Page 2 Information in this document is subject to change without notice. Reproduction of this document in any manner, without the written permission of the D-Link Corporation, is strictly forbidden. Trademarks used in this text: D-Link and the D-Link logo are trademarks of the D-Link Corporation; Microsoft and Windows are registered trademarks of the Microsoft Corporation.
Page 3: Table Of Contents
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Table of Contents Introduction ................................... 1 Audience .................................... 1 Other Documentation ................................. 1 Conventions ..................................1 Notes, Notices, and Cautions ............................1 Web-based Switch Configuration ..........................3 Management Options ................................. 3 Connecting using the Web User Interface .........................
Page 4 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide SNMP ....................................34 SNMP Global Settings ..............................35 SNMP Linkchange Trap Settings ..........................36 SNMP View Table Settings ............................37 SNMP Community Table Settings ..........................38 SNMP Group Table Settings ............................ 39 SNMP Engine ID Local Settings ..........................
Page 5 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Auto Surveillance VLAN ............................. 95 Voice VLAN................................. 98 Spanning Tree ................................101 STP Global Settings ..............................103 STP Port Settings ..............................105 MST Configuration Identification ..........................106 STP Instance ................................107 MSTP Port Information .............................
Page 6 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DSCP Mutation Map ..............................155 Port Trust State and Mutation Binding ........................156 DSCP CoS Mapping ..............................156 CoS Color Mapping ..............................157 DSCP Color Mapping ............................... 158 Class Map ................................. 159 Aggregate Policer ..............................
Page 7 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IMPB ....................................298 IPv4 ................................... 298 IPv6 ................................... 311 DHCP Server Screening ..............................317 DHCP Server Screening Global Settings ......................... 317 DHCP Server Screening Port Settings ........................318 ARP Spoofing Prevention .............................. 319 BPDU Attack Protection ..............................
Page 8 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DDM TX Power Threshold Settings .......................... 356 DDM RX Power Threshold Settings ......................... 357 DDM Status Table ..............................358 11. Monitoring .................................. 359 Utilization ..................................359 Port Utilization ................................359 Statistics ..................................
Page 9: Introduction
Web User Interface (Web UI). The Web UI is the secondary management interface to the DGS-1510 Series switch, which will be generally be referred to simply as “the Switch” within this manual. This manual is written in a way that assumes that you already have the experience and knowledge of Ethernet and modern networking principles for Local Area Networks.
Page 10 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide NOTICE: A notice indicates either potential damage to hardware or loss of data and tells you how to avoid the problem. CAUTION: A caution indicates a potential for property damage, personal injury, or death.
Page 11: Web-Based Switch Configuration
Safari, or Google Chrome. Connecting using the Web User Interface Most software functions of the DGS-1510 Series switches can be managed, configured and monitored via the embedded web-based (HTML) interface. Manage the Switch from remote stations anywhere on the network through a standard web browser. The web browser acts as a universal access tool and can communicate directly with the Switch using the HTTP or HTTPS protocol.
Page 12: Smart Wizard
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide NOTE: The default IP address of this switch is 10.90.90.90, with a subnet mask of 255.0.0.0. Figure 2-1 Displays entering the IP address in Internet Explorer This will open the user authentication window, as seen below.
Page 13 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 2-3 System IP Information window The fields that can be configured are described below: Parameter Description Static Select this option to manually configure and use IP address settings on this switch.
Page 14 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 2-4 SNMP window The fields that can be configured are described below: Parameter Description SNMP Select the Enabled option to enable the SNMP function. Select the Disabled option to disable the SNMP function.
Page 15 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 2-5 SNMP window The fields that can be configured are described below: Parameter Description User Name Enter the username for the new user account here. Privilege Enter the privilege level for the user account here. This value must be between 1 and 15.
Page 16: Web User Interface (Web Ui)
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Web User Interface (Web UI) By clicking the Exit button in the Smart Wizard, you will enter the Web-based Management interface. Areas of the User Interface The figure below shows the user interface. Three distinct areas that divide the user interface, as described in the table.
Page 17: System
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide System Device Information System Information Settings Peripheral Settings Port Configuration PoE (DGS-1510-28P Only) System Log Time and SNTP Time Range Device Information In this window, the Device Information, CPU, and Used status are displayed. It appears automatically when you log in the Switch.
Page 18: Peripheral Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-2 System Information Settings window The fields that can be configured are described below: Parameter Description System Name Enter a system name for the Switch, if so desired. This name will identify it in the Switch network.
Page 19: Port Configuration
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Unit Select the switch unit that will be used for this configuration here. Thermal Select the thermal sensor ID. High Threshold Enter the high threshold value of the warning temperature setting. The range is from -100 to 200 Celsius degree.
Page 20: Port Status
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide From Port / To Port Select the appropriate port range used for the configuration here. State Select this option to enable or disable the physical port here. MDIX Select the Medium Dependent Interface Crossover (MDIX) option here.
Page 21: Port Auto Negotiation
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-5 Port Status window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. Port Auto Negotiation This window is used to view detailed port auto-negotiation information.
Page 22: Error Disable Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-6 Port Auto Negotiation window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 23: Jumbo Frame
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Error Disable Trap Settings are described below: Parameter Description Asserted Select this option to enable or disable the notifications when entering into the error disabled state.
Page 24: Poe (Dgs-1510-28P Only)
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 25: Poe Status
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-9 PoE System window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. Usage Threshold Enter the usage threshold to generate a log and send the corresponding standard notification.
Page 26: Poe Configuration
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-10 PoE Status window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 27: Poe Statistics
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-11 PoE Configuration window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 28: Poe Measurement
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-12 PoE Statistics window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. Click the Clear All button to clear PoE statistics for all ports.
Page 29: Poe Lldp Classification
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-13 PoE Measurement window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. PoE LLDP Classification This window is used to display the PoE LLDP Classification.
Page 30: System Log
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-14 PoE LLDP Classification window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 31: System Log Discriminator Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-15 System Log Settings window The fields that can be configured for Global State are described below: Parameter Description Source Interface State Select this option to enable or disable the source interface’s global state.
Page 32: System Log Server Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-16 System Log Discriminator Settings window The fields that can be configured are described below: Parameter Description Discriminator Enter the discriminator name here. This name can be up to 15 characters long.
Page 33: System Log
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-17 System Log Server Settings window The fields that can be configured are described below: Parameter Description Host IPv4 Address Enter the system log server’s IPv4 address here. Host IPv6 Address Enter the system log server’s IPv6 address here.
Page 34: Time And Sntp
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-19 System Attack Log window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 35 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 3-21 Time Zone Settings window The fields that can be configured are described below: Parameter Description Summer Time State Select the summer time setting. Options to choose from are Disabled, Recurring Setting, and Date Setting.
Page 36: Sntp Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To: Month Select the month that summer time will end. To: Time (HH:MM) Select the time of the day that summer time will end. Offset Enter the number of minutes to add during summer time. The default value is 60.
Page 37: Time Range
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. The fields that can be configured for SNTP Server Setting are described below: Parameter Description IPv4 Address Enter the IP address of the SNTP server which provides the clock synchronization.
Page 38 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete button to remove the specified entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 39: Management
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Management User Account Settings Password Encryption Login Method SNMP RMON Telnet/Web Session Timeout DHCP IP Source Interface File System Physical Stacking Virtual Stacking (SIM) D-Link Discovery Protocol User Account Settings This window is used to create and configure the user accounts.
Page 40: Password Encryption
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-1 User Management Settings window The fields that can be configured are described below: Parameter Description User Name Enter the user account name here. This name can be up to 32 characters long.
Page 41: Login Method
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-3 Password Encryption window The fields that can be configured are described below: Parameter Description Password Encryption State Select this option to enable or disable the encryption of the password before stored in the configuration file.
Page 42: Snmp
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Application Select the application that will be configured here. Options to choose from are Console, Telnet and SSH. Password Type Select the password encryption type that will be used here. Options to choose from are Plain Text and Encrypted.
Page 43: Snmp Global Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Traps Traps are messages that alert network personnel of events that occur on the Switch. The events can be as serious as a reboot (someone accidentally turned OFF the Switch), or less serious like a port status change.
Page 44: Snmp Linkchange Trap Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide SNMP Global State Select this option to enable or disable the SNMP feature. SNMP Response Broadcast Select this option to enable or disable the server to response to Request broadcast SNMP GetRequest packets.
Page 45: Snmp View Table Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-6 SNMP Linkchange Trap Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 46: Snmp Community Table Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-7 SNMP View Table Settings window The fields that can be configured are described below: Parameter Description View Name Type an alphanumeric string of up to 32 characters. This is used to identify the new SNMP view being created.
Page 47: Snmp Group Table Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-8 SNMP Community Table Settings window The fields that can be configured are described below: Parameter Description Key Type Select the key type for the SNMP community. Options to choose from are Plain Text, and Encrypted.
Page 48 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-9 SNMP Group Table Settings window The fields that can be configured are described below: Parameter Description Group Name Enter the group name of a maximum of 32 characters. The syntax is general string that does not allow space.
Page 49: Snmp Engine Id Local Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide SNMP Engine ID Local Settings The Engine ID is a unique identifier used for SNMP V3 implementations on the Switch. To view the following window, click Management > SNMP > SNMP Engine ID Local Settings, as shown...
Page 50: Snmp Host Table Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide identify the SNMP users. Group Name Enter the SNMP group name to which the user belongs. The syntax is general string that does not allow spaces. SNMP Version Select the SNMP version. Options to choose from are v1, v2c, and v3.
Page 51: Rmon
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Host IPv4 Address Enter the IPv4 address of the SNMP notification host. Host IPv6 Address Enter the IPv6 address of the SNMP notification host. User-based Security Model Select the security model here. Options to choose from are SNMPv1, SNMPv2c, and SNMPv3.
Page 52: Rmon Statistics Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Feature. RMON Falling Alarm Trap Select this option to enable or disable the RMON Falling Alarm Trap Feature. Click the Apply button to accept the changes made. RMON Statistics Settings This window is used to configure and display the RMON statistics on the specified port.
