Sharp XV-Z10000 Operation Manual
Sharp operation manual projector xv-z10000
Hide thumbs
Also See for XV-Z10000:
- Service manual (178 pages) ,
- Operation manual (94 pages) ,
- Operation manual (95 pages)
Table of Contents
Related Manuals for Sharp XV-Z10000
Summary of Contents for Sharp XV-Z10000
-
Page 1: Operation Manual
PROJECTOR PROJECTEUR PROYECTOR PROJETOR XV - Z10000 OPERATION MANUAL MODE D’EMPLOI MANUAL DE OPERACION MANUAL DE OPERAÇÃO ENGLISH ... FRANÇAIS ... ESPAÑOL ... PORTUGUÊS ... -1 – -1 – -1 – -1 –... -
Page 2: Introduction
2. CONSUMER PRODUCT SAFETY ACT To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE. -
Page 3: Declaration Of Conformity
WARNING: The cooling fan in this projector continues to run for about 90 seconds after the projector is turned off. During normal operation, when turning the power off always use the power (OFF) button on the projector or on the remote control. -
Page 4: Outstanding Features
Outstanding Features 1. High Color Purity and Broad Dynamic Range Due to Advanced Optical Engine Newly developed 12° DMD™ chip provides significantly improved opti- cal efficiency and excellent contrast ratio. Newly developed DDR (Double Data Rate) chip eliminates Color Break- ing phenomena common with previous generation DLP™... -
Page 5: Table Of Contents
Controlling the Projector by a Computer ... 23 Controlling the Projecor Using an RS-232C Cable ... 23 Using as a Wired Remote Control ... 24 Connecting the Remote Control to the Projector ... 24 Using the Adjustment Feet ... 25 Adjusting the Lens ... 26 Using the Lens Shift ... - Page 6 Wired Remote Control Terminal Specifications ... 83 Specifications of wired remote control input ... 83 Function and transmisson codes ... 83 Sharp remote control signal format ... 83 Computer Compatibility Chart ... 84 Troubleshooting ... 85 For SHARP Assistance (U.S.A only) ... 86 Specifications ...
-
Page 7: Important Safeguards
IMPORTANT SAFEGUARDS CAUTION : Please read all of these instructions before you operate this product and save them for later use. Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. - Page 8 18. Damage Requiring Service Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product.
-
Page 9: Important Safeguards
Cautions concerning the setup of the projector I For minimal servicing and to maintain high image qual- ity, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the lens must be cleaned more often. -
Page 10: How To Access The Pdf Operation Manuals Of Sharpvision Manager
How to Access the PDF Operation Manuals of SharpVision Manager PDF operation manuals for the “SharpVision Manager” theater projector software provided are included in the CD-ROM in several languages. To utilize these manuals, you need Adobe Acrobat Reader installed on your PC (Windows or Macintosh). If you have not installed Acro- bat Reader yet, you can install it from the CD-ROM. -
Page 11: Part Names
Part Names Numbers in refer to the main pages in this operation manual where the topic is explained. Projector (Front and Top View) Adjustment buttons (", ', \, |) For selecting menu items. ENTER button For setting items selected or adjusted on the menu. -
Page 12: Projector (Rear View)
Using the Kensington Lock This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector. -
Page 13: Part Names
For switching the screen size (NORMAL, STRETCH, etc.) PICTURE SETTING button For selecting the picture memory setting. Backlight button For lighting each button, press this button. WIRED R/C JACK For controlling the projector by connecting the remote control to the projector. -
Page 14: Using The Remote Control
Battery fluid from leaked batteries is harmful to your skin, therefore be sure to first wipe them and then remove them using a cloth. The batteries included with this projector may exhaust over a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries when they have run out. -
Page 15: Accessories
Accessories Supplied accessories Remote control RRMCGA128WJSA Lens cap (attached) PCAPH01056CESA Optional accessories DVI to 15-pin D-sub adaptor RS-232C cable (32'10'' (10.0m)) 3 RCA to 15-pin D-sub cable (9'10'' (3.0m)) DVI cable (9'10'' (3.0m)) Some of the cables may not be available depending on the region. Please check with your nearest Note Authorized SharpVision Service Center or Dealer. -
Page 16: Connections And Setup
Connections and Setup... -
Page 17: Connecting The Projector To Other Devices
Before Connecting Note Before connecting, be sure to turn off both the projector and the devices to be connected. After making all connections, turn on the projector and then the other devices. When connecting a computer, be sure that it is the last device to be turned on after all the connections are made. -
Page 18: Connecting To Video Equipment
