Siemens CL-010 User Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Network Router
  5. CL-010
  6. User manual
Siemens CL-010 User Manual

Siemens CL-010 User Manual

Adsl2+ router
Hide thumbs
Table of Contents

Advertisement

Quick Links

CL-010/CL-010-I ADSL2+ Router
User's Manual
Rev: 1.5
2007/03/30
No part of this publication may be reproduced in any form by any means without the prior written permission. Other
trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies.
This manual currently suits for CL-010/CL-010-I.

Advertisement

Table of Contents
loading

Related Manuals for Siemens CL-010

Summary of Contents for Siemens CL-010

  • Page 1 No part of this publication may be reproduced in any form by any means without the prior written permission. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies. This manual currently suits for CL-010/CL-010-I.

  • Page 2: Safety Notes

    Safety Notes For Installation For Using Do not attempt to disassemble or open covers of this unit by yourself. Nor should you For Service attempt to service the product yourself, which may void the user’s authority to operate it. Contact qualified service personnel under the following conditions: Warning Caution Use only the type of power source indicated on the marking labels.

  • Page 3: Fcc Class B Notice

    FCC Class B Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

  • Page 4: Adsl Compliance

    CL-010/CL-010-I ADSL2+ Router is a DSL broadband access device which allows ADSL2+ connectivity capabilities for home or office users. It supports ADSL2/ADSL2+ and is backward compatible to ADSL, even offers auto-negotiation capability for different flavors (G.dmt, G.lite, or...

  • Page 5: Bridging Features

    RFC2684 LLC Encapsulation and VC Multiplexing over AAL5 RFC2364 Point-to-Point Protocol (PPP) over AAL5 RFC2225 Classical IP and ARP over ATM RFC2516 PPP over Ethernet: support Relay (Transparent Forwarding and Client functions) Support PPPoA or PPPoE Bridged mode (the IP address got from ISP can be passed to the user’s PC and behave as the IP address of the user’s PC.) OAM F4/F5 End-to-End/Segment Loopback Cells Bridging Features...
  • Page 6 Firmware upgrades through HTTP, TFTP, or FTP The boot loader contains very simple web page to allow the users to update the run-time firmware image. Configuration file backup and restore SNMPv1/v2 agent with MIB-II, ADSL Line MIB Unpacking Check the contents of the package against the pack contents checklist below. If any of the items is missing, then contact the dealer from whom the equipment was purchased.

  • Page 7: Subscription For Adsl Service

    ADSL Router User Manual Subscription for ADSL Service To use the ADSL Router, you have to subscribe for ADSL service from your broadband service provider. According to the service type you subscribe, you will get various IP addresses: Dynamic IP: If you apply for dial-up connection, you will be given an Internet account with username and password.

  • Page 9: Chapter 1: Overview

    Chapter 1: Overview This chapter provides you the description for the LED and connector for front and rear view of the router. Before you use/install this router, please take a look at this information first. Physical Outlook Front Panel The following illustrations show the front panel of the ADSL Router: LED Indicators The ADSL Router is equipped with five LEDs on the front panel as described in the table below (from left to right):...

  • Page 10: Rear Panel

    Rear Panel The following figures illustrate the rear panel of your ADSL Router. 9 VAC Connector Description 9 VAC Power connector 9VAC Power switch Ethernet RJ-45 connector Ethernet RJ-11 connector...

  • Page 11: Installation

    Chapter 2: System Requirement and System Requirement To access the ADSL Router via Ethernet, the host computer must meet the following requirements: The ADSL Router is configured with the default IP address of 192.168.1.1 and subnet mask of 255.255.255.0. As the DHCP server is Enable by default, The DHCP clients should be able to access the ADSL Router.

  • Page 12: Connecting The Adsl Router

    Connecting the ADSL Router Follow the steps below to connect the related devices. Connecting the ADSL line. Connect the DSL port of the device to your ADSL wall outlet with RJ-11 cable. Please attach one end of the Ethernet cable with RJ-45 connector to the LAN port of your ADSL Router.

  • Page 13: Setting Tcp/Ip

    For connecting through a hub, please refer to the following diagram for an example. 9 VAC Setting TCP/IP In order to access the Internet through the router, each host on your network must install/setup TCP/IP. Please follow the steps below for select a network adapter.

