Setup of fire terminal (Touch) FT2080 ............4 Installation in 19" pedestal housing of the FC2080........6 Installation in housing (standard) ..............9 Installation in rear panel (FT2080) FHA2039 ..........10 Installation in desktop housing (FT2080) FHA2040 ........15 Technical data....................21 Building Technologies...
Setup of fire terminal (Touch) FT2080 1 Setup of fire terminal (Touch) FT2080 Rear panel fire terminal (Touch) FT2080 Support plate Front indicator (Touch) FTO2010 PMI & mainboard FCM2027 4x mounting hole operating unit Shield plate above carrier (CPU) Hinges for wall housing...
Page 5
Setup of fire terminal (Touch) FT2080 Arrangement of components Components on the fire terminal (Touch) FT2080, without cover cap Front indicator (Touch) FTO2010 Main network module (SAFEDLINK) on X13, optional License key, optional Slot 1 [SER_OPT1] for the first serial module at X14, optional...
Installation in 19" pedestal housing of the FC2080 2 Installation in 19" pedestal housing of the FC2080 The installation instructions described below apply to all operating units. Before an operating terminal is installed, the following components must first be installed on the operating unit. Network module (SAFEDLINK) FN2001-A1 with ES ≥...
Page 7
Installation in 19" pedestal housing of the FC2080 Operating unit Flange with threaded holes for securing the module Connector strip X13 for network module Network module (SAFEDLINK) FN2001-A1 with ES ≥ 12 2x fixing screw PMI & mainboard FCM2027 Adapter for power supply (including ribbon cable) Connector strip X3 peripheral data bus connection 1.
Page 8
Ribbon cable for FC2080 system supply to card cage (CPU) X30 FCnet connection to card cage (CPU) X11/X12 X3 connection to network module (SAFEDLINK) to PMI & mainboard FCM2027 Inside of door (section view) Fire terminal (Touch) FT2080 Adapter for flat cable of the supply FCnet FCnet Door...
Rear panel (standard) Fire terminal board FTI2001 Wiring FCnet/SAFEDLINK Network module (SAFEDLINK) FN2001 Fire terminal (Touch) FT2080 X3 Ribbon cable connection from the fire terminal (Touch) to the fire terminal board X1 Supply input for fire terminal board You will find detailed information on wiring the 'fire terminal board FTI2001' and the 'network module (SAFEDLINK) FN2001' in document Product Data 008837.
Installation in rear panel (FT2080) FHA2039 4 Installation in rear panel (FT2080) FHA2039 The rear panel (FT2080) can be used for installation in a desk or installation in a third-party housing. Installing the rear panel (FT2080) in a third-party housing guarantees the required EMC protection.
Page 11
Installation in rear panel (FT2080) FHA2039 Installing the fire terminal board FTI2001 Installing the fire terminal board in the rear panel (FT2080) Rear panel (FT2080) FHA2039 Fire terminal board FTI2001 4x fixing screw 4x mounting hole Threaded press-in sleeves in rear cover (FT2080) 1.
Page 12
Wiring the fire terminal (Touch) When installing in a desktop that is thicker than 33 mm, the cables must be routed through the rectangular openings of the rear panel (FT2080), and not through the round cable breakthroughs. Wiring view of the fire terminal (Touch) in the rear panel (FT2080)
Page 13
Fire terminal (Touch) FT2080 4x fixing screw 4x mounting hole in the fire terminal (Touch) Cable lead-through in the rear panel 4x threaded hole in the rear panel (FT2080) Lateral cable lead-throughs Rear panel (FT2080) FHA2039 Cut-out in the desktop...
Page 14
Installing the rear panel (FT2080) in a desktop Rear panel (FT2080) FHA2039 Mounted fire terminal (Touch) FT2080 4x fixing screw Mounting holes in the flanges of the rear panel (FT2080) Bores in the desktop Desktop Cutout for rear panel (FT2080) min. 430 x 268 mm 1.
Installation in desktop housing (FT2080) FHA2040 5 Installation in desktop housing (FT2080) FHA2040 View of desktop housing (FT2080) Top of desktop housing Tilting bracket for top of housing Base of desktop housing M4x10 pan head screw (scope of delivery) Clamping bracket for ground cable (scope of delivery)
Page 16
Installation in desktop housing (FT2080) FHA2040 1. Remove the top of housing (1) by pushing the two tilting brackets (2) on the left and right inwards until you can lift off the top of housing. 2. Connect the ground connection as shown with clamping bracket (5) and M4 pan head screw (4).
Page 17
Installation in desktop housing (FT2080) FHA2040 Installing fire terminal (Touch) FT2080 Mounting fire terminal in the cover of the desktop housing Tilting brackets on left and right for fixing the cover 2x fixing screw for tilting brackets and fire terminal...
Page 18
Installation in desktop housing (FT2080) FHA2040 Assembly of desktop housing (FT2080) Assembly of desktop housing Fire terminal (Touch) FT2080 Cover of desktop housing (FT2080) FHA2040 Tilting brackets on left and right for fixing the cover Guide cams on left and right for tilting brackets...
Page 19
Installation in desktop housing (FT2080) FHA2040 Securing cover for desktop housing Securing cap (scope of delivery) Opening for fixing screw Cover for desktop housing (Touch) Fixing screw with securing device 1. To close the housing, tilt the cover (3) onto the housing and secure the cover to the housing using both screws (4).
Page 20
Installation in desktop housing (FT2080) FHA2040 Fire terminal wiring Wiring view of the fire terminal in the desktop housing Fire terminal (Touch) FT2080 Network module (FCnet/SAFEDLINK) FN2001 Fire terminal board FTI2001 Prefabricated cable for supply connection to X7 fire terminal board...
Technical data: see doc. 008836 FT2080 - Control and Indicating Terminal for use in fire detection and fire alarm systems installed in buildings 2004/108/EC (EMC): EN 50130-4 / EN 61000-6-3 ; 2006/95/EC (LVD): EN 60950-1 ; 2011/65/EU (RoHS): EN 50581 ;...