Connecting the Projector to Other Devices Connecting to Video Equipment Connecting to Video Equipment Using an S-video or a Composite Video Cable Using an S-video or a composite video cable, a VCR, laser disc player or other video equip- ment can be connected to INPUT 3 and INPUT 4 input terminals. -
Page 19: Connecting To Component Video Equipment Using A Component Cable (Input 1 Or 2)
INPUT 1 or 2 terminal, component video equip- ment such as DVD players and DTV* decoders. *DTV is the umbrella term used to describe the new digital television system in the United States. Connect the projector to the com- ponent video equipment using the component cable. Note When connecting the projector to the video equipment in this way, select “Com-... -
Page 20: Connecting To Component Video Equipment Using A 3 Rca To 15-Pin D-Sub Cable Using The Dvi To 15-Pin D-Sub Adaptor (Input 5)
*DTV is the umbrella term used to describe the new digital television system in the United States. Connect the projector to the video equipment using a 3 RCA to 15-pin D-Sub cable using the DVI to 15-pin D-Sub adaptor. -
Page 21: Connecting To Video Equipment With The Dvi Output Termianl Using The Dvi Cable
DVD players and DTV* decoders. *DTV is the umbrella term used to describe the new digital television system in the United States. Connect the projector to the video equipment using the DVI cable. Note Select the input signal type of the video equipment. -
Page 22: Connecting The Projector To A Computer
Note See page 84 “Computer Compatibility Chart” for a list of computer signals com- patible with the projector. Use with com- puter signals other than those listed may cause some of the functions not to work. When connecting the projector to a com- puter in this way, select “RGB”... -
Page 23: Connecting To A Computer Using A Dvi Cable (Sold Separately)
I This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible computer will communicate their setting requirements, allowing for quick and easy setup. I Before using the “Plug and Play” function, be sure to turn on the projector first and the connected computer last. -
Page 24: Controlling The Projector By A Computer
RS-232C cable (null modem, cross type, sold sepa- rately), the computer can be used to control the projector and check the status of the pro- jector. See page 80 for details. Connect the projector to the com- puter using an RS-232C cable. -
Page 25: Using As A Wired Remote Control
(rear projection, etc.), connect a ø3.5 mm minijack cable (commercially available or available as Sharp service part QCNW- 4870CEZZ) from the WIRED R/C JACK on the top of the remote control to the WIRED RE- MOTE control input terminal. -
Page 26: Using The Adjustment Feet
Feet The height of the projector can be adjusted using the adjustment feet when the surface the projector is placed on is uneven or when the screen is slanted. The projection of the image can be made higher by adjusting the projector when it is in a location lower than the screen. -
Page 27: Adjusting The Lens
Setup Adjusting the Lens The image is focused and adjusted to the desired size using the focus ring or zoom knob on the projector. Zooming is adjusted by mov- ing the zoom knob. The focus is adjusted by rotat- ing the focus ring. -
Page 28: Using The Lens Shift
The height of the projected image can be ad- justed within the shift range of the lens by rotating the lens shift dial on the top of the projector. Note Do not forcibly turn the lens shift dial be- yond the range of the upper limit and lower limit positions. -
Page 29: Setting Up The Screen
Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image. Note The projector lens should be centered in the middle of the screen. If the horizontal line passing through the lens center is not perpendicular to the screen, the image will be distorted, making viewing difficult. -
Page 30: Screen Size And Projection Distance
Setup Screen Size and Projection Distance When using a normal Screen size (4:3) screen (4:3) In case of setting the Diag. (x) 16:9 picture to the full 250" horizontal width of the 200" 4:3 screen. 150" 100" 84" 72" 60" The formula for screen size and projectino distance (Max.) = (0.05058x –... -
Page 31: Projecting A Reversed/Inverted Image
Ceiling-mount setup I It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. I Before mounting the projector, contact your nearest Authorized SharpVision Service Center or Dealer to obtain the recommended ceiling-mount bracket (sold separately). -
Page 32: Basic Operation
Basic Operation... -
Page 33: Image Projection
Press on the remote control on the projector. The power indicator illuminates blue. After the lamp replacement indicator il- luminates, the projector is ready to start operation. Note The lamp replacement indicator il- luminates, indicating the status of the lamp. - Page 34 Note When no signal is received, “NO SIGNAL” will be displayed. When a signal that the projector is not pre- set to receive is received, “NOT REG.” will be displayed. The INPUT mode is not displayed when “OSD display”...
