Table of Contents
Advertisement
Quick Links
Introduction
This Technical Manual describes the system boards of the PRIMERGY 870 server systems, which
can be equipped with up to four Intel Xeon processors.
You may find further information in the description "BIOS Setup".
Further information to drivers is provided in the readme files on hard disk or on the supplied drivers
diskettes or on the "Drivers & Utility" or "ServerStart" CD.
Notational conventions
The meanings of the symbols and fonts used in this manual are as follows:
Pay particular attention to texts marked with this symbol. Failure to observe this warning
!
endangers your life, destroys the system, or may lead to loss of data.
This symbol is followed by supplementary information, remarks and tips.
i
²
Texts which follow this symbol describe activities that must be performed in the order shown.
Texts in italics indicate commands or menu item.
"Quotation marks" indicate names of chapters and terms that are being emphasized.
Overview
The PRIMERGY 870 server systems mainly consist of the following plug-in boards:
•
I/O board
•
Processor board
•
Memory board (2x)
•
Interface board
•
SCSI board (3x)
•
Power supply board
•
ECU board
•
Drive board (2x)
U41029-J-Z146-1-7400
English - 1
Advertisement
Table of Contents
Related Manuals for Fujitsu PRIMERGY 870
Summary of Contents for Fujitsu PRIMERGY 870
-
Page 1: Introduction
Introduction This Technical Manual describes the system boards of the PRIMERGY 870 server systems, which can be equipped with up to four Intel Xeon processors. You may find further information in the description "BIOS Setup". Further information to drivers is provided in the readme files on hard disk or on the supplied drivers diskettes or on the "Drivers &... -
Page 2: Abbreviations
Introduction Abbreviations Abbreviations ASIC Application Specific Integrated Circuit ASR&R Automatic Server Recovery & Restart BIOS Basic Input Output System Controller Area Network (CAN-Bus) Central Processing Unit Disk Array Controller DIMM Dual Inline Memory Module Dual Inline Package Direct Memory Access Environment Control Unit EDO-DRAM Enhanced Data Output Dynamic Random Access Memory... -
Page 3: Important Notes
Abbreviations Important notes Important notes Store this manual close to the device. If you pass on the device to third parties, you should also pass on this manual. Be sure to read this page carefully and note the information before you open the Server. Please note the information provided in the chapter "Safety"... -
Page 4: I/O Board
I/O board Abbreviations I/O board Features • Intel Chipset 82450NX • 512 Kbytes Flash BIOS • Intel i960 processor for PCI-to-PCI-Bridge, I O and Server Management • Intel 82527 CAN controller • Intel 82558 Fast Ethernet LAN controller • two Symbios 53C875 Ultra Wide SCSI controller •... -
Page 5: Interfaces And Connectors
Interfaces and connectors I/O board Interfaces and connectors 1 = SCSI 1 16 bit 9 = Hot-plug PCI panel for 64 bit slots 2 = SCSI 2 16 bit 10 = Hot-plug PCI panel for 32 bit slots 3 = Cover detection 11 = Keyboard and mouse 4 = ECU 12 = USB... -
Page 6: Possible Screen Resolution
I/O board Possible screen resolution Possible screen resolution Depending on the operating system used the screen resolutions in the following table refer to the screen controller on the I/O board. If you are using an external screen controller, you will find details of supported screen resolutions in the Operating Manual or Technical Manual supplied with the controller. -
Page 7: Settings With The Switch Block
Settings with the switch block I/O board Settings with the switch block Switch 1 to 5 = not used Switch 7 = Skipping password query Switch 6 = Write protection for floppy disks Switch 8 = Recovering system BIOS English - 7 U41029-J-Z146-1-7400... - Page 8 I/O board Settings with the switch block Write protection for floppy disks - switch 6 Switch 6 is used to define whether floppy disks can be written or deleted in the floppy disk drive. To write and delete floppy disks, the write -protection in BIOS setup must be disabled (in menu Security, the field Diskette Write must be set to Enabled).