Page 53: Rmon History Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide RMON History Settings This window is used to configure and display RMON MIB history statistics gathering on the specified port. To view the following window, click Management > RMON > RMON History Settings, as shown below:...
Page 54: Rmon Event Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click Management > RMON > RMON Alarm Settings, as shown below: Figure 4-18 RMON Alarm Settings window The fields that can be configured are described below:...
Page 55: Telnet/Web
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-19 RMON Event Settings The fields that can be configured are described below: Parameter Description Index Enter the index of the alarm entry between 1 and 65535. Description Enter a description for the RMON event entry. The string is up to 127 characters long.
Page 56: Session Timeout
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-21 Telnet/Web window The fields that can be configured for Telnet Settings are described below: Parameter Description Telnet State Select this option to enable or disable the configuration through Telnet.
Page 57: Dhcp
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide check box to return to the default setting. The value is from 60 to 36000 seconds. The default value is 180 seconds. Console Session Timeout Enter the time in minutes of the web session timeout. Tick the Default check box to return to the default setting.
Page 58 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-24 DHCP Class Settings window The fields that can be configured are described below: Parameter Description Class Name Enter the DHCP class name with a maximum of 32 characters.
Page 59: Dhcp Relay
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCP Relay DHCP Relay Global Settings This window is used to configure the smart relay feature of the DHCP relay agent. To view the following window, click Management > DHCP > DHCP Relay > DHCP Relay Global...
Page 60 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-28 DHCP Relay Pool Source Settings window The fields that can be configured are described below: Parameter Description Source IP Address Enter the source subnet of client packets. Subnet Mask Enter the network mask of the source subnet.
Page 61 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-30 DHCP Relay Pool Class Settings window The fields that can be configured are described below: Parameter Description Class Name Select the DHCP class name. Click the Apply button to accept the changes made.
Page 62 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-32 DHCP Relay Information Settings window The fields that can be configured are described below: Parameter Description Information Trust All Select this option to enable or disable the DHCP relay agent to trust the IP DHCP relay information for all interfaces.
Page 63 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-33 DHCP Relay Information Option Format Settings window The fields that can be configured for DHCP Relay Information Option Format Global are described below: Parameter Description Information Format Remote Select the DHCP information remote ID sub-option.
Page 64: Dhcpv6 Relay
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 65 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-35 DHCPv6 Relay Global Settings window The fields that can be configured are described below: Parameter Description IPv6 DHCP Relay Remote ID Select to choose the sub-type of the remote ID. Options to choose Format from are Default, CID with User Define, and User Define.
Page 66: Dhcp Auto Configuration
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Interface VLAN Enter the VLAN from 1 to 4094 for DHCPv6 relay. Destination IPv6 Address Enter the DHCPv6 relay destination address.
Page 67: Dns Global Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The Domain Name System (DNS) servers are organized in a somewhat hierarchical fashion. A single server often holds names for a single network, which is connected to a root DNS server - usually maintained by an ISP.
Page 68: Dns Name Server Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DNS Name Server Settings This window is used to configure and display the IP address of a domain name server. To view the following window, click Management > DNS > DNS Name Server Settings, as shown below:...
Page 69: Ip Source Interface
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IPv6 Address Select and enter the IPv6 address of the equipment. Click the Apply button to accept the changes made. Click the Delete button to remove the specified entry. IP Source Interface This window is used to configure the IP source interface settings.
Page 70 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-42 File System window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. Path Enter the path string Click the Go button to navigate to the path entered.
Page 71: Physical Stacking
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-44 File System - Copy window When copying a file to the file system of this switch, the user must enter the Source and Destination path. Tick the Replace check box to replace the current running configuration with the indicated configuration file.
Page 72 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-45 Switches stacked in a Duplex Chain...
Page 73 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-46 Switches stacked in a Duplex Ring Within each of these topologies, each switch plays a role in the Switch stack. These roles can be set by the user per individual Switch, or if desired, can be automatically determined by the Switch stack. Three possible roles exist when stacking with the Switch.
Page 74 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Master if the Backup Master is promoted to the Primary Master, or if the Backup Master fails or is removed from the switch stack. If both Primary and Backup masters fail, or are removed from the Switch stack, it will determine if it is to become the Primary Master.
Page 75 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide NOTE: If there is a Box ID conflict when the stack is in the discovery phase, the device will enter a special standalone topology mode. Users can only get device information, configure Box IDs, save and reboot.
Page 76: Virtual Stacking (Sim)
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Virtual Stacking (SIM) D-Link Single IP Management (SIM) is a concept that will stack switches together over Ethernet instead of using stacking ports or modules. There are some advantages in implementing the Single IP Management feature: 1.
Page 77 The CaS can be configured through the CS to become a MS. After configuring one switch to operate as the CS of a SIM group, additional DGS-1510 Series switches may join the group by manually configuring the Switch to be a MS. The CS will then serve as the in band entry point for access to the MS.
Page 78: Single Ip Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 3. This version will support switch upload and downloads for firmware, configuration files and log files, as follows: a. Firmware – The switch now supports MS firmware downloads from a TFTP server.
Page 79: Topology
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Group Name Enter a group name. This is optional. This name is used to segment switches into different SIM groups. Click the Apply button to accept the changes made. The fields that can be configured for SIM Settings are described below:...
Page 80 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-49 Single IP Management window - Tree View The fields that can be displayed are described below: Parameter Description Device Name Display the Device Name of the switches in the SIM group configured by the user.
Page 81 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-50 Topology view This window will display how the devices within the Single IP Management Group connect to other groups and devices. Possible icons on this window are as follows:...
Page 82 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Tool Tips In the Topology view window, the mouse plays an important role in configuration and in viewing device information. Setting the mouse cursor over a specific device in the topology window (tool tip) will display the same information about a specific device as the Tree view does.
Page 83 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-52 Port Speed Utilizing the Tool Tip Right-Click Right-clicking on a device will allow the user to perform various functions, depending on the role of the Switch in the SIM group and the icon associated with it.
Page 84 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-54 Property window The fields that can be displayed are described below: Parameter Description Device Name Display the Device Name of the switches in the SIM group configured by the user. If no Device Name is configured by the name, it will be given the name default and tagged with the last six digits of the MAC Address to identify it.
Page 85 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Member Switch Icon Figure 4-56 Right-clicking a Member icon The following options may appear for the user to configure: • Collapse - To collapse the group that will be represented by a single icon.
Page 86: Firmware Upgrade
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide File • Print Setup - Will view the image to be printed. • Print Topology - Will print the topology map. • Preference - Will set display properties, such as polling interval, and the views to open at SIM startup.
Page 87: Configuration File Backup/Restore
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 4-62 Firmware Upgrade window The fields that can be configured are described below: Parameter Description TFTP Server IP Enter the TFTP server IP address. Path\Filename Enter the path and file name.
Page 88: D-Link Discovery Protocol
D-Link Discovery Protocol This window is used to configure and display D-Link Discovery Protocol (DDP). To view the following window, click Management > D-Link Discovery Protocol, as shown below: Figure 4-65 D-Link Discovery Protocol window The fields that can be configured for D-Link Discovery Protocol are described below:...
Page 89 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description D-Link Discovery Protocol Select this option to enable or disable DDP global state. State Report Timer Select the interval in seconds between two consecutive DDP report messages. Options to choose from are 30, 60, 90,120, and Never.
Page 90: Layer 2 Features
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Layer 2 Features VLAN Spanning Tree Loopback Detection Link Aggregation L2 Multicast Control LLDP Static FDB Unicast Static FDB This window is used to view and configure the static unicast forwarding settings on the Switch.
Page 91: Mac Address Table Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Multicast Static FDB This window is used to view and configure the multicast static FDB settings. To view the following window, click L2 Features > FDB > Static FDB > Multicast Static FDB, as shown below:...
Page 92: Mac Address Table
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Aging Destination Hit Select to enable or disable the aging destination hit function. Click the Apply button to accept the changes made. After clicking the MAC Address Learning tab, at the top of the page, the following page will be available.
Page 93: Mac Notification
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-5 MAC Address Table window The fields that can be configured are described below: Parameter Description Port Select the switch unit and the port that will be used for this configuration here.
Page 94 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-6 MAC Notification (MAC Notification Settings) window The fields that can be configured are described below: Parameter Description MAC Address Notification Select to enable or disable MAC notification globally on the Switch.
Page 95: Vlan
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-7 MAC Notification (MAC Notification History) window A list of MAC notification messages will be displayed. VLAN 802.1Q VLAN This window is used to view and configure the VLAN settings on this switch.
Page 96: Gvrp
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide GVRP GVRP Global This window is used to view and configure the GARP VLAN Registration Protocol (GVRP) global settings. To view the following window, click L2 Features > VLAN > GVRP > GVRP Global, as shown below:...
Page 97 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 98 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 99: Asymmetric Vlan
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide GVRP Statistics Table This window is used to display GVRP statistics information. To view the following window, click L2 Features > VLAN > GVRP > GVRP Statistics Table, as shown...
Page 100: Vlan Interface
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Asymmetric VLAN State Select this option to enable or disable the asymmetric VLAN function Click the Apply button to accept the changes made.
Page 101 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-16 VLAN Interface Information window More detailed information about the VLAN of the specific interface is displayed. Click the Back button to return to the previous window. After click the Edit button, the following window will appear. This is a dynamic window that will change when a different VLAN Mode was selected.
Page 102 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-18 Configure VLAN Interface - Hybrid window The fields that can be configured are described below: Parameter Description VLAN Mode Select the VLAN mode option here. Options to choose from are Access, Hybrid, and Trunk.
Page 103: Auto Surveillance Vlan
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description VLAN Mode Select the VLAN mode option here. Options to choose from are Access, Hybrid, and Trunk. Acceptable Frame Select the acceptable frame behavior option here.
Page 104 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-20 Auto Surveillance Properties window The fields that can be configured for Global Settings are described below: Parameter Description Surveillance VLAN Select this option to enable or disable the surveillance VLAN state Surveillance VLAN ID Enter the surveillance VLAN ID.
Page 105 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide MAC Settings and Surveillance Device This window is used to configure the user-defined surveillance device OUI and display the surveillance VLAN information. To view the following window, click L2 Features > VLAN > Auto Surveillance VLAN > MAC Settings...
Page 106: Voice Vlan
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Voice VLAN Voice VLAN Global Voice VLAN is a VLAN used to carry voice traffic from IP phone. Because the sound quality of an IP phone call will be deteriorated if the data is unevenly sent, the quality of service (QoS) for voice traffic shall be configured to ensure the transmission priority of voice packet is higher than normal traffic.