-
Page 35: Selecting The On-Screen Display Language
Selecting the On-screen Display Language The on-screen display language of the projector can be set to English, German, Spanish, Dutch, French, Italian, Swedish, Portuguese, Chinese, Korean or Japa- nese. Press The menu will be displayed. - Page 36 Press ' or " to select the de- sired language, and then press Press The desired language will be set as the on-screen display.
-
Page 37: Keystone Correction And Vertical Size Adjustment
Keystone Correction and Vertical Size Adjustment Correcting Trapezoidal Distortion and Adjust- ing the Vertical Size of the Picture This function allows for Keystone (On-screen Trapezoidal Distortion) Correction and the adjustment of the vertical size of the picture. Note When the image is projected either from top or from bottom toward the screen at an angle, the image becomes distorted trapezoidally. - Page 38 When adjusting vertical size, pressing again displays the vertical size adjustment menu. Press "and ' to adjust the vertical size of the picture, and press See below for details about the verti- cal size adjustment. Vertical Size Adjustment UNDO button The screen aspect ratio may change when the lens shift function is used in combination with the Keystone Correction function.
-
Page 39: Menu Bar Items
Menu Bar Items This list shows the items that can be set in the projector. I INPUT 1 / 2 / 5 Mode Main menu Sub menu Picture Contrast –30 Page Bright –30 Color –30 Tint –30 Sharp –30 CLR Temp... - Page 40 I INPUT 3 / 4 Mode Main menu Sub menu Picture Contrast –30 Page 44 –30 Bright Color –30 –30 Tint Sharp –30 CLR Temp 5500 11500 Reset White Emphasis [ON/OFF] Gamma Position Standard Black Detail Brighten Custom 1 Custom 2...
-
Page 41: Using The Menu Screen
Using the Menu Screen This projector has two sets of menu screens that allow you to adjust the image and various projector settings. You can operate the menus from the projector or remote control using the following proce- dure. Menu screen for INPUT 1,... - Page 42 Press \ \ \ \ \ or | | | | | to select the menu you want to adjust. Note For details on the menus, see the tree charts on pages 38 and 39. " " or ' " " ' ' to select the item Press "...
-
Page 43: Menu Selections (Settings)
Using the Menu Screen Menu Selections (Settings) Press The menu screen is displayed. Note The “Picture” menu screen for the selected input mode is displayed. The on-screen displays shown on the lower right is displayed when IN- PUT 1, 2 or INPUT 5 RGB mode is selected. - Page 44 Press | | | | | . The cursor shifts to the sub menu. " " " " or ' ' ' to select the set- Press " ting of the item displayed in the sub menu. Press The item selected is set. Note Some adjustment items will display a confirmation message.