-
Page 9: Add-On Modules
Add-on modules I/O board Add-on modules 1 = Battery 7 = 32 bit PCI slots (bus 1-i960) 2 = Slots for i960 memory (odd) 8 = 32 bit PCI slots (bus 0-0A) 3 = Slots for i960 memory (even) 9 = 32 bit Hot-plug PCI slots (bus 2-0B) 4 = Flash BIOS 10 = 64 bit Hot-plug PCI slots (bus 3-1A) 5 = Interface board... -
Page 10: Memory Extension For I960
I/O board Add-on modules Memory extension for i960 The I/O board is equipped with two installation banks (even and odd) for memory modules. Both memory banks can be equipped with single-sided or double-sided memory modules. Equipping must begin with the even installation bank. The board supports a maximum of 16 Mbytes. -
Page 11: Isa Bus Resources
Add-on modules I/O board ISA bus resources Device Address Keyboard Serial port COM 2 03F8, 02F8, 03E8, 02E8 03F8, 02F8, 03E8, 02E8 Serial interface COM1 Floppy disk drive controller Parallel interface LPT1 0278, 0378, 03BC 0, 1, 3 Real-time clock (RTC) free 9, 10, 11 Mouse controller... -
Page 12: Pci Bus Resources
I/O board Add-on modules PCI bus resources PCI slots The following table shows an overview of the PCI slots: Label PCI bus name 64bit/ Shared Description slot # 32bit Plug X100 PCI-Bus 3-1A 64 bit 64 bit hot-plug PCI bus slot X101 PCI-Bus 3-1A 64 bit... - Page 13 Add-on modules I/O board PCI device numbers The following table shows the device numbers assigned to the PCI devices and PCI slots on the I/O board: PCI bus PCI bus Device PCI-AD Device number number PCI-Bus 0-0A AD18 PIIX4 PCI-Bus 0-0A AD19 PCI-Bus 0-0A AD20...
- Page 14 I/O board Add-on modules PCI bus slots and PCI bus devices The following table shows the assignment of the four different PCI buses to the PCI slots and PCI devices. PCI bus name PCI bus Slot/Devic 64 bit/ Hot- Shared Description number slot...
- Page 15 Add-on modules I/O board Interrupt Request Levels The following applies to all four PCI buses: All INTA# PCI interrupts of a PCI bus are carried on various PCI bus interrupts of the PCI interrupt controller (MINT-ASIC or MINT-ASIC plus PIIX4 for PCI bus 0A).
- Page 16 I/O board Add-on modules PCI-Bus 3-1A The PCI bus interrupts of the 64 bit hot-plug PCI bus, PCI bus 3-1A, are only carried on the MINT- ASIC. MINT PCI bus Slot 1 Slot 2 Slot 3 Slot 4 interrupt Bus 3-1A Slot 1 Bus 3-1A Slot 2 Bus 3-1A Slot 3 Bus 3-1A Slot 4...
-
Page 17: Replacing The Lithium Battery
Add-on modules I/O board Replacing the lithium battery Incorrect replacement of the lithium battery may lead to a risk of explosion. The lithium battery must be replaced with an identical battery or a battery type recommended by the manufacturer (CR2032). Do not throw lithium batteries into the trashcan. -
Page 18: Processor Board
Processor board Add-on modules Processor board The CPU modules and the memory boards are plugged onto the processor board. LED 8 LED 1 1 = Power supply 6 = Indicators (LED) 2 = Voltage regulator 7 = CPU 3 3 = Memory board 1 8 = CPU 2 4 = Memory board 0 9 = CPU 1... -
Page 19: Memory Boards
Add-on modules Memory boards Memory boards The memory board is equipped with 16 slots for memory modules. The organization in four memory banks A to D enables fast memory access with four-fold interleave. The maximum memory configuration is 4 Gbytes per memory board. Four identical memory modules must be installed per memory bank. -
Page 20: Power Supply Board
Power supply board Add-on modules Power supply board The power supply board makes the connection between the power supply modules and the other system components. 5 6 7 1 = Control panel 12 = Cover - power supply 2 = Power supply for hard disk drives 13 = Power supply unit - Power supply 1 3 = Accessible drives 14 = Power supply unit - Power supply 2... -
Page 21: Interface Board
Add-on modules Interface board Interface board The interface board makes several of the external standard interfaces available. It is installed in a special slot on the I/O board. 1 = Monitor (VGA) 6 = Serial port (COM 2) 2 = Parallel port (LPT) 7 = Serial port (COM 1) 3 = Serial port (COM 4) 8 = Serial port (COM 4) -
Page 22: Scsi Board
SCSI board Add-on modules SCSI board The SCSI board connects a group of four SCSI hard disk drives to the SCSI bus. SCSI ID 3 SCSI ID 2 SCSI ID 1 SCSI ID 0 1 = Remote power-on jumper (opt.) 5 = Test connection 2 = Power supply 6 = SCSI input... -
