Summary of Contents for Sony HANDYCAM DCR-TRV130ERMT-814
Page 1
DCR-TRV130E RMT-814 SERVICE MANUAL SERVICE MANUAL SERVICE MANUAL AEP Model UK Model Level 1 Ver 1.0 2001. 01 M2000 MECHANISM SPECIFICATIONS DIGITAL VIDEO CAMERA RECORDER...
Page 2
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
Additional Information About video cassettes ····························································· 45 About the “InfoLITHIUM” battery pack ································ 46 About i.LINK ·········································································· 46 Using your camcorder abroad ················································· 47 Maintenance information and precautions ······························ 47 Quick Reference Identifying the parts and controls ··········································· 49 — 3 —...
POWER SUPPLY DURING REPAIRS In this unit, about 10 seconds after power is supplied (8.4V) to the battery terminal using the service power code (J-6082-223-A), the power is shut off so that the unit cannot operate. These following two methods are available to prevent this. Take note of which to use during repairs. Method 1.
Self-diagnosis Function When problems occur while the unit is operating, the self-diagnosis function starts working, and displays on the viewfinder or LCD or Display window what to do. This function consists of two display; self-diagnosis display and service mode display. Details of the self-diagnosis functions are provided in the Instruction manual.
Self-diagnosis Code Table Self-diagnosis Code Block Detailed Function Code Non-standard battery is used. Condensation. Video head is dirty. LOAD direction. Loading does not complete within specified time UNLOAD direction. Loading does not complete within specified time T reel side tape slacking when unloading. S reel side tape slacking when unloading.
Page 7
Self-diagnosis Code Block Detailed Function Code Difficult to adjust focus (Cannot initialize focus.) Zoom operations fault (Cannot initialize zoom lens.) Handshake correction function does not work well. (With pitch angular velocity sensor output stopped.) Handshake correction function does not work well. (With yaw angular velocity sensor output stopped.) Symptom/State Inspect the lens block focus reset sensor (Pin qs of CN1551 of...
DCR-TRV130E Note: • Follow the disassembly procedure in the numerical order given. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items. • The parts numbers of such as a cabinet are also appeared in this section. Refer to the parts number mentioned below the name of parts to order.
NOTE: Follow the disassembly procedure in the numerical order given. 2-1. VIDEO LIGHT 1 Push in the dent inside hole with wire tip. 2-2. LCD SECTION (PD-131 BOARD) 4 P cabinet C 2 MI screw 4) (H) 9 PD-131 board, Panel frame 8 Back light Cold cathode...
2-3. FRONT PANEL SECTION (MI-041 BOARD) 1 Open the jack cover 3 MI screw 4) (H) 2 Two MI screws 4) (H) 7 Front panel section 2 Microphone (Lch) (2P) 1 Microphone (Rch) (2P) 2-4. CABINET (L) SECTION 6 Two MI screws 4) (H) 4 Two MI screws 4) (H)
2-5. CABINET (R) SECTION, CONTROL SWITCH BLOCK (CF-1000) 1 MI screw 4) (H) 4 Claw 2 MI screw 4) (H) 7 Cabinet (R) section 6 FFC-295 flexible flat cable (24P) 5 Harness 3 Three MI screws (PD-110) (20P) 4) (H) 7 Remove the control switch block (CF-1000) in the direction of the arrow A B .
2-6. EVF SECTION (VF-129 BOARD) 1 FFC-289 flexible flat cable (4P) 3 Finder (S) assembly Rotate it in the direction of the arrow B and remove it in the direction of the arrow C . 2 Slide the button in the 2 Two tapping screws (B2 3 EVF section...
REPAIR PARTS LIST 3-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may have some differences from the original one. • Items marked “*” are not stocked since they are seldom required for routine service. Some delay should be anticipated when ordering these items.
3-1-5. CABINET (R) SECTION : BT001 (Lithium battary) CF-1000 on the mount position. The printed wiring board of the Control switch block (CF-1000) on which lithium battery is mounted, is not shown.] Ref. No. Part No. Description 3-948-339-61 TAPPING 3-065-436-01 BLIND (12), HINGE 1-476-425-21 SWITCH BLOCK, CONTROL (CF-1000) X-3951-223-1 CABINET R (12) ASSY 3-059-539-11 LID (103P), CPC...
3-1-6. LCD SECTION Ref. No. Part No. Description 3-067-347-01 MI SCREW M2 (H) 3-065-474-01 CABINET C (12), P * 253 3-058-672-01 CLAMP, HARNESS 3-948-339-31 SCREW, TAPPING 3-065-477-01 COVER C (12), HINGE X-3951-206-1 HINGE (12) ASSY 1-960-975-11 HARNESS (PD-110) 3-065-478-01 COVER M (12), HINGE 4-974-725-01 SCREW (M1.7X2.5), P Remarks Ref.