Page 107 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-24 Voice VLAN Port window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 108 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-25 Voice VLAN OUI window The fields that can be configured are described below: Parameter Description OUI Address Enter the OUI MAC address. Mask Enter the OUI MAC address matching bitmask.
Page 109: Spanning Tree
Rapid STP, and 802.1Q-2005 MSTP. 802.1D-1998 STP will be familiar to most networking professionals. However, since 802.1D-2004 RSTP and 802.1Q-2005 MSTP have been recently introduced to D-Link managed Ethernet switches, a brief introduction to the technology is provided below followed by a description of how to set up 802.1D-1998 STP, 802.1D-2004 RSTP, and 802.1Q-2005 MSTP.
Page 110 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The Switch must be set to the MSTP setting (found in the STP Bridge Global Settings window in the STP Version field) The correct spanning tree priority for the MSTP instance must be entered (defined here as a Priority in the MSTI Config Information window when configuring MSTI ID settings).
Page 111: Stp Global Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Edge Port The edge port is a configurable designation used for a port that is directly connected to a segment where a loop cannot be created. An example would be a port connected directly to a single workstation. Ports that are designated as edge ports transition to a forwarding state immediately without going through the listening and learning states.
Page 112 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The field that can be configured for Spanning Tree State is described below: Parameter Description Spanning Tree State Select this option to enable or disable the STP global state here.
Page 113: Stp Port Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide between 4 and 30 seconds. By default, this value is 15 seconds. Any port on the Switch spends this time in the listening state while moving from the blocking state to the forwarding state.
Page 114: Mst Configuration Identification
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide of forwarding packets to the specified port list. Port cost can be set automatically or as a metric value. The default value is 0 (auto). Setting 0 for the external cost will automatically set the speed for forwarding packets to the specified port(s) in the list for optimal efficiency.
Page 115: Stp Instance
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-30 MST Configuration Identification window The fields that can be configured for MST Configuration Identification are described below: Parameter Description Configuration Name Enter the MST This name uniquely identifies the MSTI (Multiple Spanning Tree Instance).
Page 116: Mstp Port Information
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-31 STP Instance window Click the Edit button to re-configure the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 117 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide or a VLAN, this signifies a loop on the network. The Switch will automatically block the port or the VLAN and send an alert to the administrator. The Loopback Detection port will restart (change to normal state) when the Loopback Detection Recover Time times out.
Page 118: Link Aggregation
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made. Link Aggregation Understanding Port Trunk Groups Port trunk groups are used to combine a number of ports together to make a single high-bandwidth data pipeline.
Page 119 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide locking and 802.1X must not be enabled on the trunk group. Further, the LACP aggregated links must all be of the same speed and should be configured as full duplex.
Page 120: L2 Multicast Control
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 121: Igmp Snooping
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IGMP Snooping Internet Group Management Protocol (IGMP) snooping allows the Switch to recognize IGMP queries and reports sent between network stations or devices and an IGMP host. IGMP Snooping Settings In order to use IGMP Snooping it must first be enabled for the entire Switch under IGMP Global Settings at the top of the window.
Page 122 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Find All button to view all the entries. Click the Show Detail button to see the detail information of the specific VLAN. Click the Edit button to re-configure the specific entry.
Page 123 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Minimum Version Select the minimum version of IGMP hosts that is allowed on the VLAN. Fast Leave Select this option to enable or disable the IGMP snooping fast leave function.
Page 124 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-40 IGMP Snooping Groups Settings The fields that can be configured for IGMP Snooping Static Groups Settings are described below: Parameter Description Enter a VLAN ID of the multicast group.
Page 125 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click L2 Features > L2 Multicast Control > IGMP Snooping > IGMP Snooping Mrouter Settings, as shown below: Figure 5-41 IGMP Snooping Mrouter Settings window...
Page 126: Mld Snooping
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-42 IGMP Snooping Statistics Settings window The fields that can be configured for IGMP Snooping Statistics Settings are described below: Parameter Description Statistics Select the interface here. Options to choose from are All, VLAN, and Port.
Page 127 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide receive this data through the use of queries and reports produced by the requesting ports and the source of the multicast traffic. MLD snooping is accomplished through the examination of the layer 3 part of an MLD control packet transferred between end nodes and a MLD router.
Page 128 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-43 MLD Snooping Settings window The field that can be configured for Global Settings is described below: Parameter Description Global State Select this option to enable or disable MLD snooping global state.
Page 129 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-44 MLD Snooping VLAN Parameters window The window displays the detail information about MLD snooping VLAN. Click the Modify button to edit the information in the following window. After clicking the Edit button in MLD Snooping Settings window, the following window will appear.
Page 130 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Report Suppression Select this option to enable or disable the report suppression. Suppression Time Enter the interval of suppressing duplicate MLD reports or leaves. The range is from 1 to 300.
Page 131 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Group Address Enter an IPv6 multicast group address. Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 132 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port - Select to have the configured ports as being connected to multicast-enabled routers. Forbidden Port - Select to have the configured ports as being not connected to multicast-enabled routers.
Page 133: Multicast Filtering
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Unit Select the switch unit that will be used for this configuration here. This is available when Port is selected in the Statistics drop-down list. From Port / To Port Select the appropriate port range used for the configuration here.
Page 134: Lldp
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide the forwarding table and all unregistered multicast packets will be filtered. Click the Apply button to accept the changes made. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 135: Lldp Port Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide LLDP State is disabled and LLDP Forward Sate is enabled, the received LLDPDU packet will be forwarded. LLDP Trap State Select this option to enable or disable the LLDP trap state.
Page 136 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-51 LLDP Port Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 137: Lldp Management Address List
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide LLDP Management Address List This window is used to view the LLDP management address list. To view the following window, click L2 Features > LLDP > LLDP Management Address List, as shown...
Page 138: Lldp Dot1 Tlvs Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-53 LLDP Basic TLVs Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 139: Lldp Dot3 Tlvs Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-54 LLDP Dot1 TLVs Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 140: Lldp-Med Port Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-55 LLDP Dot3 TLVs Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 141: Lldp Statistics Information
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-56 LLDP-MED Port Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 142: Lldp Local Port Information
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-57 LLDP Statistics Information window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be displayed. Port Select the port number that will be displayed.
Page 143 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-58 LLDP Local Port Information window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be displayed. Port Select the port number that will be displayed.
Page 144: Lldp Neighbor Port Information
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 5-60 LLDP Local Port Information - Show Detail window LLDP Neighbor Port Information This window is used to display the information learned from the neighbors. The switch receives packets from a remote station but is able to store the information as local.
Page 145: Layer 3 Features
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Layer 3 Features Gratuitous ARP IPv4 Interface IPv4 Static/Default Route IPv4 Route Table IPv6 Interface IPv6 Neighbor IPv6 Static/Default Route IPv6 Route Table ARP Aging Time This window is used to view and configure the ARP aging time settings.
Page 146: Proxy Arp
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 6-2 Static ARP window The fields that can be configured are described below: Parameter Description IP Address Enter the IP address that will be associated with the MAC address here.
Page 147: Arp Table
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Edit button to re-configure the specific entry. ARP Table This window is used to view and configure the ARP table settings. To view the following window, click L3 Features > ARP > ARP Table, as shown below:...
Page 148: Ipv4 Interface
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 6-5 Gratuitous ARP window The fields that can be configured are described below: Parameter Description IP Gratuitous ARP State Select this option to enable or disable the learning of gratuitous ARP packets in the ARP cache table.
Page 149 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Interface VLAN Enter the interface’s VLAN ID here. This value must be between 1 and 4094. Click the Apply button to accept the changes made.
Page 150: Ipv4 Static/Default Route
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Mask Enter the IPv6 subnet mask for this interface here. Secondary Tick the check box to use the IPv4 address and mask as the secondary interface configuration. Click the Apply button to accept the changes made.
Page 151: Ipv4 Route Table
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click L3 Features > IPv4 Static/Default Route, as shown below: Figure 6-9 IPv4 Static/Default Route window The fields that can be configured are described below:...
Page 152: Ipv6 Interface
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description IP Address Select and enter the single IPv4 address here. Network Address Select and enter the IPv4 network address here. In the first space enter the network prefix and in the second space enter the network mask.
Page 153 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 6-12 IPv6 Interface - Detail, IPv6 Interface Settings window The fields that can be configured for Interface are described below: Parameter Description IPv6 State Select to enable or disable the IPv6 interface’s global state here.
Page 154: Ipv6 Neighbor
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 6-14 IPv6 Interface - Detail, Interface IPv6 Address window Click the Restart button to restart DHCPv6 client on an interface. The fields that can be configured for DHCPv6 Client Settings are described below:...
Page 155: Ipv6 Static/Default Route
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete button to remove the specific entry. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. IPv6 Static/Default Route This window is used to view and configure the IPv6 static or default routes.
Page 156 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 6-17 IPv6 Route Table window The fields that can be configured are described below: Parameter Description IPv6 Address Select and enter the IPv6 address to display here. IPv6 Address/Prefix Length Select and enter the IPv6 address and prefix length to display here.
Page 157: Quality Of Service (Qos)
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Quality of Service (QoS) Basic Settings Advanced Settings Basic Settings Port Default CoS This window is used to view and configure the port’s default CoS settings. To view the following window, click QoS > Basic Settings > Port Default CoS, as shown below:...
Page 158 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click QoS > Basic Settings > Port Scheduler Method, as shown below: Figure 7-2 Port Scheduler Method window The fields that can be configured are described below:...
Page 159: Queue Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide weight is replenished. When weights of all CoS queues reach 0, the weights get replenished at a time. Click the Apply button to accept the changes made. Queue Settings This window is used to view and configure the queue settings.
Page 160: Cos To Queue Mapping
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide and 127. Click the Apply button to accept the changes made. CoS to Queue Mapping This window is used to view and configure the CoS-to-Queue mapping settings. To view the following window, click QoS > Basic Settings > CoS to Queue Mapping, as shown below:...
Page 161: Queue Rate Limiting
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 7-5 Port Rate Limiting window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 162 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click QoS > Basic Settings > Queue Rate Limiting, as shown below: Figure 7-6 Queue Rate Limiting window The fields that can be configured are described below:...
Page 163: Advanced Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide When the Min Percent option is selected, enter the minimum bandwidth percentage value in the space provided. This value must be between 1 and 100 percent (%). Also enter the maximum percentage value (Max Percent) in the space provided.
Page 164: Port Trust State And Mutation Binding