  • Page 14: For Windows 98

    For Windows 98 Click on the Start menu, point to Settings and click on Control Panel. Double-click the Network icon The Network window appears. On the Configuration tab, check out the list of installed network components. Option 1: If you have no TCP/IP protocol, click Add.
  • Page 15 On the left side of the windows, highlight Microsoft and then select TCP/IP on the right side. Then click OK When returning to Network window, highlight TCP/IP protocol for your NIC and click Properties. On IP Address tab: Enable Specify an IP address option. Enter the IP Address: 192.168.1.x (x is between 2 and 254) and Subnet Mask: 255.255.255.0 as in figure below.
  • Page 16 When returning to Network window, click OK Wait for Windows copying files. When prompted with System Settings Change dialog box, click Yes to restart your computer.

  • Page 17: For Windows Me

    For Windows ME 1. Click on the Start menu, point to Settings and click on Control Panel. 2. Double-click the Network icon. 3. The Network window appears. On the Configuration tab, check out the list of installed network components. Option 1: If you have no TCP/IP protocol, click Add.

  • Page 18: For Windows Nt

    9. Wait for Windows copying files. 10. When prompted with the System Settings Change dialog box, click Yes to restart your computer. For Windows NT 1. Click Start, point to Settings, and then click Control Panel. 2. Double-click the Network icon. 3.
  • Page 19 5. Click Yes to use DHCP. 6. Insert the Windows NT CD into your CD-ROM drive and type the location of the CD. Then click Continue. 7. Returning to the Network window, you will find the TCP/IP Protocol among the list. Select TCP/IP Protocol and click Properties.
  • Page 20 When returning to Network window, click Close. When prompted with Network Settings Change dialog box, click Yes to restart your computer.

  • Page 21: For Windows 2000

    For Windows 2000 From the Start menu, point to Settings and then click Network and Dial-up Connections. Right-click the Local Area Connection icon and then click Properties. On the General tab, check out the list of installed network components. Option 1: If you have no TCP/IP Protocol, click Install.
  • Page 22 Highlight Protocol and then click Add. Click Internet Protocol (TCP/IP) and then click OK. When returning to Local Area Connection Properties window, highlight Internet Protocol (TCP/IP) and then click Properties. Under the General tab, enable Use the following IP Address. Enter the IP address: 192.168.1.x (x is between 2 and 254), Subnet Mask: 255.255.255.0 and Default gateway:...

  • Page 23: For Windows Xp

    For Windows XP From the Start menu, point to Control Panel and then click Network and Internet Connections. Click Network Connection and then click Properties. Click Network Connection and then click Properties.3.On the General tab, check out the list of installed network components.

  • Page 24: For Windows Vista

    For Windows Vista Open the Start menu, point to Control Panel and click Click Network and Internet. Select Network and Sharing Center.
  • Page 25 Click Manage Network Connection on the left side. Right click Local Area Connection and select Properties. On the Networking tab, you will find Internet Protocol Version 6 and Version 4. Contact your ISP to confirm which one will be used. (We take TCP/IPv4 for example here.) Select Internet Protocol...

  • Page 26: Renewing Ip Address On Client Pc

    Under the General tab, enable Use the following IP address. Enter the IP address: 192.168.1.x (x is between 2 and 254), Subnet Mask: 255.255.255.0 and Default gateway: 192.168.1.1. Then click Ok. Renewing IP Address on Client PC After the ADSL Router gets on line, there is a chance that your PC does not renew its IP address and thus causes the PC not able to access the Internet.
  • Page 27 Chapter 3: Configuration On the IP Address tab, select Obtain an IP address automatically. Then click OK. For Windows ME On the IP Address tab, select Obtain an IP address automatically. Then click OK.
  • Page 28 For Windows NT On the IP Address tab, click on the drop-down arrow of Adapter to select required adapter. Enable Obtain an IP address from a DHCP server and then click OK.. When prompted with the message below, click Yes to continue. For Windows 2000 Enable Obtain an IP address automatically and then click OK.

  • Page 29: Windows Vista

    Chapter 3: Configuration For Windows XP On the IP Address tab, select Obtain an IP address automatically. Then click OK. Windows Vista On the IP Address tab, select Obtain an IP address automatically. Then click OK.

