Siemens SBGA-34 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Security Sensors
  5. SBGA-34
  6. Installation instructions manual
Siemens SBGA-34 Installation Instructions Manual

Siemens SBGA-34 Installation Instructions Manual

Audible base
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
INSTALLATION INSTRUCTIONS
Model SBGA-34
Audible Base
INTRODUCTION
The Model
SBGA-34 Audible Base from Siemens Industry, Inc., consists of a standard Series 11 base
combined with an audible device compatible with all H-series, 8700 series, Desigo and Cerberus series
addressable detectors. All field wiring terminates at two four-position terminal blocks located on the back
of the unit. The SBGA-34 is used with the polarity insensitive HFP-11, HFPT-11, HFPO-11, SFP-11*,
SFPT-11* and SFPO-11*, 8710, 8712, 8713, FDO421, FDT421, FDOT421, FDOOT441, FDOOTC441,
OP921, OH921, HI921, OOH941, OOHC941 detectors. The SBGA-34 operates as described below
(Refer to Figures 1, 2, 3, 4, 5, 6 and 7 for proper wiring connections).
*SFP-11, SFPT-11 and SFPO-11 detectors are approved for use in CANADA only.
JA-BI20 (3 WIRE)
P1
1
POWER INPUT
120 VAC, 50/60 Hz
CONNECTED TO GROUND
REFERENCE OF THE PANELS
IT'S CONNECTED TO (REFER
TO TABLE X FOR GROUND
CONNECTION)
LINE 2
FOR CONNECTION
NOTE 4
TO SLC LOOP
LINE 1
1. Polarity shown in active state at terminals 1 and 2 of SBGA-34. Proper
polarity must be maintained or audible base will not operate properly.
Each audible base must be tested to verify operation.
2. Use a Model MPI-2 mounting plate to mount a HTRI-R in a System 3
enclosure. HTRI-R relay should be programmed to activate on
appropriate alarm condition. For more detailed wiring information, refer
to the HTRI-R Installation Instructions, P/N 315-033300.
3. Tone selection (refer to page 7 for more i nformation).
4. HTRI-R and SBGA-34 are polarity insensitive. Line 1 and Line 2 can
be either line of the loop.
LINE 1
FROM DLC LOOP OF
NOTE 4
LINE 2
Figure 1
Installation/Wiring Diagram for SBGA-34 Powered by Auxiliary Power Supply with Battery Backup
Siemens Industry, Inc.
Building Technologies Division
Florham Park, NJ
P/N A6V10383428_a_en--
BI-35
P1
P2
PS-35
7
8
9
10
2
3
4
5
6
1
2
3
4
5
3.6K,
1/4W,
MODEL
EL-31
NOTE 2
8
5
7
6
4
3
2
HTRI-R
1
FIREFINDER-XLS
SYSTEM OR FS-DLC LOOP OF FS-250 SYSTEM
JA-BI24 (7 WIRE)
NOTE:
WHEN THE OPTIONAL MM-35 IS NOT USED,
A SUPERVISORY CONNECTION MODEL
JP-BE MUST BE INSTALLED AT P2 IN THE
LAST BC-35 OR BE-35 MODEL.
FOR P1 CONNECTION USE
6
JA-24 OR EQUIVALENT, AND
REWORK AS NECESSARY
JS-24 (1 WIRE) FROM PIN 3 OF LAST MODULE
P1
P2
2
1
(10 WIRE)
4
3
6
5
8
7
10
9
7
8
AA-30U
1
2
3
4
5
6
-
-
NOTE 3
NOTE 1
2
1
4
3
4
3
SBGA-34
SBGA-34
7
5
6
8
5
6
STYLE Z
(CLASS A)
BC-35
7
8
12-PIN
PLUG
24 VDC
BATTERY
JA-5
AE-30U
P1
P2
3.6K,
1/4W,
MODEL
EL-31
3
4
5
6
1
2
-
3.6K,
1/4W,
MODEL
EL-31
-
-
-
-
NOTE 3
NOTE 1
2
1
2
1
2
4
3
4
3
SBGA-34
SBGA-34
7
7
7
8
5
6
8
5
6
5
1a
DB-X3RS, OR DB-11
DB-11
6
1b
STYLE Y
(CLASS B)
1
8
LINE 2
TO NEXT
SBGA-34, DB3S,
LINE 1

Advertisement

Table of Contents
loading

Related Manuals for Siemens SBGA-34

Summary of Contents for Siemens SBGA-34

  • Page 1 All field wiring terminates at two four-position terminal blocks located on the back of the unit. The SBGA-34 is used with the polarity insensitive HFP-11, HFPT-11, HFPO-11, SFP-11*, SFPT-11* and SFPO-11*, 8710, 8712, 8713, FDO421, FDT421, FDOT421, FDOOT441, FDOOTC441, OP921, OH921, HI921, OOH941, OOHC941 detectors.
  • Page 2 ZONE 4 ZIC-4A 1. Polarity shown in active state at terminals 1 and 2 of SBGA-34 and 1-4 of ZIC-4A. Proper polarity must be maintained or audible base will not operate properly. Each audible base must be tested to verify operation.
  • Page 3 TB13 TB12 1. Polarity shown in active state at terminals 1 and 2 of SBGA-34 and 1+, 1-, 2+ and 2- of FS-250/FS-250C NAC cirucits. Proper polarity must be maintained or audible base will not operate properly. Each audible base must be tested to verify operation.
  • Page 4 NOTE 2 NOTE 2 1. Polarity shown in active state at terminals 1 and 2 of SBGA-34 and 1+, 1-, 2+ and 2- of FC-901 NAC circuits. Proper polarity must be maintained or audible base will not operate properly. Each audible base must be tested to verify operation.

  • Page 5: Application Note

    When used to follow the NAC tone pattern, the SBGA-34 must be set to steady tone and the panel it is connected to must be configured accordingly for the desired application. This allows the SBGA-34 to transition from one tone to another (example from temporal 4 to temporal 3) if the proper criteria is met and allows it to be synchronized with the NAC zone that it is connected.

  • Page 6: Detector Placement

    FC360 Installation Instructions, P/N A6V10336754. 6. T-tapping of the notification appliance circuit is not allowed. 7. When SBGA-34 Is powered from external power supply source, care must be taken to insure that proper ground fault detection is not compromised In typical application where the...

  • Page 7: Detector Wiring

    SBGA-34 Audible Base Terminal Blocks TONE SELECTION With audible base Model SBGA-34, the user can choose either temporal tone (Temporal 3 or Temporal 4) or steady tone (Refer to figure 8). For Temporal Tone: Terminal 3 and 4 are shorted (insert a jumper)  Default setting is Temporal 3 To Select Temporal 4: Open the unit by unscrewing the DB-11 connected to the base Move the J3 jumper to 2-3 position and refit the DB-11 to the base.

  • Page 8: Detector Mounting

    The detector base comes from the factory prewired. All signaling and initiating circuits are connected directly to the back of the SBGA-34 audible base using the four-position terminal blocks. NOTE: The Audible Base Model SBGA-34 attaches only to a 4-inch square electrical box with extension. Mounting the Base Route all wires out from the outlet box.

Table of Contents