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Trust State and Mutation Binding This window is used to view and configure port trust state and mutation binding settings. To view the following window, click QoS > Advanced Settings > Port Trust State and Mutation...
Page 165: Cos Color Mapping
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 7-9 DSCP CoS Mapping window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 166: Dscp Color Mapping
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 7-10 CoS Color Mapping window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 167: Class Map
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 7-11 DSCP Color Mapping window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 168 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 7-12 Class Map window The fields that can be configured are described below: Parameter Description Class Map Name Enter the class map name here. This name can be up to 32 characters long.
Page 169: Aggregate Policer
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide SSH, Telnet, and TFTP. VID List Select and enter the VLAN list value that will be matched with the class map here. This value must be between 1 and 4094.
Page 170 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Exceed Action Select the exceed action here. The exceed action specifies the action to take on packets that exceed the rate limit. For a two rate policer, if the exceed action is not specified, the default action is Drop. Options to choose from are Drop, Set-DSCP-Transmit, Set-1P-Transmit, Transmit, and Set-DSCP-1P.
Page 171 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After clicking the Two Rate Setting tab, at the top of the page, the following page will be available. Figure 7-15 Two Rate Settings window The fields that can be configured are described below:...
Page 172: Policy Map
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide value in the space provided. This value sets the IP differentiated services code point (DSCP) value and transmits the packet with the new IP DSCP value. When selecting the Set-1P-Transmit option, enter the 1P transmit value in the space provided.
Page 173 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 7-16 Policy Map window The fields that can be configured for Create/Delete Policy Map are described below: Parameter Description Policy Map Name Enter the policy map’s name here that will be created or deleted. This name can be up to 32 characters long.
Page 174 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 7-17 Policy Map (View Rules) window Click the Set Action button to configure the action for the policy map. Click the Policer button to configure the policer action for the policy map.
Page 175: Policy Binding
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide and 7. This overwrites the original CoS queue selection. Click the Apply button to accept the changes made. Click the Back button to return to the previous window. After clicking the Policer button, the following window will appear.
Page 176 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click QoS > Advanced Settings > Policy Binding, as shown below: Figure 7-20 Policy Binding window The fields that can be configured are described below:...
Page 177: Access Control List (Acl)
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Access Control List (ACL) ACL Configuration Wizard ACL Access List ACL Interface Access Group ACL VLAN Access Map ACL VLAN Filter ACL Configuration Wizard This window is used to guide the user to create a new ACL access list or configure an existing ACL access list.
Page 178 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. After clicking the Next button, the following window will appear. Figure 8-3 ACL Configuration Wizard (Select Packet Type) window...
Page 179 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-4 ACL Configuration Wizard (Add Rule for MAC ACL) window The fields that can be configured are described below: Parameter Description Sequence No. Enter the ACL rule number here. This value must be between 1 and 65535.
Page 180 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide hexadecimal value will automatically be entered. Ethernet Type Mask Enter the Ethernet type mask hexadecimal value here. This value must be between 0x0 and 0xFFFF. When any Ethernet type profile is selected in the Specify Ethernet Type drop-down list, the appropriate hexadecimal value will automatically be entered.
Page 181 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-6 ACL Configuration Wizard (Add Rule for IPv4 ACL) TCP window The dynamic fields that can be configured are described below: Parameter Description Source Select and enter the source information here. Options to choose from are Any, Host, and IP.
Page 182 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide port number(s) is/are not available in the drop-down list. Destination Port Select and enter the destination port value here. Options to choose from are =, >, <, ≠, and Range. When selecting the = option, the specific selected port number will be used.
Page 183 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the UDP option as the Protocol Type, the following section will appear. Figure 8-7 ACL Configuration Wizard (Add Rule for IPv4 ACL) UDP window The dynamic fields that can be configured are described below:...
Page 184 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide used. When selecting the Range option, the start port number and end port number selected, of the range, will be used. Alternatively, the port number(s) can manually be entered in the space(s) provided, if the port number(s) is/are not available in the drop-down list.
Page 185 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ICMP option as the Protocol Type, the following section will appear. Figure 8-8 ACL Configuration Wizard (Add Rule for IPv4 ACL) ICMP window The dynamic fields that can be configured are described below:...
Page 186 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IP Precedence Select the IP precedence value used here. Options to choose from are 0 (routine), 1 (priority), 2, (immediate), 3 (flash), 4 (flash-override), 5 (critical), 6 (internet), and 7 (network).
Page 187 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide from are Any, Host, and IP. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s IP address here.
Page 188 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide the Host option is selected, enter the source host’s IP address here. When the IP option is selected, the Wildcard option will also be available. Enter the group of source IP addresses by using a wildcard bitmap.
Page 189 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Fragments Select the Fragments option to include packet fragment filtering. Source Select and enter the source information here. Options to choose from are Any, Host, and IP. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule.
Page 190 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the IGMP option as the Protocol Type, the following section will appear. Figure 8-12 ACL Configuration Wizard (Add Rule for IPv4 ACL) IGMP window The dynamic fields that can be configured are described below:...
Page 191 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide between 0 and 63. Time Range Enter the name of the time range to associate with this ACL rule. Action Select the action that this rule will take here. Options to choose from are Permit and Deny.
Page 192 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 5 (critical), 6 (internet), and 7 (network). After selecting the IP precedence value, select the Type-of-Service (ToS) value that will be used here. Options to choose from are 0 (normal), 1 (min-monetary-cost), 2 (max-reliability), 3, 4 (max- throughput), 5, 6, 7, 8 (min-delay), 9, 10, 11, 12, 13, 14, and 15.
Page 193 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide address here. When the IP option is selected, the Wildcard option will also be available. Enter the group of destination IP addresses by using a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored.
Page 194 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. Destination Select and enter the destination information here. Options to choose from are Any, Host, and IP.
Page 195 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The dynamic fields that can be configured are described below: Parameter Description Fragments Select the Fragments option to include packet fragment filtering. Source Select and enter the source information here. Options to choose from are Any, Host, and IP.
Page 196 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the PCP option as the Protocol Type, the following section will appear. Figure 8-17 ACL Configuration Wizard (Add Rule for IPv4 ACL) PCP window The dynamic fields that can be configured are described below:...
Page 197 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide between 0 and 63. Time Range Enter the name of the time range to associate with this ACL rule. Action Select the action that this rule will take here. Options to choose from are Permit and Deny.
Page 198 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IP Precedence Select the IP precedence value used here. Options to choose from are 0 (routine), 1 (priority), 2, (immediate), 3 (flash), 4 (flash-override), 5 (critical), 6 (internet), and 7 (network).
Page 199 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide from are Any, Host, and IP. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s IP address here.
Page 200 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide UDP, ICMP, Protocol ID, ESP, PCP, SCTP, and None. After selecting the TCP option as the Protocol Type, the following section will appear. Figure 8-21 ACL Configuration Wizard (Add Rule for IPv6 ACL) TCP window...
Page 201 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide selecting the ≠ option, all ports, excluding the selected port, will be used. When selecting the Range option, the start port number and end port number selected, of the range, will be used. Alternatively, the port number(s) can manually be entered in the space(s) provided, if the port number(s) is/are not available in the drop-down list.
Page 202 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the UDP option as the Protocol Type, the following section will appear. Figure 8-22 ACL Configuration Wizard (Add Rule for IPv6 ACL) UDP window The dynamic fields that can be configured are described below:...
Page 203 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide number(s) can manually be entered in the space(s) provided, if the port number(s) is/are not available in the drop-down list. Destination Port Select and enter the destination port value here. Options to choose from are =, >, <, ≠, and Range.
Page 204 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Source Select and enter the source information here. Options to choose from are Any, Host, and IPv6. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IPv6 address here.
Page 205 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the Protocol ID option as the Protocol Type, the following section will appear. Figure 8-24 ACL Configuration Wizard (Add Rule for IPv6 ACL) Protocol ID window The dynamic fields that can be configured are described below:...
Page 206 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide are Permit and Deny. After selecting the ESP option as the Protocol Type, the following section will appear. Figure 8-25 ACL Configuration Wizard (Add Rule for IPv6 ACL) ESP window...
Page 207 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Action Select the action that this rule will take here. Options to choose from are Permit and Deny. After selecting the PCP option as the Protocol Type, the following section will appear.
Page 208 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Time Range Enter the name of the time range to associate with this ACL rule. Action Select the action that this rule will take here. Options to choose from are Permit and Deny.
Page 209 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 1048575. Time Range Enter the name of the time range to associate with this ACL rule. Action Select the action that this rule will take here. Options to choose from are Permit and Deny.
Page 210: Acl Access List
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Flow Label Enter the flow label value here. This value must be between 0 and 1048575. Time Range Enter the name of the time range to associate with this ACL rule.
Page 211: Standard Ip Acl
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description ACL Type Select the ACL profile type to find here. Options to choose from are All, IP ACL, IPv6 ACL, MAC ACL, and Expert ACL. Enter the ACL ID here. The range is from 1 to 14999.
Page 212 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-32 Standard IP ACL (Main) window Click the Edit button to re-configure the specific ACL profile. Click the Delete button to remove the specific ACL profile. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist.
Page 213 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Sequence No. Enter the ACL rule number here. This value must be between 1 and 65535. If this value is not specified, the system will automatically generate an ACL rule number for this entry.
Page 214: Extended Ip Acl
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Remark Enter an optional remark that will be associated with this profile here. Click the Apply button to accept the changes made. Click the Delete button to remove the specific entry.
Page 215 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide characters long. Click the Apply button to create the new ACL profile. After creating an Extend IP ACL profile, the newly created Extend IP ACL profile will be displayed in the...
Page 216 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-40 Extended IP ACL (Add Rule) window This is a dynamic page. Every selection made in the Protocol Type drop-down list will change the bottom part of this window.
Page 217 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-41 Extended IP ACL (Add Rule) TCP window The dynamic fields that can be configured are described below: Parameter Description Source Select and enter the source information here. Options to choose from are Any, Host, and IP.
Page 218 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Destination Port Select and enter the destination port value here. Options to choose from are =, >, <, ≠, and Range. When selecting the = option, the specific selected port number will be used. When selecting the >...
Page 219 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Source Select and enter the source information here. Options to choose from are Any, Host, and IP. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IP address here.
Page 220 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the ICMP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-43 Extended IP ACL (Add Rule) ICMP window The dynamic fields that can be configured are described below:...
