Page 1
Over The Range Microwave Oven Installation Manual MWOTR 30100 SS MWOTR 30100 BL 01M-8851283200-2716-02...
Page 2
Please read this manual first! Dear Customer, Thank you for preferring a Beko product. We hope that you get the best results from your product which has been manufactured with high quality and state-of-the-art technology. Therefore, please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use.
CONTENTS 1 Important instructions 1.1 General safety ............4 1.1.1 Electrical safety............5 2 Your over the range convection microwave oven 2.1 Overview ..............6 2.2 Technical data ............6 3 Mounting space 4 External exhaust 4.1 Installing hood exhaust ........8 4.1.1 Outside top exhaust (example only) ...
Important instructions 1.1 General safety If not properly grounded, or if the outlet box does not meet elec- Read and save these in- trical requirements noted (under structions ELECTRICAL REQUIREMENTS), a qualified electrician should be em- Doing so will: ployed to correct any deficiencies. • make installation easier.
Important instructions The power cord of this appliance is equipped with a three-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the pos- sibility of electric shock hazard from this appliance. Do not, under any circumstances, cut, deform or remove any of the prongs from the power cord.
Mounting space Bottom Edge of Cabinet Needs to be 30 (76.2 cm) or More from the Cooking Surface “ (30.5 cm) min.] “ (42.5 cm) ⁄ “ “ (76.2 cm) (76.2 cm) min. Backsplash 66 (167.6 cm) or More from the Floor to the Top of the Microwave...
External exhaust 4.1 Installing hood exhaust Read these instructions only if you plan to vent your exhaust to the out- side. If you plan to recirculate the air back into the room, proceed to title 5 4.1.1 Outside top exhaust (example only) The following chart describes an example of one possible ductwork installation.
External exhaust 4.1.2 Outside back exhaust (example only) The following chart describes an example of one possible ductwork installation. Duct pieces Equivalent Number Equivalent Length used Length Wall Cap 40 Ft. (12.2 m) 40 Ft. (12.2 m) 3 Ft. Straight 3 Ft.
External exhaust 4.1.4 Maximum duct length For satisfactory air movement, the total duct 1⁄4 length of 3 ” x 10” (8.2 x 25.4 cm) rectangular or 6” (15.2 cm) diameter round duct should not ex- ceed 120 equivalent feet (36.5 m). 4.1.5 Elbows, transitions, wall and roof caps, etc., Present additional resistance to airflow and are...
External exhaust 45° Elbow 5 Ft. (1.5 m) Ft. or m Roof Cap 24 Ft. (7.3 m) Ft. or m Straight Duct 6“ (15.2 cm) 1 Ft. (0.3 m) Ft. or m Round or 1⁄4 ” x 10” (8.2 x 25.4 cm) rectangula Total Ductwork Ft.
External exhaust 4.3.2 Additional parts Part Quantity To p C abinet Template and Rear Wall Template Installation Instructions Separately Packed Grease Filters Exhaust adaptor Glass tray Turntable ring You will find the installation hardware contained in a packet with the unit. Check to make sure you have all these parts. NOTE: Some extra parts are included.
Installation 5.1 Placement of the 5. Remove the screws from the mounting plate. This plate will be used as the rear wall template mounting plate and for mounting. Reinstall the screws into the holes where they were removed. 5.1.1 Removing the microwave oven from the carton/ removing 5.1.2 Finding the wall studs the mounting plate...
Page 15
Installation The microwave must be level. Plate position—beneath framed recessed cabinet bottom Use a level to make sure the cabinet bottom is lev- If the cabinets have a front overhang only, with no back or side frame, install the mounting plate down the same distance as the front overhang NOTE: IT IS VERY...
Installation 3/8" TO EDGE 12" Trim the rear wall template along the dotted line. NOTE: IT IS VERY IMPORTANT TO READ AND FOLLOW THE DIRECTIONS IN THE INSTALLATION INSTRUCTIONS BEFORE PROCEEDING WITH THIS REAR WALL TEMPLATE. This Rear Wall Template serves to position the bottom 4"...
