LG V-net ACS PWFMDB000 Installation & User Manual
  1. Manuals
  2. Brands
  3. LG Manuals
  4. Network Hardware
  5. V-net ACS PWFMDB000
  6. Installation & user manual
LG V-net ACS PWFMDB000 Installation & User Manual

LG V-net ACS PWFMDB000 Installation & User Manual

Type: internet bridge
Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTALLATION/USER MANUAL
• Make sure to read the cautions for safety before installation and use, and use
it correctly.
• It is intended to keep protect the safety of the installer and user and to
prevent the property damage, etc.
• After reading the user manual, please keep it at a place where user can
access any time.
TYPE : Internet Bridge
MODEL : PWFMDB000
P/NO : MFL67940704
www.lg.com

Advertisement

Table of Contents
loading

Related Manuals for LG V-net ACS PWFMDB000

Summary of Contents for LG V-net ACS PWFMDB000

  • Page 1 • It is intended to keep protect the safety of the installer and user and to prevent the property damage, etc. • After reading the user manual, please keep it at a place where user can access any time. TYPE : Internet Bridge MODEL : PWFMDB000 www.lg.com P/NO : MFL67940704...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS TABLE OF CONTENTS ACCS access environment setting CAUTIONS BEFORE THE Setting of the indoor units and ventila- INSTALLATION tion devices connected to the internet bridge ACCESSORY COMPO- CHECKLIST BEFORE NENT PARTS INSTALLATION INQUIRIES NAMES OF EACH PART OF THE INTERNET BRIDGE INSTALLING THE INTER-...
  • Page 3 CAUTIONS BEFORE THE INSTALLATION CAUTIONS BEFORE THE INSTALLATION • Installation work requires specialized technology, so it must be installed by service center or installa- tion specialty store acknowledged by the company. • If the installation work is done without installation qualification, the installer is responsible for all the problems related to the installation, and in such case, the company will not provide free service.
  • Page 4 CAUTIONS BEFORE THE INSTALLATION WARNING During the installation • When you install internet module inside the product, make sure to cut off the outdoor unit power. - It may cause electric shock. • Do not touch with hand while power is supplied. - It may cause fire, electric shock, explosion, injury, or failure.
  • Page 5 CAUTIONS BEFORE THE INSTALLATION WARNING • Firmly install on a place that can endure the weight of the internet bridge. - If the installation place is not strong enough, the internet bridge may fall and break. • Do not use the product in the following environments. - If the product is used in a place with oil, steam, or sulfuric acid gas, it may cause performance degradation or product damage.

  • Page 6: Accessory Component Parts

    ACCESSORY COMPONENT PARTS ACCESSORY COMPONENT PARTS Internet Bridge Components Open the packaging box of the internet bridge, and check if all the corresponding components are enclosed. Internet Bridge Internet Bridge Internet bridge manual Installation screw 3EA...

  • Page 7: Names Of Each Part Of The Internet Bridge

    NAMES OF EACH PART OF THE INTERNET BRIDGE NAMES OF EACH PART OF THE INTERNET BRIDGE Names of each part of the internet bridge It is the figure where PCB is installed inside the case, and the names of each part are as follows. ⑤...

  • Page 8: Installing The Internet Bridge

    INSTALLING THE INTERNET BRIDGE INSTALLING THE INTERNET BRIDGE Check list before installing the internet bridge • When you configure the internet bridge network, you can connect up to 16 outdoor units. Internet bridge composes the network with RS-485, and up to 16 outdoor unit PI485s can be connected.

  • Page 9: Selecting The Installation Place

    INSTALLING THE INTERNET BRIDGE Selecting the installation place • When it is installed with wireless communication Internet bridge shall be installed within 10m from AP. Communication is possible up to obstacles made of concrete wall (thickness 10cm or less) or wooden door (or window).

  • Page 10: Indoor Unit Address Setting

    INSTALLING THE INTERNET BRIDGE Indoor unit address setting The addresses of the indoor units connected to one internet bridge shall be assigned without overlapping. You can set the indoor unit address as hexadecimal 00 ~ FF. Note : Indoor unit address setting completed site - The site that already completed the indoor unit address does not require address setting again.