Page 221 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide automatically be entered. IP Precedence Select the IP precedence value used here. Options to choose from are 0 (routine), 1 (priority), 2, (immediate), 3 (flash), 4 (flash-override), 5 (critical), 6 (internet), and 7 (network).
Page 222 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. IP Precedence Select the IP precedence value used here. Options to choose from are 0 (routine), 1 (priority), 2, (immediate), 3 (flash), 4 (flash-override), 5 (critical), 6 (internet), and 7 (network).
Page 223 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide also be available. Enter the group of destination IP addresses by using a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked.
Page 224 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide address here. When the IP option is selected, the Wildcard option will also be available. Enter the group of destination IP addresses by using a wildcard bitmap. The bit corresponding to the bit value 1 will be ignored.
Page 225 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide rule. When the Host option is selected, enter the destination host’s IP address here. When the IP option is selected, the Wildcard option will also be available. Enter the group of destination IP addresses by using a wildcard bitmap.
Page 226 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s IP address here. When the IP option is selected, the Wildcard option will also be available.
Page 227 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide from are Any, Host, and IP. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s IP address here.
Page 228 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Destination Select and enter the destination information here. Options to choose from are Any, Host, and IP. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule.
Page 229 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide corresponding to the bit value 0 will be checked. Destination Select and enter the destination information here. Options to choose from are Any, Host, and IP. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule.
Page 230 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide bitmap. The bit corresponding to the bit value 1 will be ignored. The bit corresponding to the bit value 0 will be checked. Destination Select and enter the destination information here. Options to choose from are Any, Host, and IP.
Page 231 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide the Host option is selected, enter the source host’s IP address here. When the IP option is selected, the Wildcard option will also be available. Enter the group of source IP addresses by using a wildcard bitmap.
Page 232 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IP address here. When the IP option is selected, the Wildcard option will also be available.
Page 233: Standard Ipv6 Acl
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Remark Enter an optional remark that will be associated with this profile here. Click the Apply button to accept the changes made. Click the Delete button to remove the specific entry.
Page 234 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ACL Name Enter the ACL profile’s name here. This name can be up to 32 characters long. Click the Apply button to create the new ACL profile. After creating a Standard IPv6 ACL profile, the newly created Standard IPv6 ACL profile will be displayed...
Page 235 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-60 Standard IPv6 ACL (Add Rule) window The fields that can be configured are described below: Parameter Description Rule Number Enter the ACL rule number here. This value must be between 1 and 65535.
Page 236 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-61 Standard IPv6 ACL (Edit ACL) window The fields that can be configured are described below: Parameter Description Start Sequence No. Enter the start sequence number here. Step Enter the sequence number increment here.
Page 237: Extended Ipv6 Acl
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Extended IPv6 ACL After clicking the Add ACL button, users can create a new ACL profile, as shown below: Figure 8-63 Extended IPv6 ACL (Add Profile) window The fields that can be configured are described below:...
Page 238 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To add an ACL rule in the ACL profile, select it (the ACL profile will toggle to the bold font), and click the Add Rule button. Figure 8-65 Extended IPv6 ACL (Selected) window...
Page 239 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Sequence No. Enter the ACL rule number here. This value must be between 1 and 65535. If this value is not specified, the system will automatically generate an ACL rule number for this entry.
Page 240 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Source Port Select and enter the source port value here. Options to choose from are =, >, <, ≠, and Range. When selecting the = option, the specific selected port number will be used. When selecting the > option, all ports greater than the selected port, will be used.
Page 241 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the UDP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-68 Extended IPv6 ACL (Add Rule) UDP window The dynamic fields that can be configured are described below:...
Page 242 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide from are =, >, <, ≠, and Range. When selecting the = option, the specific selected port number will be used. When selecting the > option, all ports greater than the selected port, will be used. When selecting the <...
Page 243 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s IPv6 address here. When the IPv6 option is selected, the Prefix Length option will also be available.
Page 244 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide are Any, Host, and IPv6. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IPv6 address here.
Page 245 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Destination Select and enter the destination information here. Options to choose from are Any, Host, and IPv6th. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule.
Page 246 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide address and prefix length value in the spaces provided. DSCP Select or enter the DSCP value used here. This value must be between 0 and 63. Flow Label Enter the flow label value here. This value must be between 0 and 1048575.
Page 247 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Time Range Enter the name of the time range to associate with this ACL rule. After selecting the None option as the Protocol Type, the following page and parameters will be...
Page 248 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To enable the Counter State option or to enter a Remark for the profile, click the Edit button, next to the specific ACL profile (found in the ACL profile table).
Page 249: Extended Mac Acl
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete button to remove the specific ACL rule. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. Extended MAC ACL...
Page 250 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete button to remove the specific ACL profile. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. To add an ACL rule in the ACL profile, select it (the ACL profile will toggle to the bold font), and click the Add Rule button.
Page 251 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide generate an ACL rule number for this entry. Action Select the action that this rule will take here. Options to choose from are Permit and Deny. Source Select and enter the source information here. Options to choose from are Any, Host, and MAC.
Page 252 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-81 Extended MAC ACL (Edit ACL) window The fields that can be configured are described below: Parameter Description Start Sequence No. Enter the start sequence number here. Stop Enter the stop sequence number here.
Page 253: Extended Expert Acl
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete button to remove the specific ACL rule. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. Extended Expert ACL...
Page 254 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete button to remove the specific ACL profile. Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. To add an ACL rule in the ACL profile, select it (the ACL profile will toggle to the bold font), and click the Add Rule button.
Page 255 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide This is a dynamic page. Every selection made in the Protocol Type option will change the bottom part of this window. The fixed fields that can be configured are described below:...
Page 256 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide are Any, Host, and IP. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IP address here.
Page 257 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DSCP Select or enter the DSCP value used here. This value must be between 0 and 63. TCP Flag Tick the appropriate TCP flag option to include the flag in this rule.
Page 258 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Destination IP Address Select and enter the destination information here. Options to choose from are Any, Host, and IP. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule.
Page 259 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Time Range Enter the name of the time range to associate with this ACL rule. After selecting the ICMP option as the Protocol Type, the following page and parameters will be...
Page 260 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide address here. When the MAC option is selected, the Wildcard option will also be available. Enter the source MAC address and wildcard value in the spaces provided. Destination MAC Address Select and enter the destination information here.
Page 261 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the EIGRP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-90 Extended Expert ACL (Add Rule) EIGRP window The dynamic fields that can be configured are described below:...
Page 262 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide from are Any, Host, and MAC. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s MAC address here.
Page 263 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Source IP Address Select and enter the source information here. Options to choose from are Any, Host, and IP. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IP address here.
Page 264 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the GRE option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-92 Extended Expert ACL (Add Rule) GRE window The dynamic fields that can be configured are described below:...
Page 265 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide from are Any, Host, and MAC. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s MAC address here.
Page 266 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Source IP Address Select and enter the source information here. Options to choose from are Any, Host, and IP. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IP address here.
Page 267 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the OSPF option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-94 Extended Expert ACL (Add Rule) OSPF window The dynamic fields that can be configured are described below:...
Page 268 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide from are Any, Host, and MAC. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s MAC address here.
Page 269 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Source IP Address Select and enter the source information here. Options to choose from are Any, Host, and IP. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IP address here.
Page 270 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the VRRP option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-96 Extended Expert ACL (Add Rule) VRRP window The dynamic fields that can be configured are described below:...
Page 271 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s MAC address here. When the MAC option is selected, the Wildcard option will also be available.
Page 272 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide are Any, Host, and IP. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IP address here.
Page 273 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-98 Extended Expert ACL (Add Rule) PCP window The dynamic fields that can be configured are described below: Parameter Description Fragments Select the Fragments option to include packet fragment filtering.
Page 274 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide MAC address here. When the MAC option is selected, the Wildcard option will also be available. Enter the destination MAC address and wildcard value in the spaces provided. IP Precedence Select the IP precedence value used here.
Page 275 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Source IP Address Select and enter the source information here. Options to choose from are Any, Host, and IP. When the Any option is selected, any source traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the source host’s IP address here.
Page 276 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide After selecting the None option as the Protocol Type, the following page and parameters will be available, as shown below: Figure 8-100 Extended Expert ACL (Add Rule) None window The dynamic fields that can be configured are described below:...
Page 277 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide from are Any, Host, and MAC. When the Any option is selected, any destination traffic will be evaluated according to the conditions of this rule. When the Host option is selected, enter the destination host’s MAC address here.
Page 278: Acl Interface Access Group
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Remark Enter an optional remark that will be associated with this profile here. Click the Apply button to accept the changes made. Click the Delete button to remove the specific entry.
Page 279: Acl Vlan Access Map
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-103 ACL Interface Access Group window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 280 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-104 ACL VLAN Access Map window The fields that can be configured are described below: Parameter Description Access Map Name Enter the access map’s name here. This name can be up to 32 characters long.
Page 281: Acl Vlan Filter
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 8-105 Match Access-List window The fields that can be configured are described below: Parameter Description Match IP Access-List Select the standard or extended IP ACL. Match IPv6 Access-List Select the standard or extended IPv6 ACL.
Page 282 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Action Select the action that will be taken here. Options to choose from are Add and Delete. VID List Enter the VLAN ID list that will be used here. Select the All VLANs option to apply this configuration to all the VLANs configured on this switch.
Page 283: Security