  • Page 30: Renew Ip Address On Client Pc

    Renew IP Address on Client PC There is a chance that your PC does not renew its IP address after the ADSL Router is on line and the PC cannot access the Internet. Please follow the procedures below to renew PC’s IP address. For Windows 98ME 1.
  • Page 31 2. Select Run from the Start menu. 3. Type cmd in the dialog box and the click 4. Type ipconfig at prompt. Then you will see the IP information from DHCP server. 5. If you want to get a new IP address, type ipconfig /release to release the previous IP address and then type ipconfig /renew to get a new one.
  • Page 32 For Windows 2000 1. From the Start menu, point to Programs, Accessories and then click Command Prompt. 2. Type ipconfig at prompt. Then you will see the IP information from DHCP server. 3. If you want to get a new IP address, type ipconfig /release to release the previous IP address and then type ipconfig /renew to get a new one.
  • Page 33 For Windows Vista 1. Open the Start menu, and type cmd in the text box then click OK. 2. The command prompt window will appear. 3. Type ipconfig at the command window and press Enter to view the computer’s IP information from DHCP server.
  • Page 34 Note: If you cannot release the IP address successfully and see the message “The requested operation requires elevation,” please go to the Start menu and right click Command Prompt, then set Run as administrator. Press Continue when a dialog asking for permission to continue prompts.

  • Page 35: Chapter 3: Connecting And Accessing

    Chapter 3: Connecting and Accessing Prior to configuring the ADSL Router, you must decide whether to configure the ADSL Router as a bridge or as a router. This chapter presents some deployment examples for your reference. Each mode includes its general configure procedures. For more detailed information about web configuration, refer to "Web Configuration".

  • Page 36: Ppp Over Atm (Pppoa) Mode

    PPP over ATM (PPPoA) Mode STM-1 (Internet Service Provider) BRAS RDAIUS Server *BRAS: Broadband Remote Access Server Description: In this deployment environment, the PPPoA session is between the ADSL WAN interface and BRAS. The ADSL Router gets a public IP address from BRAS when connecting to DSLAM. The multiple client PCs will get private IP address from the DHCP server enabled on private LAN.

  • Page 37: Ppp Over Atm (Pppoa) Ip Extension Mode

    PPP over ATM (PPPoA) IP Extension Mode STM-1 (Internet Service Provider) BRAS RDAIUS Server *BRAS: Broadband Remote Access Server Description: In this deployment environment, the PPPoA session is between the ADSL WAN interface and BRAS. The ADSL Router acts as a bridge and gets a public IP address from BRAS for your computer. And only the one that got the public IP address is allowed to access into Internet.

  • Page 38: Ppp Over Ethernet (Pppoe) Mode

    PPP over Ethernet (PPPoE) Mode STM-1 (Internet Service Provider) BRAS RDAIUS Server *BRAS: Broadband Remote Access Server Description: In this deployment environment, the PPPoE session is between the ADSL WAN interface and BRAS. The ADSL Router gets a public IP address from BRAS when connecting to DSLAM. The multiple client PCs will get private IP address from the DHCP server enabled on private LAN.

  • Page 39: Ppp Over Ethernet (Pppoe) Ip Extension Mode

    PPP over Ethernet (PPPoE) IP Extension Mode (Internet Service Provider) STM-1 BRAS RDAIUS Server *BRAS: Broadband Remote Access Server Description: In this deployment environment, the PPPoE session is between the ADSL WAN interface and BRAS. The ADSL Router acts as a bridge and gets a public IP address from BRAS for your computer. And only the one that got the public IP address is allowed to access into Internet.

  • Page 40: Numbered Ip Over Atm (Ipoa)

    Numbered IP over ATM (IPoA) STM-1 (Internet Service Provider) BRAS RDAIUS Server *BRAS: Broadband Remote Access Server Description: If you apply for multiple IP addresses from your ISP, you can assign these public IP addresses to the ADSL Router and public server, e.g., Web or FTP server. Typically the first IP is network address, the second is used as router IP address and the last one is subnet broadcasting.
  • Page 41 Check the network information. Make sure the settings match the settings provided by ISP. Click Finish. Set TCP/IP for your computer. Specify an IP Address, subnet mask and set default gateway. eg: IP Address: 10.3.75.51 Subnet Mask: 255.255.255.248 Gateway: 10.3.75.49 Now the router is well configured.

