Related Manuals for Siemens FDK:085U0321
Summary of Contents for Siemens FDK:085U0321
- Page 1 Communication Modules Add-on modules HART Operating Instructions • 07/2010 SITRANS F...
-
Page 3: Table Of Contents
HART add-on module Contents Introduction ............3 Scope . -
Page 4: Introduction
1. Introduction / 2. Device Identification HART add-on module Introduction The Siemens HART interface for use with SITRANS F flow transmitters: MAG 5000 C, MAG 6000 Scope and MASS 6000, revision 2, complies with HART protocol Revision 5.2. This document specifies all the device specific features and documents HART Protocol implementation details (e.g. -
Page 5: Product Overview
3. Product overview HART add-on module All interfaces apply to the following specifications: Manufacturer Siemens Device Type 24 = MAG5/6000 + variants Name: Codes: 25 = MASS 6000 Manufacturer ID 42 (2A hex) code: HART Protocol Device Revision: 2 revision:... -
Page 6: Product Interfaces
HART add-on module 4. Product interfaces Product interfaces Mechanical The MAG 5000 C HART is delivered with a build-in HART interface. It is not possible to add Installation additional modules to the MAG 5000 C. MAG 5000 C HART Before proceeding, please make sure that you have the right HART Add-on module. The Mechanical Installation correct module for MAG 6000 and MASS 6000 is FDK:085U0226. -
Page 7: General Electrical Information
4. Product interfaces HART add-on module General electrical On the electrical termination boards for USM II transmitters, additional input/output terminals have been reserved for add-on module functions. The numbering range of these terminals information is as follows, but how many are actually used depends on the type of add-on module. Please refer to the relevant handbook for other electrical connection information. -
Page 8: 4.5.2 Mass 6000
HART add-on module 4. Product interfaces In single Pant mode the Current output will have the behaviour as described in the table below. Parameter Selection Comment Current output: The Current output is active. ON is selected automatically during power up. The Current output is deactivated. -
Page 9: Local Display
HART add-on module 4. Product interfaces Local display When the HART module is inserted in the device, and the transmitter is powered up, a new menu entry is available. The new menu hold all HART relevant information. To change (or view) the HART settings from the keypad display. Press [Top key] for two seconds. -
Page 10: Menu Item Explanation
HART add-on module 4. Product interfaces / 5. Device Variables / 6. Dynamic Variables 4.6.1 Menu item The table below describes submenus under the main menu „HART module“. explanation Item Value Description HART 0-15 Device address [Factory setting: 00] short address TAG name 8 characters Can be used to TAG the device. -
Page 11: Status Information
7. Status Information HART add-on module Status Information This chapter defines all status provided by the flowmeter including: the Device status byte; the Extended Device Status byte; and status information returned in Command 48. Device status Definition Device Malfunction – The device detected a serious error or failure that compromises device operations. -
Page 12: Universal Commands
HART add-on module 8. Universal Commands Universal This device supports the following Universal Commands. Commands Command Number Data in Command Data in Response and Funktion 0 Read unique identifier None Byte 0 "254" (expansion) Byte 1 Manufacturer ID Byte 2 Mfr. -
Page 13: Common-Practice Commands
9. Common-Practice Commands HART add-on module Common-Practice This device supports the following Common-Practice Commands. Commands Command Number and Data in Command Data in reply Function 33 Read transmitter variables Not implemented 34 Write damping value Byte 0-3 Byte 0-1 As in command Damping value in sec. -
Page 14: Device-Specific Commands
10. Device-Specific Commands HART add-on module Device-Specific This device supports the following Device-Specific Commands. Except from command 170 and Commands 171, these commands are reserved for software tools like PDM, AMS and HC275/375. Command Number and Data in Command Data in reply Function 128 Read Integer8 Byte 0... - Page 15 10. Device-Specific Commands HART add-on module Command Number and Data in Command Data in reply Function 141 Write Integer8 Byte 0 CANAPP.ID Byte 0 Integer value Byte 1 Attribute.ID Byte 2 Attribute Qual Byte 3 Reserved (0x00) Byte 4-5 Index (2 bytes) Byte 6 Integer8 142 Write Integer16...
- Page 16 10. Device-Specific Commands HART add-on module Command Number and Data in Command Data in reply Function 171 Read totalizer Byte 0 Totalizer no. Byte 0 Unit code 0 = Totalizer 1 Byte 1-4 Totalizer value 1 = Totalizer 2 Byte 5 Totalizer no.
- Page 17 10. Device-Specific Commands HART add-on module Command Number and Data in Command Data in reply Function 185 Read Relayoutput1 None MAG 5000 C/6000 Byte 0 0 = Off 3 = Error level 4 = Error number 5 = Direction/Limit 6 = Batch 7 = Cleaning MASS 6000 Byte 0...
-
Page 18: Tables
11. Tables HART add-on module Tables 11.1 Volume flow Unit code Description Note unit codes Cubic feet per minute US gallons per minute Liters per minute UK gallons per minute Cubic meters per hour US gallons per second Million US gallons per day Liters per second Million liters per day Cubic feet per second... -
Page 19: Volume Unit Codes
Tables HART add-on module 11.2 Volume unit codes Unit code Description Note Gallons Liters Imperial gallons Cubic meters Barrels 41 USG Bushels Cubic yards Cubic feet BBL liquid 31,5 USG Normal cubic meters Same as Cubic meters Normal liters Same as liters Standard cubic feet Same as cubic feet Hector liters... -
Page 20: Density Unit Codes
QV digital calculation (Volume flow) 2 per second Analog output update 30 per second Annex A Manufacturer Siemens Capability Checklist Model SITRANS F M Magflo MAG 5000 C SITRANS F M Magflo MAG 6000 SITRANS F C Massflo MASS 6000... -
Page 21: Annex B - Default Configuration
For more information www.siemens.com/flow Siemens A/S Subject to change without prior notice *A5E03089708* Flow Instruments Order No.: A5E03089708 Nordborgvej 81 Lit. No.: A5E03089708-01 DK-6430 Nordborg SFIDK.PS.023.F2.02 © Siemens AG 07.2010 www.siemens.com/processautomation...