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Security Port Security 802.1X RADIUS TACACS IMPB DHCP Server Screening ARP Spoofing Prevention BPDU Attack Protection MAC Authentication Web-based Access Control Japanese Web-based Access Control Network Access Authentication Safeguard Engine...
Page 284: Port Security Port Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Trap Rate Enter the number of traps per second. The range is from 0 to 1000. The default value 0 indicates an SNMP trap to be generated for every security violation.
Page 285: Port Security Address Entries
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide from are Protect, Restrict, and Shutdown. Selecting Protect specifies to drop all packets from the insecure hosts at the port- security process level, but does not increment the security-violation count. Selecting Restrict specifies to drop all packets from the insecure hosts at the port-security process level and increments the security-violation count and record the system log.
Page 286: 278
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Add button to add a new entry based on the information entered. Click the Delete button to remove a new entry based on the information entered. Click the Clear by Port button to clear the information based on the port selected.
Page 287 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Authentication Server The Authentication Server is a remote device that is connected to the same network as the Client and Authenticator, must be running a RADIUS Server program and must be configured properly on the Authenticator (Switch).
Page 288 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Three steps must be implemented on the Switch to properly configure the Authenticator. • The 802.1X State must be Enabled. (Security > 802.1X > 802.1X Global Settings) • The 802.1X settings must be implemented by port (Security > 802.1X > 802.1X Port Settings) •...
Page 289 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-9 The 802.1X Authentication Process The D-Link implementation of 802.1X allows network administrators to choose between two types of Access Control used on the Switch, which are: • Port-based Access Control – This method requires only one user to be authenticated per port by a remote RADIUS server to allow the remaining users on the same port access to the network.
Page 290 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-10 Example of Typical Port-based Configuration Host-based Network Access Control In order to successfully make use of 802.1X in a shared media LAN segment, it would be necessary to create “logical”...
Page 291: 802.1X Global Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 802.1X Global Settings This window is used to view and configure the 802.1X global settings. To view the following window, click Security > 802.1X > 802.1X Global Settings, as shown below: Figure 9-12 802.1X Global Settings window...
Page 292 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-13 802.1X Port Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 293: Authentication Session Information
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide (PAE) authenticator. Server Timeout Enter the server timeout value here. This value must be between 1 and 65535 seconds. By default, this value is 30 seconds. Supp Timeout Enter the supplicant timeout value here. This value must be between 1 and 65535 seconds.
Page 294: Authenticator Session Statistics
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this query here. Port Select the appropriate port used for the query here.
Page 295: Aaa
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-17 Authenticator Diagnostics window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this query here. Port Select the appropriate port used for the query here.
Page 296: Application Accounting Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Login Method List After clicking the Edit button for the specific entry, enter the login method list name used here.
Page 297: Authentication Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Authentication Settings This window is used to view and configure the AAA network and EXEC authentication settings. To view the following window, click Security > AAA > Authentication Settings, as shown below: Figure 9-21 Authentication Settings window The fields that can be configured for AAA Authentication 802.1X are described below:...
Page 298 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for AAA Authentication WEB-Auth are described below: Parameter Description Status Select to enable or disable the AAA Web authentication state here. Method 1 to 4 Select the method lists that will be used for this configuration here.
Page 299: Accounting Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Accounting Settings This window is used to view and configure the AAA accounting settings. To view the following window, click Security > AAA > Accounting Settings, as shown below: Figure 9-23 Accounting Settings window...
Page 300: Radius
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-25 AAA Accounting Exec window The fields that can be configured are described below: Parameter Description List Name Enter the method list name that will be used with the AAA accounting EXEC option here.
Page 301: Radius Server Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-27 RADIUS Global Settings window The fields that can be configured are described below: Parameter Description Dead Time Enter the dead time value here. This value must be between 1 and 1440 minutes.
Page 302: Radius Group Server Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide and 20. By default, this value is 3. To disable this option, enter the value 0. Timeout Enter the timeout value used here. This value must be between 1 and 255 seconds.
Page 303: Radius Statistic
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-30 RADIUS Group Server Settings - Detail window Click the Delete button to remove the specified entry. Click the Back button to return to the previous window. RADIUS Statistic This window is used to view and clear the RADIUS statistics information.
Page 304: Tacacs
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide TACACS TACACS Server Settings This window is used to view and configure the TACACS server settings. To view the following window, click Security > TACACS > TACACS Server Settings, as shown below:...
Page 305: Tacacs Statistic
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-33 TACACS Group Server Settings window The fields that can be configured are described below: Parameter Description Group Server Name Enter the TACACS group server’s name here. This name can be up to 15 characters long.
Page 306: Impb
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-35 TACACS Statistic window The fields that can be configured are described below: Parameter Description Group Server Name Select the TACACS group server name from this list here. Click the Clear by Group button to clear the information based on the group selected.
Page 307 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide When DHCP snooping station move is enabled, the dynamic DHCP snooping binding entry with the same VLAN ID and MAC address on the specific port can move to another port if it detects that a new DHCP process belong to the same VLAN ID and MAC address.
Page 308 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trusted Select the trusted option here. Options to choose from are No and Yes. Ports connected to the DHCP server or to other switches should be configured as trusted interfaces. The ports connected to DHCP clients should be configured as untrusted interfaces.
Page 309 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-39 DHCP Snooping Database window The fields that can be configured for DHCP Snooping Database are described below: Parameter Description Write Delay Enter the write delay time value here. This value must be between 60 and 86400 seconds.
Page 310 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click Security > IMPB > IPv4 > DHCPv4 Snooping > DHCP Snooping Binding Entry, as shown below: Figure 9-40 DHCP Snooping Binding Entry window The fields that can be configured are described below:...
Page 311 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-41 ARP Access List window The fields that can be configured are described below: Parameter Description ARP Access List Name Enter the ARP access list name used here. This name can be up to 32 characters long.
Page 312 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide ARP Inspection Settings This window is used to view and configure the ARP inspection settings. To view the following window, click Security > IMPB > IPv4 > Dynamic ARP Inspection > ARP...
Page 313 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Static ACL Select whether to use a static ACL or not here by either selecting Yes or No. Click the Add button to add a new entry based on the information entered.
Page 314 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 15. Tick the None option to disable the option. Trust State Select to enable or disable the trust state here. Click the Apply button to accept the changes made. Click the Set to Default button to change the information to the default values.
Page 315 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Enter a page number and click the Go button to navigate to a specific page when multiple pages exist. ARP Inspection Log This window is used to view, configure and clear the ARP inspection log information.
Page 316 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide port(s) here. Validation Select the validation method used here. Options to choose from are IP and IP-MAC. Selecting IP means that the IP address of the received packets will be checked. Selecting IP-MAC means that the IP address and the MAC address of the received packets will be checked.
Page 317 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IP Address Enter the IP address of the binding entry here. MAC Address Enter the MAC address of the binding entry here. Enter the VLAN ID of the binding entry here.
Page 318 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-51 IP-MAC-Port Binding Settings window The fields that can be configured for IP-MAC-Port Binding Trap Settings are described below: Parameter Description Trap State Select the enable or disable the IP-MAC-Port binding option’s trap state.
Page 319: Ipv6
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide source IP address, source MAC address, VLAN ID, and arrival port must match any of the entries defined by either the IP source guard static binding entry or the DHCP snooping learned dynamic binding entry.
Page 320 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-53 IPv6 Snooping window The fields that can be configured for Station Move Setting are described below: Parameter Description Station Move Select the station move options here. Options to choose from are Permit and Deny.
Page 321 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-54 IPv6 ND Inspection window The fields that can be configured are described below: Parameter Description Policy Name Enter the policy name used here. This name can be up to 32 characters long.
Page 322 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-55 IPv6 RA Guard window The fields that can be configured are described below: Parameter Description Policy Name Enter the policy name here. This name can be up to 32 characters long.
Page 323 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Target Port Tick this option to specify the target port. Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 324 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide IPv6 Neighbor Binding This window is used to view and configure the IPv6 neighbor binding settings. To view the following window, click Security > IMPB > IPv6 > IPv6 Source Guard > IPv6 Neighbor...
Page 325: Dhcp Server Screening
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DHCP Server Screening This function allows users to not only to restrict all DHCP server packets but also to receive any specified DHCP server packet by any specified DHCP client. It is useful when one or more DHCP servers are present on the network and both provide DHCP services to different distinct groups of clients.
Page 326: Dhcp Server Screening Port Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete Profile button to remove the specified profile. The fields that can be configured for Log Information are described below: Parameter Description Log Buffer Entries Enter the logged buffer entries value here. This value must be between 10 and 1024.
Page 327: Arp Spoofing Prevention
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide State Select to enable or disable the DHCP server screening function on the port(s) specified. Server IP Enter the DHCP server’s IP address here. Profile Name Enter the DHCP server screening profile that will be used for the port(s) specified here.
Page 328 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The under attack state have three modes: drop, block, and shutdown. A BPDU protection enabled port will enter an under attack state when it receives one STP BPDU packet and it will take action based on the configuration.
Page 329: Mac Authentication
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Shutdown – Shut down the port when the port enters under attack state. Click the Apply button to accept the changes made. MAC Authentication This window is used to view and configure the MAC authentication settings. MAC authentication is a feature designed to authenticate a user by MAC address when the user is trying to access the network via the Switch.
Page 330: Web-Based Access Control
RADIUS server. The client user initiates the authentication process of WAC by attempting to gain Web access. D-Link’s implementation of WAC uses a virtual IP that is exclusively used by the WAC function and is not known by any other modules of the Switch. In fact, to avoid affecting a Switch’s other features, WAC will only use a virtual IP address to communicate with hosts.
Page 331 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide WAC pages through the Switch’s system IP. When a virtual IP is not specified, the authenticating Web request will be redirected to the Switch’s system IP. The Switch’s implementation of WAC features a user-defined port number that allows the configuration of the TCP port for either the HTTP or HTTPS protocols.
Page 332 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-64 RADIUS Authentication Server Conditions and Limitations • If the client is utilizing DHCP to attain an IP address, the authenticating VLAN must provide a DHCP server or a DHCP relay function so that client may obtain an IP address.
Page 333: Web Authentication
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide • Certain functions exist on the Switch that will filter HTTP packets, such as the Access Profile function. The user needs to be very careful when setting filter functions for the target VLAN, so that these HTTP packets are not denied by the Switch.
Page 334: Wac Port Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide WAC Port Settings This window is used to view and configure the WAC port settings. To view the following window, click Security > Web-based Access Control > WAC Port Settings, as...