-
Page 45: Adjusting The Picture
Adjusting the Picture You can adjust the projector’s picture to your preferences with the following picture settings. Adjusting Image Prefer- ences Note First select “INPUT # Memory” when you want to save the “Picture” menu settings. See page 47 for details. -
Page 46: Emphasizing The Contrast
Emphasizing the Con- trast This function emphasizes the bright portions of images to obtain a higher contrast image. Select “White Emphasis” in the “Pic- ture” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note Emphasizes the bright portions of images. -
Page 47: Progressive Mode
* The film source is a digital video record- ing with the original encoded as is at 24 frames/second. The projector can con- vert this film source to progressive video at 60 frames/second with NTSC and... -
Page 48: Picture Setting Function
Picture Setting Func- tion This function stores all items set in “Picture”. Five settings can be stored separately in “Memory 1” to “Memory 5”. Each stored set- ting is reassigned to each input mode (INPUT 1 to INPUT 5). Even when the input mode or signal is changed, you can easily select opti- mal settings from the stored settings. -
Page 49: Adjusting The Gamma
Adjusting the Gamma Use this function to select the gamma position and adjust the gamma curve for finer image adjustment. Selecting the Gamma Position Select “Gamma Position” in the “Gamma” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. -
Page 50: Adjusting The Gamma
Adjusting the Gamma Adjust the gamma curve to suit your prefer- ences. Select the gamma item in the “Gamma” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note These gamma values can be adjusted only when the gamma position is set to “Custom 1”... -
Page 51: Color Management System (C. M. S.)
➝For operating the menu screen, see pages 40 to 43. Selected item Description Standard Sharp default setting Custom 1-3 “Lightness”, “Chroma” and “Hue” can be adjusted for each of the six colors. Note If “Standard” is selected for “Color Se- lected”, other items (e.g., Target) cannot... -
Page 52: Setting The Brightness Of The Target Color
Setting the Brightness of the Target Color Select “Lightness” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Setting the Chromatic Value of the Target Color Select “Chroma” in the “C.M.S.” menu on the menu screen. -
Page 53: Resetting User-Defined Color Settings
Color Management System (C.M.S.) Resetting User-Defined Color Settings Select “Reset (This Color)” or “Reset (All Colors)” in the “C.M.S.” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Selected item Description Reset “Lightness”, “Chroma” and “Hue” (This Color) of the color selected for “Target”... -
Page 54: Adjusting Computer Images
. See page 55 for details. Saving Adjustment Settings This projector allows you to store up to seven adjustment settings for use with various com- puters. Select “Save Setting” in the “Fine Sync” menu on the menu screen. -
Page 55: Selecting Adjustment Settings
Selecting Adjustment Settings Adjustment settings stored in the projector can be easily accessed. Select “Select Setting” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Note If a memory position has not been set, a resolution and frequency setting will not be displayed. -
Page 56: Checking The Input Signal
When setting to “ Normal” or “ High Speed”: Auto Sync adjustment will occur when the projector is turned on or when the inputs are switched, when connected to a com- puter. Manual adjustments should be per- formed: When the optimum image cannot be achieved with Auto Sync adjustment. -
Page 57: Auto Sync Display Function
Auto Sync Display Function Used to set the screen displayed during Auto Sync. Select “Auto Sync Disp” in the “Fine Sync” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. Selected item Description The image set as a back- ground image is projected. -
Page 58: Easy To Use Functions
Easy to Use Functions... -
Page 59: Selecting The Picture Display Mode
Selecting the Picture Display Mode This function allows you to modify or customize the picture display mode to enhance the input image. Depending on the input signal, you can choose “NORMAL”, “FULL”, “DOT BY DOT”, “BORDER”, “STRETCH” or “SMART STRETCH” image. Switching the Picture Display Using Different Input Signals... - Page 60 VIDEO 480I 480P 576I For 4:3 576P aspect ratio NTSC SECAM 480P For 16:9 720P aspect ratio 1080I “STRETCH” is fixed when 720P, or 1080 signals are entered. * The Digital Shift function can be used with these images. Input Signal SIDE BAR SMART STRETCH For 4:3 aspect ratio...
- Page 61 COMPUTER SVGA (800 For 4:3 XGA (1024 aspect ratio SXGA (1280 For without SXGA (1280 4:3 aspect ratio “NORMAL” is fixed when XGA (1024 768) signals are entered. Output screen image Input Signal NORMAL For 4:3 aspect ratio (640 480) SVGA For 4:3 aspect ratio (800...