Installation 5.2 Installation types (choose This microwave is shipped assem- A, B or C) bled for Recirculating. Select the type of ventilation required for your this microwave oven is designed for adaptation to installation and proceed to that sec- the following three types of ventilation: tion.
Page 18
Installation A1. Attach Mounting Plate to Wall Be careful to avoid pinching fingers between the back of the mounting Attach the plate to the wall using toggle bolts. At plate and the wall. least one wood screw must be used to attach the plate to a wall stud.
Page 19
Installation A3. Adapting microwave blower for 4. Place the blower unit back into the opening. outside top exhaust AFTER: Fan Blade 1. Place the microwave in its upright position, with Openings Facing the top of the unit facing up. Remove the screw that holds the blower plate to the microwave.
Page 20
Installation A4. Check for proper damper opera- If filler blocks are not used, case tion damage may occur from overtight- ening screws. Blower Plate Exhaust Adaptor 1. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of Damper mounting plate.
Page 21
Installation 4. Attach the microwave oven to the top cabinet. 7. Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall Cabinet Front and the top cabinet.) Cabinet Bottom Shelf Filler Block Equivalent...
Page 22
Installation A7. Connecting ductwork 1. Extend the house duct down to connect to the exhaust adaptor. 2. Seal exhaust duct joints using furnance duct tape for high temperature applications. House Duct 22 / 32 EN Over The Range Convection Microwave Oven / Installation Manual...
Installation 5.2.2 Outside back exhaust (horizontal duct type B) 3/8" TO EDGE along the dotted line. Trim the rear wall template 12" NOTE: IT IS VERY IMPORTANT THE DIRECTIONS READ AND FOLLOW INSTRUCTION S IN THE INSTALLATION WITH THIS BEFORE PROCEEDING REAR WALL TEMPLATE.
Page 24
Installation B2. Remove blower plate 3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall Remove and save the screw that holds the blower to mount the plate. plate to the microwave. Lift off the blower plate. Before tightening toggle bolts and wood screw, make sure the tabs on the mounting plate touch the bot-...
Page 25
Installation B5. Adapting microwave blower for 4. Rotate blower unit counterclockwise 180°. outside back exhaust 1. Remove and save screw that holds blower Before Rotation After Rotation motor to microwave. Blower Motor Back of Microwave Back of Back of Microwave Microwave Blower Motor 5.
Page 26
Installation 8. Place the blower unit back into the opening. 11. Attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven. Push in AFTER: Fan Blade Openings Facing Back securely until it is in the lower locking tabs.
Page 27
Installation 4. Attach the microwave oven to the top cabinet. If filler blocks are not used, case damage may occur from overtight- Cabinet Front ening screws. Cabinet Bottom Shelf 1. Lift microwave, tilt it forward, and hook slots Filler Block at back bottom edge onto four lower tabs of mounting plate.
Installation 7. Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) 8. Install grease filters. See the Owner’s Manual packed with the microwave. 5.2.3 Recirculating (non-vented ductless type C) 3/8"...
Page 29
Installation Make sure the motor wiring has Before tightening toggle bolts and been properly routed and secured, wood screw, make sure the tabs on and that the wires are not pinched. the mounting plate touch the bot- tom of the cabinet when pushed C1.
Page 30
Installation C3. Check blower plate 1. Lift microwave, tilt it forward, and hook slots at back bottom edge onto four lower tabs of mounting plate. Blower Plate When mounting the microwave oven, thread power cord through hole in bottom of top cabinet. Keep it tight throughout Steps 1–3.
Page 31
Installation 5. Insert 2 self-aligning screws through outer top 1. Remove screws on top of grille using a #1 cabinet holes. Turn two full turns on each screw. Phillips screwdriver. 2. Open the door. 3. Remove the grille. Pull the grille straight off. Charcoal Filter 4.
How to use the product Before you use your over the range product; 1. Make sure the product has been installed according to instructions. 2. Remove all packing material from the product. 3. Install turntable ring and glass tray in cavity 4.