Page 335: Japanese Web-Based Access Control
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-67 WAC Customize Page window The fields that can be configured are described below: Parameter Description Page Title Enter a custom page title message here. This message can be up to 128 characters long.
Page 336 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-68 JWAC Global Settings window The fields that can be configured for JWAC Global Settings are described below: Parameter Description JWAC State Select to enable or disable the JWAC feature’s global state here.
Page 337 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Virtual URL After selecting URL as the Virtual IP, the following field will be available. Enter the virtual URL used here. Forcible Logout Select to enable or disable the forcible logout option here. When the...
Page 338: Jwac Port Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Enter the update server’s port used here. This value must be between 1 and 65535. Also select whether this port is a TCP or UDP port. Click the Apply button to accept the changes made.
Page 339: Jwac Customize Page Language
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide JWAC Customize Page Language This window is used to view and configure the JWAC customize page’s language. To view the following window, click Security > Japanese Web-based Access Control > JWAC...
Page 340: Network Access Authentication
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Page Title Enter a custom page title message here. This message can be up to 128 characters long. Login window Title Enter a custom login window title here. This title can be up to 64 characters long.
Page 341: Network Access Authentication Global Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click Security > Network Access Authentication > Guest VLAN, as shown below: Figure 9-73 Guest VLAN window The fields that can be configured are described below:...
Page 342 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Network Access Authentication MAC Format Settings are described below: Parameter Description Case Select the case format that will be used for the network access authentication MAC address here.
Page 343: Network Access Authentication Port Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide User Name Enter the user name used here. This name can be up to 32 characters long. Enter the VLAN ID used here. Password Type Select the password type option here. Options to choose from are Plain Text and Encrypted.
Page 344: Network Access Authentication Sessions Information
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Host Mode Select the host mode option that will be associated with the selected port(s) here. Options to choose from are Multi Host and Multi Auth. If the port is operated in the multi-host mode, and if one of the hosts is authenticated, then all other hosts are allowed to access the port.
Page 345: Safeguard Engine
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-76 Network Access Authentication Sessions Information window The fields that can be configured are described below: Parameter Description Port Select the appropriate switch unit and port used for the query here.
Page 346: Safeguard Engine Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide packets are destined to any router or system network management interface by means of interactive access protocols, like Telnet and SSH. In the Route group, packets are identified as traversing routing packets that is generally processed by the router CPU.
Page 347: Cpu Protect Counters
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-77 Safeguard Engine Settings window The fields that can be configured for Safeguard Engine Settings are described below: Parameter Description Safeguard Engine State Select to enable or disable the safeguard engine feature here.
Page 348: Cpu Protect Sub-Interface
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide CPU protect related counters of sub-interfaces. Protocol Name Select the protocol name option here. Options to choose from are DHCP, ARP, DNS, GVRP, ICMPv4, ICMPv6-Neighbor, ICMPv6-Other, IGMP, LACP, SNMP, SSH, STP, Telnet, TFTP, Web, 802.1X, and All.
Page 349: Trusted Host
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-80 CPU Protect Type window The fields that can be configured for CPU Protect Type are described below: Parameter Description Protocol Name Select the protocol name option here. Options to choose from are DHCP, ARP, DNS, GVRP, ICMPv4, ICMPv6-Neighbor, ICMPv6-Other, IGMP, LACP, SNMP, SSH, STP, Telnet, TFTP, Web, and 802.1X.
Page 350: Traffic Segmentation Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Type Select the trusted host type here. Options to choose from are Telnet, SSH, Ping, HTTP, and HTTPS. Click the Apply button to accept the changes made. Click the Delete button to remove the specific entry.
Page 351 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-83 Storm Control window The fields that can be configured for Storm Control Trap Settings are described below: Parameter Description Trap State Select the storm control trap option here. Options to choose from are None, Storm Occur, Storm Clear, and Both.
Page 352 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here. Type Select the type of storm attack that will be controlled here. Options to choose from are Broadcast, Multicast, and Unicast.
Page 353: Dos Attack Prevention Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-85 Storm Control (Level) window The fields that can be configured are described below: Parameter Description Level Rise Enter the rise level value used here. This option specifies the rise threshold value as a percentage of the total bandwidth per port at which traffic is received on the port.
Page 354: Ssh
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-86 DoS Attack Prevention Settings window The fields that can be configured for SNMP Server Enable Traps DoS Settings are described below: Parameter Description Trap State Select to enable or disable the DoS attack prevention trap state here.
Page 355: Ssh Global Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide • Create a user account with admin-level access using the User Accounts window. This is identical to creating any other admin-level User Account on the Switch, including specifying a password.
Page 356: Ssh Server Connection
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-88 Host Key window The fields that can be configured for Host Key Management are described below: Parameter Description Crypto Key Type Select the crypto key type used here. Options to choose from are the Rivest Shamir Adleman (RSA) key type and the Digital Signature Algorithm (DSA) key type.
Page 357: Ssl
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 9-90 SSH User Settings window The fields that can be configured are described below: Parameter Description User Name Enter the SSH user’s username used here. This name can be up to 32 characters long.
Page 358: Ssl Global Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide block. The Switch supports the 3DES EDE encryption code defined by the Data Encryption Standard (DES) to create the encrypted text. • Hash Algorithm: This part of the cipher suite allows the user to choose a message digest function which will determine a Message Authentication Code.
Page 359: Crypto Pki Trustpoint
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for Import File are described below: Parameter Description File Select Select the file type that will be loaded here. Options to choose from are Certificate and Private Key.
Page 360: Ssl Service Policy
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Delete button to remove the specified entry. SSL Service Policy This window is used to view and configure the SSL service policy settings. To view the following window, click Security > SSL > SSL Service Policy, as shown below:...
Page 361: 10. Oam
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 10. OAM Cable Diagnostics Cable Diagnostics The cable diagnostics feature is designed primarily for administrators or customer service representatives to verify and test copper cables; it can rapidly determine the quality of the cables and the types of error.
Page 362: Ddm Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide DDM Settings The window is used to configure the action that will occur for specific ports when an exceeding alarm threshold or warning threshold event is encountered. To view the following window, click OAM > DDM > DDM Settings, as show below:...
Page 363: Ddm Voltage Threshold Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 10-3 DDM Temperature Threshold Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 364: Ddm Bias Current Threshold Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Port Select the port used for the configuration here. Action Select the action that will be taken here. Options to choose from are Add and Delete. Type Select the type of voltage threshold. Options to choose from are Low Alarm, Low Warning, High Alarm, and High Warning.
Page 365: Ddm Rx Power Threshold Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 10-6 DDM TX Power Threshold Settings window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 366: Ddm Status Table
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Unit Select the switch unit that will be used for this configuration here. Port Select the port used for the configuration here. Action Select the action that will be taken here. Options to choose from are Add and Delete.
Page 367: 11. Monitoring
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 11. Monitoring Utilization Statistics Mirror Settings Device Environment Utilization Port Utilization This window is used to display the percentage of the total available bandwidth being used on the port. To view the following window, click Monitoring > Utilization > Port Utilization, as show below:...
Page 368: Statistics
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Find button to locate a specific entry based on the information entered. Click the Refresh button to refresh the display table. Statistics Port This window is used to display the packet statistics of ports.
Page 369: Port Counters
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 11-3 Port Detail window Click the Back button to return to the previous window. Click the Refresh button to refresh the display table. Port Counters This window is used to display port counter statistics.
Page 370 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 11-4 Port Counters window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 371: Counters
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 11-5 Counters Errors window Click the Back button to return to the previous window. Click the Refresh button to refresh the display table. Counters This window is used to display all port counters, and clear the port counters of the specified or all ports.
Page 372 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 11-6 Counters window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 373: Mirror Settings
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 11-7 Port Counters Detail window Click the Back button to return to the previous window. Click the Refresh button to refresh the display table. Mirror Settings This window is used to view and configure the mirror feature’s settings. The Switch allows users to copy frames transmitted and received on a port and redirect the copies to another port.
Page 374 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 11-8 Mirror Settings window The fields that can be configured for Mirror Settings are described below: Parameter Description Session Number Select the mirror session number for this entry here. This number is between 1 and 4.
Page 375: Device Environment
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Session Number. After selecting the Session Number option, select the session number from the second drop-down menu. This number is from 1 to 4. Click the Find button to locate a specific entry based on the information entered.
Page 376: 12. Green
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 12. Green Power Saving Power Saving This window is used to configure the power saving settings of the Switch. To view the following window, click Green > Power Saving, as shown below:...
Page 377: Eee
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Apply button to accept the changes made for each individual section. Click the Delete button to remove the specified entry. NOTE: The hibernation feature can only be configured when physical stacking is disabled on this switch.
Page 378 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 12-3 EEE window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. From Port / To Port Select the appropriate port range used for the configuration here.
Page 379: 13. Save And Tools
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 13. Save and Tools Save Configuration Firmware Upgrade & Backup Configuration Restore & Backup Log Backup Ping Trace Route Language Management Reset Reboot System Save Configuration This window is used to save the running configuration to the start-up configuration or the file system of the Switch.
Page 380: Firmware Upgrade From Tftp
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameter Description Unit Select the switch unit that will be used for this configuration here. Source URL Enter the source filename and path of the firmware file located on the local PC.
Page 381: Firmware Backup To Tftp
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 13-4 Firmware Backup to HTTP window The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here.
Page 382: Configuration Restore From Tftp
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide To view the following window, click Tools > Configuration Restore & Backup > Configuration Restore from HTTP, as shown below: Figure 13-6 Configuration Restore from HTTP window The fields that can be configured are described below:...
Page 383: Configuration Backup To Http
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide server in the space provided. Source URL Enter the source filename and path of the configuration file located on the TFTP server here. This field can be up to 64 characters long.
Page 384: Log Backup
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured are described below: Parameter Description Unit Select the switch unit that will be used for this configuration here. TFTP Server IP Enter the TFTP server’s IP address here. When select the IPv4 option, enter the IPv4 address of the TFTP server in the space provided.
Page 385: Ping
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 13-11 Log Backup to TFTP window The fields that can be configured are described below: Parameter Description TFTP Server IP Enter the TFTP server’s IP address here. When select the IPv4 option, enter the IPv4 address of the TFTP server in the space provided.