-
Page 62: Switchable High Contrast/High Brightness Mode
This function controls the quantity of the projected light and the contrast of the image. It can be operated using the HIGH CONTRAST/HIGH BRIGHTNESS MODE button on the projector. Set “NORMAL” when the projector is used in a relatively bright room. -
Page 63: Digital Shift Function
Digital Shift Function For easier viewing, this function shifts the entire image projected on the screen up or down when projecting 16:9 images from DVD players and DTV* decoders. * DTV is the umbrella term used to describe the new digital television system in the United States. -
Page 64: Video Digital Noise Reduction (Dnr) System
Video Digital Noise Reduction (DNR) System Digital Noise Reduction (DNR) provides high quality images with minimal dot crawl and cross color noise. Reducing Image Noise Select “DNR” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. -
Page 65: Selecting The Signal Type
Selecting the Signal Type This function allows you to select the input signal type RGB or Component for INPUT 1 and 2, or Digital PC RGB, Digital PC Compo- nent, Digital Video RGB, Digital Video Com- ponent, Analog RGB or Analog Component for INPUT 5. -
Page 66: Setting The Video System
Setting the Video System The video input system mode is preset to “Auto”; however, a clear picture from the con- nected audio-visual equipment may not be received, depending on the video signal differ- ence. In that case, switch the video signal. Setting the Video System Select “Video System”... -
Page 67: Setting A Background Image
Setting a Background Image This function allows you to select the image displayed when no signal is being sent to the projector. Selecting a Background Image Select “Background” in the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. -
Page 68: Selecting The Economy Mode
Selecting the Economy Mode These functions allow you to reduce the power consumption of the projector. Setting the Power Save Select “Power Save” in “Economy Mode” under the “Options” menu on the menu screen. ➝For operating the menu screen, see pages 40 to 43. -
Page 69: Automatic Power Off Function
➝For operating the menu screen, see pages 40 to 43. Note Make sure that both the projector and computer are set for the same baud rate. Refer to the computer’s operation manual for instructions for setting the computer’s... -
Page 70: Reversing/Inverting Projected Images
Reversing/Inverting Projected Images This projector is equipped with a reverse/invert image function that allows you to reverse or invert the projected image for various applications. Setting the Projection Mode Select “PRJ Mode” in the “Options” menu on the menu screen. -
Page 71: Displaying The Adjustment Settings
Displaying the Adjustment Settings This function can be used to display all the adjusted settings as a list on the screen. Overview of All Menu Settings Select the “Status” menu on the menu screen and press ➝For operating the menu screen, see pages 40 to 43. -
Page 72: Appendix
Appendix... -
Page 73: Maintenance
I When the dirt is hard to remove, soak a cloth in a neutral detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. -
Page 74: Cleaning The Ventilative Holes
• The ventilative holes should be cleaned every 100 hours of use. Clean the ventilative holes more often when the projector is used in a dirty or smoky location. Cleaning the Ventilative Holes Turn off the power and discon- nect the power cord. -
Page 75: Maintenance Indicators
Maintenance Indicators I The warning lights on the projector indicate problems inside the projector. I If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will illuminate red, and the power will turn off. After the power has been turned off, follow the proce- dures given below. - Page 76 If the temperature warning indicator illuminates, and the power turns off, follow the above possible solutions and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 5 minutes.) If the power is turned off and then turned on again, as during a brief test, the lamp replacement indicator may be triggered, preventing the power from going on.