  • Page 42: Numbered Ip Over Atm (Ipoa)+Nat

    Numbered IP over ATM (IPoA)+NAT Description: In this deployment environment, we make up a private IP network of 192.168.1.1. NAT function is enabled (on ADSL Router or use another NAT box connected to hub) to support multiple clients to access the Router and some public servers (WWW, FTP). If you apply for multiple IP addresses from your ISP, you can assign these public IP addresses to the ADSL Router and public server, e.g., Web or FTP server.
  • Page 43 LAN. Primary IP Address: 192.168.1.1 Subnet mask: 255.255.255.0 Start IP Address: 192.168.1.2 End IP Address: 192.168.1.254 Check Configure the second IP Address and Subnet Mask for LAN Interface and type in the second IP address and subnet mask. Then click Next. Secondary IP Address: 10.3.75.49 Subnet mask: 255.255.255.248 Check the network information.

  • Page 44: Unnumbered Ip Over Atm (Ipoa)

    Unnumbered IP over ATM (IPoA) STM-1 (Internet Service Provider) BRAS RDAIUS Server *BRAS: Broadband Remote Access Server Description: If you apply for multiple IP addresses from your ISP, you can assign these public IP addresses to the ADSL Router and public server, e.g., Web or FTP server. Typically the first IP is network address, the second is used as router IP address and the last one is subnet broadcasting.
  • Page 45 Set TCP/IP for your computer. Specify an IP Address, subnet mask and set default gateway. eg: IP Address: 10.3.75.51 Subnet Mask: 255.255.255.248 Gateway: 10.3.75.49 Now the router is well configured. You can access into Internet.

  • Page 46: Unnumbered Ip Over Atm (Ipoa)+Nat

    Unnumbered IP over ATM (IPoA)+NAT Description: If you apply for multiple IP addresses from your ISP, you can assign these public IP addresses to the ADSL Router and public server, e.g., Web or FTP server. Typically the first IP is network address, the second is used as router IP address and the last one is subnet broadcasting.
  • Page 47 Start IP Address: 192.168.1.2 End IP Address: 192.168.1.254 Check Configure the second IP Address and Subnet Mask for LAN Interface and type in the second IP address and subnet mask. Then click Next. Secondary IP Address: 10.3.75.49 Subnet mask: 255.255.255.248 Check the network information.

  • Page 48: Bridge Mode

    Bridge Mode STM-1 (Internet Service Provider) BRAS RDAIUS Server *BRAS: Broadband Remote Access Server Description: In this example, the ADSL Router acts as a bridge which bridging PC IP address from LAN to WAN. PC IP address can be a static public address that is pre-assigned by ISP or a dynamic public address that is assigned by ISP DHCP server, or can be got from PPPoE software.

  • Page 49: Chapter 4: Web Configuration

    Chapter 4: Web Configuration Some users might want to set specific configuration for the router such as firewall, data transmission rate… and so on. This chapter will provide you advanced information of the web pages for the router for your reference. Using Web-Based Manager Once your host PC is properly configured, please proceed as follows: 1.

  • Page 50: Outline Of Web Manager

    Outline of Web Manager For configure the web page, please use admin as the username and the password. The main screen will be shown as below. Title: It indicates the title of this management interface. Main Menu: Includes Quick Start, Status, Advanced and Management. Main It is the current workspace of the web management, containing configuration or status Window:...

  • Page 51: Quick Start

    Chapter 5:Connection Mode Quick Start The pages for the Quick Start provide user a quick way to set for the router. If you do not know more about the router, you can use the Quick Start pages to adjust basic settings to make your router activating.
  • Page 52 After clicking on the Next button from the VPI/VCI web page, the following screen will appear. Please choose the connection type and encapsulation mode that you want to use and click Next for next page. For example, PPP over Ethernet (PPPoE) in this screen is selected.

  • Page 53: Ppp Over Atm/ Ppp Over Ethernet

    Chapter 5:Connection Mode PPP over ATM/ PPP over Ethernet If the type you choose is PPP over ATM or PPP over Ethernet, please refer to the following information. According to the ISP’s configuration on the server, you can choose PPPoE and PPPoA modes.
  • Page 54 PPP Username: Type in the username that you got from your ISP. PPP Password: Type in the password that you got from your ISP. Always On: Check this button to make the connection is always active. Dial on Demand: Click this button to make a connection while in demand.
  • Page 55 Chapter 5:Connection Mode PCs. Start IP Address: Type in the start point IP address. End IP Address: Type in the end point IP address. Leased Time: Type in the duration for the time. The default is 1day. DHCP Server Off: Check this item if DHCP service isn’t needed on the LAN.