  • Page 11: Connecting Pi485 Cable

    INSTALLING THE INTERNET BRIDGE Connecting PI485 cable (for MultiV SuperIII model or lower) When you install PI485, you need to set DIP switch. (For DIP switch setting, refer to each PI485 manual.) After installing PI485, connect RS-485 cable. To connect PI485 and the internet bridge, two RS-485 cables shall be connected to PI485’s BUS_A and BUS_B.

  • Page 12: Connecting Pi485 Cable

    INSTALLING THE INTERNET BRIDGE Connecting PI485 cable (for MultiV Super IV) Connect the central controller communication line (RS485 cable) to the central control connec- tor (CEN_A, CEN_B) of the external board. * It shall be connected according to the polarity between the wires. External board Outdoor unit connector SODU...

  • Page 13: Fixing The Internet Bridge On The Wall

    INSTALLING THE INTERNET BRIDGE Fixing the internet bridge on the wall Internet bridge can be installed on a wall. Remove the screws on the right side to Fix it on the wall using the enclosed screws open the case of the Internet bridge. on the locations marked in the following fig- ure.

  • Page 14: Connecting Power And Wired Lan To

    INSTALLING THE INTERNET BRIDGE Connecting power and wired LAN to the internet bridge If wired LAN is used, connect LAN cable to A part in advance, and when wireless LAN is used, take a memo of the information (SSID, password, etc.) of AP to connect in advance. Internet bridge can work with DC 12V power.

  • Page 15: Combining The Internet Bridge Cases

    INSTALLING THE INTERNET BRIDGE Combining the internet bridge cases Combine the cases after going through the internet bridge setting in the next page. When the network setting is completed, combine the cases. Connect the upper part and the lower part to each other. Fix the right side of the case with a screw.

