogen bulb (see "Operating and installation instructions").
fold here
fold here
Quick Start Guide
H6260BP
These short instructions are not a substitute for the Operating and installation
instructions. It is essential to familiarise yourself with the oven before using it for the
first time. Please read the Operating and installation instructions carefully and pay
particular attention to the Warning and Safety Instructions.
en – AU, NZ M. No. 10 864 610
fold here