  • Page 56: Ip Over Atm

    IP over ATM If the type you have to choose is IP over ATM, please refer to the following information. IPoA is an alternative of LAN emulation. It allows TCP/IP network to access ATM network and uses ATM quality of service’s features.
  • Page 57 In the Configure LAN side Settings web page, you have to fill in the data requested here. Primary IP Address: Type in the first IP address that you got from your ISP for your LAN connection. Subnet Mask: Type in the subnet mask that you got from your ISP for your LAN connection.
  • Page 58 Now, the system will reboot to activate the new settings that you have done in this section. Please wait for 2 minutes for restarting the router.
  • Page 59 Chapter 5:Connection Mode Bridging If the type you choose is Bridging, please refer to the following information. The bridging mode can configure your router to send packets received on any port such as ATM PVC or Ethernet with a broadcast MAC address to all other ports.
  • Page 60 Primary IP Address: Type in the IP address that you got from your ISP for LAN interface. Subnet Mask: Type in the subnet mask that you got from your ISP for LAN interface. MTU: It means the maximum size of the packet that transmitted in the network.
  • Page 61 Chapter 5:Connection Mode Status Overview This page is displaying the current status for the DSL connection. It includes if the lists the LAN IP address, default gateway, DNS servers IP address, firmware version, the period of activating the router, and so on. The system status will be changed according to the settings that you configured in the web pages.

  • Page 62: Adsl Line

    ADSL Line This page shows all information for ADSL. For knowing the quality of the ADSL connection, please click ADSL BER Test button to have advanced information. Click More Information to show more detailed information about ADSL Line Status. ADSL BER Test This test determines the quality of the ADSL connection.

  • Page 63: Internet Connection

    Chapter 5:Connection Mode When the test is over, the result will be shown on the following dialog for your reference. Click Close to close this dialog. Internet Connection This page displays the connection information for your router, such as PVC name, category, protocol, invoking NAT or not, IP address, link status and so on.
  • Page 64 This table shows the IP address record for IP-to-Physical translation in your router.

  • Page 65: Local Network - Dhcp Server

    Chapter 5:Connection Mode Advanced Setup Local Network- IP Address This page is the same as you can see in the Configure LAN side Settings page while running the Quick Setup. It allows you to set IP Address and Subnet Mask values for LAN interface. Primary IP Address: Type in the first IP address that you got from your ISP for your LAN connection.
  • Page 66 DHCP Server On: Check this item if DHCP service is needed on the LAN. The router will assign IP address, gateway address for each of your PCs. Start IP Address: Type in the start point IP address. End IP Address: Type in the end point IP address.
  • Page 67 Chapter 5:Connection Mode The new one will be shown on the dialog right away. That is, the specified address will be reserved and not be assigned by DHCP for other computer.

  • Page 68: Local Network - Upnp

    Local Network – UPnP The UPnP is available only for Windows XP. If you are not user of Windows XP, this page does not have any meaning to you. This page allows you to enable the UPnP function through the web page for your router.
  • Page 69 Chapter 5:Connection Mode If you choose Non Realtime VBR, you have to type in the following data. The range for Peak Cell Rate is from 1 to 1690. The range for Sustainable Cell Rate is from 1 to 1689 and must be smaller than Peak Cell Rate.

  • Page 70: Internet-Dns Server

    Internet-DNS Server If Enable Automatic Assigned DNS checkbox is selected, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If the checkbox is not selected, it is necessary for you to enter the primary and optional secondary DNS server IP addresses.

  • Page 71: Internet - Adsl Settings

    Chapter 5:Connection Mode Internet - ADSL Settings Enable ADSL Port: Check this box to enable this function. It simply invokes the line mode that you choose here for the router. Select the support of line modes: There are several selections for your choosing.

  • Page 72: Configuring Other Routers On Your Lan

    Allow you to remove the selected static route settings. Adding a New One To add a static route, please choose Static Route - Add. Type the destination network address, subnet mask and gateway that you get from ISP and click Apply. Destination Network Address: The destination IP address of the network where data packets are to be sent.

  • Page 73: Ip Routing - Dynamic Routing

    For a router with a direct connection to the Router’s local Router, the Gateway IP Address is the address of the Router’s local router. For routers which must forward packets to another router before reaching the Router’s local router, the Gateway IP Address is the address of the intermediate router. Example –...
  • Page 74 different interface. Otherwise, disable this function. Click Apply to invoke the settings set here.