  • Page 16: Internet Bridge Setting

    Note : Preparations before the internet bridge network setting - For this step, LG Whisen system air conditioner App needs to be installed in the smart phone. - LG Whisen system air conditioner App can be downloaded from Google Play Store, and refer to the App manual for details.
  • Page 17 INTERNET BRIDGE SETTING Connect the internet bridge and the smart phone with wireless communication. Turn on Wi-Fi in the system Select LGE-XX-XX-XX. setting of the smart phone. Password : digitalwifi Input password and select After running the system connection. air conditioner App, select network setting button.
  • Page 18 INTERNET BRIDGE SETTING Note : Setting the wired communication - To set wired communication for the internet bridge, refer to the wired communication setting section. Wireless communication setting Select AP to connect to the internet bridge with wireless communication. Input the password, and Select the network set- select log-in button.
  • Page 19 If the network setting is incorrectly input, there may be communication defect, or control through the internet bridge may be impossible. Therefore, be careful and input correctly. Note : The password The LG System Air Conditioner Configuration password, please refer to the LG air condition- ing system home page.
  • Page 20 Input the password, and Select network setting. select log-in button. Select LAN, and press Press wired OK button. connection/network direct input. Note : The password The LG System Air Conditioner Configuration password, please refer to the LG air condition- ing system home page.
  • Page 21 INTERNET BRIDGE SETTING Set the IP. 2-1 Set dynamic IP. Select DHCP and press OK button. 2-2 Set static IP. Input the network informa- Select Static. tion and select OK button.
  • Page 22 INTERNET BRIDGE SETTING CAUTION For static IP setting, if the network settings (IP address, Gateway address, Subnet mask) are incorrectly input, there may be communication defect or control through the internet bridge may be impossible. Therefore, be careful and input correctly. Note : Network address assignment Internet bridge can use both the dynamic IP type and static IP type, but static IP type is recommended, and if dynamic IP type is used, it may cause inconvenience of the user.
  • Page 23 INTERNET BRIDGE SETTING When it is successfully set, LED 1 lamp continues to be lighted. If LED 1 lamp is not turned on, run the internet bridge setting again. LED1...
  • Page 24 It configures ACCS access environment setting. In PC environment, use IP_Search program to set ACCS access environment. Note : IP_Search program For information about installing IP_Search program, please refer to the LG Electronics air con- ditioning system home page. Run Ip_search.exe...
  • Page 25 INTERNET BRIDGE SETTING When the search results are displayed, select the desired device. Select a device and click “Confirm Device” button, then you can see that LED 1 of the corre- sponding internet bridge blinking 3 times with 1 second interval.
  • Page 26 INTERNET BRIDGE SETTING When you completed the verification of the internet bridge, click OK button after the selection. When the web browser is launched and the screen is displayed as follows, click the corre- sponding screen.
  • Page 27 INTERNET BRIDGE SETTING When you click the corresponding screen, the following program is automatically installed. Note : Program installation If the JAVA program usually is not installed, you can install it manually by downloading from the website of JAVA (http://www.java.com). [Recommended: JAVA6] •...
  • Page 28 Select Check Box and click Run button. When the program is successfully installed, the following screen is displayed. Note : Password The corresponding program is a program for the installer. Please refer to the LG system air conditioning website password.
  • Page 29 INTERNET BRIDGE SETTING Setting of the indoor units and ventilation devices connected to the internet bridge To the (Korean / English) and select the language. Input password and click Login button.
  • Page 30 INTERNET BRIDGE SETTING When the program runs normally, the following screen is displayed. Click system setting menu.
  • Page 31 INTERNET BRIDGE SETTING Click the installation button. Select Auto search button at the top left corner.
  • Page 32 INTERNET BRIDGE SETTING If automatic search button is pressed, it starts the search for the indoor units and ventilation products that are connected to the internet bridge. Automatic search takes about 5~10 min.
  • Page 33 INTERNET BRIDGE SETTING When the search is completed, indoor units/outdoor units list for each group is displayed. Change outdoor unit information You can change the outdoor unit name, central control address, outdoor unit capacity, and the number of the con- nected indoor units.
  • Page 34 INTERNET BRIDGE SETTING Apply the edited contents and click Save button. When it is saved, the following screen is displayed.
  • Page 35 INTERNET BRIDGE SETTING Automatic creation of the control group If you press [Smart Group Setting] button, the control group is automatically created based on the outdoor unit and ventila- tion group information input in the installation status. Moving indoor unit You can select an indoor unit and move to another outdoor unit.
  • Page 36 INTERNET BRIDGE SETTING If you press Revert button, contents edited so far disappears, and the last saved information is displayed again. Click Save & Send button to save the information. You need to finish the group setting to save the information.
  • Page 37 INTERNET BRIDGE SETTING Click General Configuration tab to move to TMS interface information management screen. Locking indoor unit address When indoor unit address lock is set, central control address cannot be changed from the indoor unit remote controller. CAUTION • Beware that the central control address cannot be changed from the remote controller when the address lock is set.
  • Page 38 INTERNET BRIDGE SETTING Modify each category except the site code by referring to the next page’s TMS interface information. Note : TMS interface information TMS interface information to input are as follows Category Description ② Connection PORT number Input TMS system communication port number. (Select one from 21 or 23) ③...
  • Page 39 INTERNET BRIDGE SETTING Click the 'Select TimeZone' button Select the city closest to the location of the installation of the product. CAUTION If you do not set the TimeZone, you will not be able to set the TMS linked information.
  • Page 40 INTERNET BRIDGE SETTING Click Save button to save TMS interface information. Click Register site code button to request the site code.
  • Page 41 INTERNET BRIDGE SETTING When the popup window appears, press Confirm button. If you press Query button within about 1 min., you can see that the site code is changed.
  • Page 42 INTERNET BRIDGE SETTING Click Save button to save the changed information. Check the site code, and apply for registration in TMSII home page. (Refer to TMS User Manual) ※ Record the site code separately and directly hand over to the customer.
  • Page 43 CHECKLIST BEFORE INSTALLATION INQUIRIES CHECKLIST BEFORE INSTALLATION INQUIRIES Trouble Shooting Guide Major Function Possible causes Corrective action • Did you complete the group set- • Set the indoor unit and outdoor ting using ACCS? unit groups and run again. Internet bridge LED 2 does not blink.
  • Page 44 • Close Explorer window and run a • Are several programs running in new explorer to access again. the computer? LG ACCS GUI is not • In the process manager, end all operational. iexplore.exe processes and access the internet bridge again.
  • Page 45 In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com.
  • Page 46 CHECKLIST BEFORE INSTALLATION INQUIRIES NOTE FCC Compliance Information This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received. Including interference that may cause undesired operation.
  • Page 47 CHECKLIST BEFORE INSTALLATION INQUIRIES Class B device NOTE This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equip- ment if an unauthorized change or modification is made.

Table of Contents