Page 386 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Target IPv4 Address Select and enter an IP address to be pinged. Domain Name Select and enter the domain name of the system to discover. Ping Times Enter the number of times desired to attempt to Ping the IPv4 address configured in this window.
Page 387: Trace Route
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Click the Stop button to halt the Ping Test. Click the Back button to return to the IPv4 Ping section. After clicking the Start button in IPv6 Ping section, the following IPv6 Ping Result section will appear: Figure 13-14 Ping –...
Page 388 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The fields that can be configured for IPv4 Trace Route are described below: Parameter Description IPv4 Address Select and enter the IPv4 address of the destination here. Domain Name Select and enter the domain name of the destination here.
Page 389: Language Management
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 13-16 Trace Route - IPv4 Trace Route Result window Click the Back button to stop the trace route and return to the IPv4 Trace Route section. Language Management This window is used to install the language file to the Switch.
Page 390: Reboot System
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Figure 13-18 Reset window Select the The Switch will be reset to its factory defaults including IP address and stacking information, and the will save, reboot option to reset the Switch’s configuration to its factory default settings.
Page 391: Appendix A - System Log Entries
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Appendix A - System Log Entries The following table lists all possible entries and their corresponding meanings that will appear in the System Log of this switch. 802.1X Log Description Severity Event description: 802.1X Authentication failure.
Page 392 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide client-ip: It indicates the client’s IP address if valid through IP protocol. aaa-method: It indicates the authentication method, e.g.: none, local, server. server-ip: It indicates the AAA server IP address if authentication method is remote server.
Page 393 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Event description: This log will be generated when the remote server does not Warning respond to the enable password authentication request. Log Message: Enable privilege failed through <exec-type> <from client-ip> due to AAA server <server-ip>...
Page 394 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Auto Surveillance VLAN Log Description Severity Event description: When a new surveillance device is detected on an interface. Informational Log Message: New surveillance device detected (<interface-id>, MAC: < mac- address >) Parameters description: interface-id: Interface name.
Page 395 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide unitID: The unit ID. session: The user’s session. username: Represent current login user. ipaddr: Represent client IP address. macaddr : Represent client MAC address. serverIP: Server IP address. pathFile: Path and file name on server.
Page 396 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide session: The user’s session. username: Represent current login user. ipaddr: Represent client IP address. macaddr : Represent client MAC address. serverIP: Server IP address. pathFile: Path and file name on server.
Page 397 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide address>, VLAN <vlan-id>, on <interface-id>). Parameters description: type: The type of ARP packet, it indicates that ARP packet is request or ARP response. Event description: This log will be generated when DAI detect valid ARP packet.
Page 398 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide supply voltage bias current TX power RX power high-low: High or low threshold. Event description: when the any of SFP parameters recovers from the alarm Critical threshold. Log Message: Optical transceiver <interface-id> <component> <high-low> alarm threshold exceeding back to normal.
Page 399 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide rebinding Log Message: The IPv6 address < ipv6address > on interface <ipif-name> starts rebinding. Parameters description: ipv6address: ipv6 address obtained from a DHCPv6 server. ipif-name: Name of the DHCPv6 client interface.
Page 400 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameters description: ipv6address: IPv6 prefix obtained from a delegation router. intf-name: Name of the DHCPv6 client PD interface. Event description: The IPv6 prefix obtained from a delegation router rebinds Informational success.
Page 401 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide interface-id: Interface name Interface Log Description Severity Event description: When port is down Informational Log Message: Port <port-type>< interface-id> link down Parameters description: port-type: port type interface-id: Interface name Event description: When port is up Informational Log Message: Port <port-type><...
Page 402 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide available. LACP Log Description Severity Event description: Link Aggregation Group link up. Informational Log Message: Link Aggregation Group < group_id > link up. Parameters description: group_id: The group id of the link down aggregation group.
Page 403 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Event description: Record the event when the number of VLANs that loop back has Critical occurred exceeds a reserved number. Log Message: Loop VLAN numbers overflow. Event description: When the ACL hardware resource is exhausted.
Page 404 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide 4. macAddress(4) 5. networkAddress(5) 6. interfaceName(6) 7. local(7) chassisID: chassis ID. portType: port ID subtype. Value list: 1. interfaceAlias(1) 2. portComponent(2) 3. macAddress(3) 4. networkAddress(4) 5. interfaceName(5) 6. agentCircuitId(6) 7. local(7) portID: port ID.
Page 405 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Event description: Login through console successfully. Informational Log Message: [Unit <unitID>, ]Successful login through Console (Username: <username>) Parameters description: unitID: The unit ID. username: Represent current login user. vent description: Login through console unsuccessfully.
Page 406 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Parameters description: username: Represent current login user. ipaddr: Represent client IP address. Event description: Login through SSH unsuccessfully. Critical Log Message: Login failed through SSH (Username: <username>, IP: <ipaddr>) Parameters description: username: Represent current login user.
Page 407 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Event description: The authorized user number on the whole device is below the Warning maximum user limit in a time interval. Log Message: MAC-based Access Control recovers from stop learning state.
Page 408 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide information. Event description: Used to record MSTP instance port state change event. Notice Log Message: Spanning Tree port status change (Instance :< Instance-id >, <interface_id>) <old_status> -> <new_status> Parameters description: Instance-id: MST instance id.
Page 409 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide (instance: <Instance-id> add vlan <startvlanid> [- <endvlanid>]) Parameters description: Instance-id: MST instance id. Instance 0 represents for default instance, CIST. startvlanid: The start vid of add vlan range. endvlanid: The end vid of add vlan range.
Page 410 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide thermal-sensor-descr: The sensor ID and position. Event description: Power failed. Critical Log Message: Unit <unit-id> <power-descr> failed Parameters description: unitID: The unit ID. power-descr: The power position and ID. Event description: Power is recovered.
Page 411 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Event description: the host enters the mode of exhausted. Warning Log Message: Unit <unit-id>, Safeguard Engine enters EXHAUSTED mode. Parameters description: unit-id: The Unit ID Event description: the host enters the mode of normal.
Page 412 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Macaddr: MAC address. Event description: Stacking topology change. Informational Log Message: Stacking topology is <Stack_TP_TYPE>. Master(Unit <unitID>, MAC:<macaddr>). Parameters description: Stack_TP_TYPE: The stacking topology type is one of the following: 1.
Page 413 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide interface-id: The interface ID on which a storm is cleared. Event description: Port shut down due to a packet storm Warning Log Message: <interface-id> is currently shut down due to the <Broadcast | Multicast | Unicast>...
Page 414 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Event description: Web session timed out. Informational Log Message: Web session timed out (Username: <usrname>, IP: <ipaddr>). Parameters description: username: The use name that used to login HTTP server. ipaddr: The IP address of HTTP client.
Page 415: Appendix B - Trap Entries
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Appendix B - Trap Entries The following table lists all possible trap log entries and their corresponding meanings that will appear in the switch. 802.1X Trap Name Description dDot1xExtLoggedSuccess The trap is sent when a host has successfully logged 1.3.6.1.4.1.17...
Page 416 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name Description dDdmAlarmTrap A notification is generated when an abnormal alarm 1.3.6.1.4.1.17 situation occurs, or recovers from an abnormal alarm 1.14.72.0.1 situation to normal status. Binding objects: (1) dDdmNotifyInfoIfIndex...
Page 417 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Binding objects: (1) dErrDisNotifyInfoPortIfIndex (2) dErrDisNotifyInfoReasonID dErrDisNotifyPortDisabledClear The trap is sent when a port loop restarts after the 1.3.6.1.4.1.17 interval time. 1.14.45.0.2 Binding objects: (1) dErrDisNotifyInfoPortIfIndex (2) dErrDisNotifyInfoReasonID General Management...
Page 418 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide (but not into the notPresent state). This other state is indicated by the included value of ifOperStatus. Binding objects: (1) ifIndex, (2) if AdminStatus (3) ifOperStatu linkDown A linkDown trap signifies that the SNMP entity, acting 1.3.6.1.6.3.1.
Page 419 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide (3) lldpStatsRemTablesDrops (4) lldpStatsRemTablesAgeouts lldpXMedTopologyChangeDetect A notification generated by the local device sensing a 1.0.8802.1.1. change in the topology that indicates that a new 2.1.5.4795.0. remote device attached to a local port, or a remote device disconnected or moved from one port to another.
Page 420 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide trap is sent by a bridge soon after its election as the new root, e.g., upon expiration of the Topology Change Timer, immediately subsequent to its election. Implementation of this trap is optional.
Page 421 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide dPoeIfPowerDeniedNotification This Notification indicates if PSE state diagram 1.3.6.1.4.1.17 enters the state POWER_DENIED. At least 500 1.14.24.0.1 msec must elapse between notifications being emitted by the same object instance. Binding objects:...
Page 422 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name Description risingAlarm The SNMP trap that is generated when an alarm 1.3.6.1.2.1.16 entry crosses its rising threshold and generates an .0.1 event that is configured for sending SNMP traps.
Page 423 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide dStackTPChangeNotification The stacking topology change notification. 1.3.6.1.4.1.17 1.14.9.0.4 Binding objects: (1) dStackNotifyInfoTopologyType (2) dStackNotifyInfoBoxId (3) dStackInfoMacAddr dStackRoleChangeNotification The stacking unit role change notification. 1.3.6.1.4.1.17 1.14.9.0.5 Binding objects: (1) dStackNotifyInfoRoleChangeType (2) dStackNotifyInfoBoxId...
Page 424 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide when its member generates a topology change 1.12.8.6.0.17 notification. Binding objects: (1) swSingleIPMSID (2) swSingleIPMSMacAddr Start Trap Name Description coldStart A coldStart trap signifies that the SNMPv2 entity, 1.3.6.1.6.3.1. acting in an agent role, is reinitializing itself and that 1.5.1...
Page 425 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Trap Name Description dWebAuthLoggedSuccess The trap is sent when a host has successfully logged 1.3.6.1.4.1.17 in (passed Web-Authentication). 1.14.154.0.1 Binding objects: (1) ifIndex (2) dnaSessionAuthVlan (3) dnaSessionClientMacAddress (4) dnaSessionClientAddrType (5) dnaSessionClientAddress...
Page 426: Appendix C - Radius Attributes Assignment
DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Appendix C - RADIUS Attributes Assignment The RADIUS Attributes Assignment on the DGS-1510 is used in the following modules: Console, Telnet, SSH, Web, 802.1X, MAC-based Access Control, JWAC, and WAC.
Page 427 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide not configure the bandwidth attribute and authenticates successfully, the device will not assign any bandwidth to the port. If the bandwidth attribute is configured on the RADIUS server with a value of “0”, the effective bandwidth will be set “no_limited”, and if the bandwidth is configured less than “0”...
Page 428 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide The table below shows the definition of Tag field (different with RFC 2868): Tag field value String field format 0x01 VLAN name (ASCII) 0x02 VLAN ID (ASCII) Others When the switch receives the VLAN setting string, it will think it is the VLAN ID first.
Page 429: Appendix D - Ietf Radius Attributes Support
RADIUS attributes currently supported by the switch. RADIUS attributes are supported by the IETF standard and Vendor-Specific Attribute (VSA). VSA allows the vendor to create an additionally owned RADIUS attribute. For more information about D-Link VSA, refer to the RADIUS Attributes Assignment Appendix.
Page 430 DGS-1510 Series Gigabit Ethernet SmartPro Switch Web UI Reference Guide Message-Authenticator Tunnel-Private-Group-ID Acct-Interim-Interval NAS-Port-ID NAS-IPv6-Address RADIUS Accounting Attributes: Number IETF Attribute User-Name NAS-IP-Address NAS-Port Service-Type Framed-IP-Address Calling-Station-ID NAS-Identifier Acct-Status-Type Acct-Delay-Time Acct-Input-Octets Acct-Output-Octets Acct-Session-ID Acct-Authentic Acct-Session-Time Acct-Input-Packets Acct-Output-Packets Acct-Terminate-Cause Acct-Input-Gigawords Acct-Output-Gigawords...

D-Link DGS-1510 Series Web Ui Reference Manual

1 Introduction

2 Web-Based Switch Configuration

3 System

4 Management

5 Layer 2 Features

6 Layer 3 Features

7 Quality of Service (Qos)

8 Access Control List (ACL)

9 Security

10 Oam

11 Monitoring

12 Green

13 Save and Tools

Appendix A - System Log Entries

Appendix B - Trap Entries

Appendix C - RADIUS Attributes Assignment

Appendix D - IETF RADIUS Attributes Support

Quick Links

Related Manuals for D-Link DGS-1510 Series

Summary of Contents for D-Link DGS-1510 Series