  • Page 75: Virtual Server-Port Forwarding

    Virtual Server-Port Forwarding The Router implements NAT to let your entire local network appear as a single machine to the Internet. The typical situation is that you have local servers for different services and you want to make them publicly accessible. With NAT applied, it will translate the internal IP addresses of these servers to a single IP address that is unique on the Internet.

  • Page 76: Ip Address Seen By Internet Users

    IP Address seen by Internet Users Please note that, in the above picture, both Internet users are connecting to the same IP address, but using different protocols. To Internet users, all virtual servers on your LAN have the same IP Address. This IP Address is allocated by your ISP.

  • Page 77: Connecting To The Virtual Servers

    Chapter 5:Connection Mode From Internet Host IP Address: Select the initial place for port forwarding. If you choose SINGLE, a box will appear for you to fill in the IP address for the specific host. And, if you choose SUBNET, the boxes of IP and Subnet will appear for you to fill in the IP address and subnet mask for the specific host as the start point.

  • Page 78: Virtual Server - Dmz Host

    Or define by yourself by typing the words into the field of User defined. Click Apply to complete the setting. Virtual Server - DMZ Host Direct Mapping Zone (DMZ) uses a technology that makes Router forwarding all incoming packet to internal specific server. To close the function of DMZ Host, please click Discarded.

  • Page 79: Virtual Server - Dynamic Dns

    Chapter 5:Connection Mode Virtual Server - Dynamic DNS The Dynamic DNS (Dynamic Domain Nasme System) combines both functions of DNS and DHCP to map a dynamic IP into a fixed domain name. This page allows you to access into virtual servers with a domain name and password.
  • Page 80 Firewall The firewall is a software that interrupts the data between the Internet and your computer. It is the TCP/IP equivalent of a security gate at the entrance to your company. All data must pass through it, and the firewall (functions as a security guard) will allow only authorized data to be passed into the LAN.
  • Page 81 Chapter 5:Connection Mode Then, to add a new IP Filtering, click Add. This page provides some settings for you to adjust for adding a new outbound IP Filtering. Allow Traffic: No stops the data transmission, Yes lets the data pass through. Protocol: Here provide several default policies for security levels for you to choose.

  • Page 82: Quality Of Service

    A new IP filtering setting for Outbound traffic is created in the web page. To edit the setting, please click the pencil mark to get into the editing page. To delete the setting, click the trash mark to erase it. To set another IP filtering, click Add again.
  • Page 83 Chapter 5:Connection Mode is the default setting. IP type of Service: The system provides some types of service for you to choose. The meaning of each type is the same as the denotation. The default one is No change. IPQoS To classify the upstream traffic by assigning the transmission priority of the data for different users, please use IP QoS to...

  • Page 84: Port Mapping

    you want to invoke the QoS traffic rule. Destination Port: Type in the destination port for the traffic rule. The range is from 0 to 65535. Traffic Priority: There are three options – Low, Medium, and High that you can choose. It decides the order of each data transmitted through this device.
  • Page 85 Chapter 5:Connection Mode Group Name: Type in a name here as a group name. It must be unique. The word length must not be over the length of the field. Available Interfaces: The available interfaces (such as Ethernet) will be displayed in the left side box. When you choose it and click Add, it will be transferred into the right side box of Grouped Interfaces.
  • Page 86 Chapter 5:Connection Mode Management Diagnostics To check the link status for the network and your computer, a diagnostic test can guide you to detect the network problem. The testing items are listed and accomplished one by one. If the previous one is failed, than the items below that failed one will be failed too.

  • Page 87: Admin Account

    Chapter 5:Connection Mode Admin Account This page allows you to type in the password for accessing into your DSL Router. For the Admin Account, the default setting for user password is admin. If you want to change the username and the password, please retype the new password in the Confirm field for confirmation.

  • Page 88: Interntet Time

    Interntet Time The router’s clock must synchronize with global Internet’s time. The time you set in the screen will be adapted to system log. Update: Click this button to refresh the current time. Set Time by: The default setting is Manual. If you select Time Server, you don’t need to type in the time setting manually.

  • Page 89: Viewing System Log

    Chapter 5:Connection Mode There are 8 types for log level and display level for your choose. The default is Debugging. The mode selection includes Local, Remote and Both. The default one is Local. If you choose Remote or Both, all the events will be sent to the specified UDP port of the specified log server.