Page 23: Saf-Te/Terminator Board
STM-SE SAF-TE/Terminator board SAF-TE/Terminator board The SAF-TE/terminator board (STM) is installed on the plug SCSI output and OLR controller on the SCSI board (piggy back). The SAF-TE/terminator board terminates the SCSI bus and runs the SAF-TE protocol including OLR. The SAF-TE/terminator board is available in a single-ended (SE) and in a low-voltage differential (LVD) version. -
Page 24: Stm-Lvd
SAF-TE/Terminator board STM-LVD STM-LVD 1 = OLR control to SCSI board 4 = OLR control to SCSI board 2 = SCSI bus to SCSI board 5 = Standard code jumper 3 = Housing diagnosis connection 6 = ISP 24 - English U41029-J-Z146-1-7400... -
Page 25: Ecu Board
STM-LVD ECU board ECU board The ECU board is located in the control panel slide-in module. 1 = Chipcard reader 3 = Floppy disk drive 2 = Control panel 4 = Power supply for floppy disk drive English - 25 U41029-J-Z146-1-7400... -
Page 26: Drive Board
Drive board 8 bit SCSI Drive board The drive board makes the connection between the drives and the SCSI system in the drive slide-in module for accessible drives. The drive board is available in an 8-bit wide and a 16-bit wide SCSI version. -
Page 27: Bit Scsi
16 bit SCSI Drive board 16 bit SCSI 1 = Power supply for accessible drives 3 = SCSI connection for SV board 2 = SCSI connection for accessible drive English - 27 U41029-J-Z146-1-7400... -
Page 28: Index
Index 16 bit SCSI 8 bit SCSI ASIC ASR&R Battery Battery, replacing BIOS CAN 2, controller CAN bus Chipcard reader Chipset Control panel CPU 2, DAC 2, Device ID DIMM 2, Drive board 16 bit SCSI 8 bit SCSI Drive LEDs ECU 2, ECU board EDO DRAM 2,... - Page 29 Index Floppy disk drive controller Graphics controller 4, Hot-plug PCI panel Hot-plug PCI slots Housing detection Housing diagnosis connection I/O board I2O controller i960 memory extension processor ID-DIP switch IDE drives IDE hard disk controller IDE power supply Important notes Installing, memory module Interface board Interrupt assignment...
- Page 30 Index Monitor Mouse Notational conventions OLR 2, 22, OLR control Parallel interface Password query, skipping PCI bus 0-0A 1-i960 2-0B 3-1A devices names resources slots PCI device numbers PCI slots 4, PCI-to-PCI bridge PIIX4 Power supply Power supply board Priority, slot Processor board PS/2 keyboard port PS/2 mouse port...
- Page 31 Index SCSI 1 16 bit SCSI 2 16 bit SCSI board SCSI controller SE 2, Serial interface 4, Slot priority Slots Specification, memory modules STM-LVD STM-SE System BIOS recovering System fan USB 2, 4, VGA 2, VGA controller Voltage regulator Wake on LAN Wake up on LAN Write-protection for floppy disks...
-
Page 33: Table Of Contents
Contents Introduction............................1 Notational conventions ........................1 Overview ............................1 Abbreviations.............................2 Important notes..........................3 board............................4 Interfaces and connectors........................5 Possible screen resolution .........................6 Settings with the switch block ......................7 Add-on modules..........................9 Memory extension for i960.......................10 Equipping sequence/slot priority ....................10 ISA bus resources ........................11 PCI bus resources ........................12 Replacing the lithium battery....................17... - Page 34 U41029-J-Z146-1-7400 PRIMERGY 870 System Boards Technical Manual August 1998 edition IIntel is a registered trademark of Intel Corporation, USA. PS/2 is a registered trademark of International Business Machines, Inc. All other trademarks referenced are trademarks or registered trademarks of their respective owners, whose protected rights are acknowledged.
- Page 35 Information on this document On April 1, 2009, Fujitsu became the sole owner of Fujitsu Siemens Compu- ters. This new subsidiary of Fujitsu has been renamed Fujitsu Technology So- lutions. This document from the document archive refers to a product version which was released a considerable time ago or which is no longer marketed.