-
Page 77: Regarding The Lamp
Replacing the Lamp Caution Do not remove the lamp unit immediately after operation of the projector. The lamp will be hot and touching it can lead to burn or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit. -
Page 78: Removing And Installing The Lamp Unit
Wait until the cooling fan stops. Warning! Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn or injury. Disconnect the power cord. Unplug the power cord from the AC socket. -
Page 79: Resetting The Lamp Timer
Attach the lamp unit cover. Close the lamp unit cover in the direc- tion of the arrow (to the close mark) on the side of the projector. Then tighten the user service screw. Info If the lamp unit and lamp cover are not... -
Page 80: Connecting Pin Assignments
Connecting Pin Assignments DVI-I (INPUT 5 / DIGITAL INPUT) port : 29 pin connector 24 23 18 17 DVI Analog RGB Input Pin No. Signal Pin No. Signal Not connected Hot plug detection Not connected Not connected Not connected Not connected Not connected Not connected Not connected... -
Page 81: (Rs-232C) Specifications And Command Settings
(RS-232C) Specifications and Command Settings PC control A computer can be used to control the projector by connecting an RS-232C cable (null modem, cross type, commercially available) to the projector. (See page 23 for connection.) Communication conditions Set the serial port settings of the computer to match that of the table. - Page 82 INPUT 1 (COMPONENT 1) BRIGHT (–30 – +30) INPUT 1 (COMPONENT 1) COLOR (–30 – +30) INPUT 1 (COMPONENT 1) TINT (–30 – +30) INPUT 1 (COMPONENT 1) SHARP (–30 – +30) INPUT 1 CLR TEMP (55 – 115) INPUT 1 (COMPONENT 1) DISPLAY...
- Page 83 CONTROL CONTENTS COMMAND PARAMETER INPUT 2 GAMMA POSITION : STANDARD INPUT 2 GAMMA POSITION : BLACK DETAIL INPUT 2 GAMMA POSITION : BRIGHTEN INPUT 2 GAMMA POSITION : CUSTOM 1 INPUT 2 GAMMA POSITION : CUSTOM 2 INPUT 2 GAMMA POSITION : SVM GAMMA INPUT 3 GAMMA POSITION : STANDARD INPUT 3 GAMMA POSITION : BLACK DETAIL INPUT 3 GAMMA POSITION : BRIGHTEN...
-
Page 84: Wired Remote Control Terminal Specifications
Data Code System codes C1 to C5 are fixed at “10110”. Codes C14 and C15 are reverse confirmation bits, with “10” indicating “Front” and “01” indicating “Rear”. Sharp remote control signal format Transmission format: 15-bit format 67.5 ms 67.5 ms Wave form of output signal: Output using Pulse Position Modulation “1”... -
Page 85: Computer Compatibility Chart
350 VESA format VGA signals, “640 When projecting video images of an interlace video signal with the projector, the intended image may not be projected depending on the video signal when using the RBG input. In such cases, use the component input, S-video input or video input. -
Page 86: Troubleshooting
Troubleshooting Problem Projector power cord is not plugged into the wall outlet. Power to the external connected devices is off. The selected input mode is wrong. Cables incorrectly connected to rear panel of the projector. Remote control batteries have run out. -
Page 87: For Sharp Assistance (U.s.a Only)
If you encounter any problems during setup or operation of this projector, first refer to the “Trouble- shooting” section on this page. If this operation manual does not answer your question, please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance. Or, send us an e-mail at lcdsupport@sharpsec.com . -
Page 88: Specifications
Lens cap (PCAPHA1056CESA), SharpVision Manager Software CD-ROM (UDSKAA019WJZZ), Projector operation manual (TINS-A440WJZZ), SharpVision Manager operation manual (TINS-A452WJZZ) This SHARP projector uses a DMD Chip. This very sophis- ticated panel contains 921,600 pixels. As with any high tech- nology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. -
Page 89: Dimensions
Dimensions Units: inches (mm) Rear View Side View Top View Side View Front View (475) Bottom View... -
Page 90: Glossary
CUSTOM. Keystone correction Function to digitally correct a distorted image when the projector is set up at an angle, smoothens out jaggies on keystone images and compresses the image not only horizontally but vertically keeping the 4:3 aspect ratio. -
Page 91: Index
Index 2D Progressive ... 46 3D Progressive ... 46 AC socket ... 16 Adjusting Computer Images ... 53 Adjusting the Lens ... 26 Adjusting the Picture ... 44 Adjustment buttons ... 32 Adjustment feet ... 25 Aspect ratio ... 59 Auto Power off ... - Page 92 Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than an authorized servicer.
-
Page 93: Limited Warranty
VALID IN CANADA ONLY LIMITED WARRANTY Consumer Electronics Products Congratulations on your purchase! WARRANTY PERIODS...