  • Page 90: Snmp Setting

    SNMP Setting The SNMP, the abbreviation of Simple Network Management Protocol, is used to refer to a collection of specifications for network management that include the protocol itself, the definition of data structures and associated concepts. A management station performs the monitoring function by retrieving the value of MIB objects. The management station and agents are linked by a network management protocol that is SNMP.

  • Page 91: Backup Config

    Chapter 5:Connection Mode workstation by way of SNMP agent. Backup Config To backup your configuration for the router to your computer, you can use Backup Config web page to save the settings. And when you want to restore the settings in the future, simply open Backup Config web page and use Browse button to locate the file and click Restore.

  • Page 92: Upnp For Xp

    UPnP for XP Universal plug and play (UPnP) is an architecture for pervasive peer to peer network connectivity of intelligent appliances and PCs of all form factors. It is designed to bring easy-to-use, flexible, standards-based connectivity to ad-hoc or unmanaged networks whether in the home, in a small business, public spaces, or attached to the Internet.
  • Page 93 Chapter 5:Connection Mode 7. Now, the NAT traversal function will be provided. The ADSL router will create a new virtual server automatically for mapping while the router detecting the computer running some Internet applications.

  • Page 94: Chapter 5: Troubleshooting

    Chapter 5: Troubleshooting If the suggested solutions in this section do not resolve your issue, contact your system administrator or Internet service provider. Problems with LAN PCs on the LAN cannot get IP addresses from the ADSL Router. The chances are that the interface used as DHCP server is modified and the client PCs do not renew IP addresses.

  • Page 95: Problems With Upgrading

    Request time out Then the DNS is not reachable. Check your DNS setting on the ADSL Router. Problems with Upgrading The following lists the error messages that you may see during upgrading and the action to take. Error: All the ADSL LEDs light up and cannot light off as usual. Possible cause: When users execute firmware upgrade and save settings to the router, the power for the router is lost for some unknown reasons, the normal web page for the router might be damaged.

  • Page 96: Chapter 6: Glossary

    ARP (Address Resolution Protocol ) ARP is a TCP/IP protocol for mapping an IP address to a physical machine address that is recognized in the local network, such as an Ethernet address. A host wishing to obtain a physical address broadcasts an ARP request onto the TCP/IP network.

  • Page 97: Private Ip Address

    configured and mapped to a private workstation address when accesses are made through the gateway to a public network. For example, the ADSL Router is assigned with the public IP address of 168.111.2.1. With NAT enabled, it creates a Virtual LAN. Each PC on the Virtual LAN is assigned with a private IP address with default value of 192.168.1.2 to 192.168.2.254.
  • Page 98 the cells belonging to the same connection can be distinguished. A unique and separate VPI/VCI identifier is assigned in advance to indicate which type of cell is following, unassigned cells, physical layer OAM cells, metasignaling channel or a generic broadcast signaling channel.
  • Page 99 Chapter 7: Glossary...

  • Page 100: Appendix A: Specifications

    Appendix A: Specifications Interface One RJ-11 port for ADSL connection Four RJ-45 ports for IEEE 802.3/802.3u 10/100 Base-T auto-sensing and auto-crossover Ethernet connection One hidden reset button for restoring to factory default settings Regulatory EMI: FCC part 15 Class B, CE Approvals and Immunity: FCC part 68 Class B Compliance...
  • Page 101 Appendix A: Specifications...

  • Page 102: Appendix B: Server Setup For 802.1X Client

    Appendix B: Server Setup for Getting Client Certificate Please connect the client to a network that doesn’t require port authentictaion. Open up Microsoft Explorer in Windows XP, and go to http://<yourserver>/certsrv. Authenticate to the server using your account that you created at the end of the server setup.
  • Page 103 Make sure that User certificate request: User Certificate is selected, and click Next. Click Submit in this dialog. Now, you'll see status messages on the screen, then your certificate will be returned to you. Click Install this certificate. You'll receive a confirmation message about accepting the certificate, click...

  • Page 104: Appendix C: Weee - B2C

    For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service, the shop where you purchased the product or your SIEMENS partner. The statements quoted above are only fully valid for equipment which is installed in the countries of the European Union and is covered by the directive 2002/96/EC.

This manual is also suitable for:

Cl-010-iCl-110Cl-110-i

Table of Contents