1. Manuals
  2. Brands
  3. Beko Manuals
  4. Oven
  5. CSM 63320 DSL
  6. Service manual

Beko CSM 63320 DSL Service Manual

Better timer built in bi oven
Hide thumbs Also See for CSM 63320 DSL:
Table of Contents

Advertisement

Quick Links

Download this manual
BARBAROS-BEKO-2014
BETTER TIMER BUILT IN BI OVEN
SERVICE MANUAL
1 | TR
Sensitivity: Public

Advertisement

Table of Contents
loading

Related Manuals for Beko CSM 63320 DSL

Summary of Contents for Beko CSM 63320 DSL

  • Page 1 BARBAROS-BEKO-2014 BETTER TIMER BUILT IN BI OVEN SERVICE MANUAL 1 | TR Sensitivity: Public...

  • Page 2: Table Of Contents

    1.Cover 2. TABLE OF CONTENTS 1.COVER ............................2 2. SAFETY WARNING ........................5 2.1 G ..........................5 ENERAL AFETY 2.2. S ......................5 AFETY FOR ONFİGURATİONS 2.3 I ......................6 NFORMATİONS FOR ONSUMER 3.TECHNICAL SPECIFICATIONS ...................... 7 4. PRODUCT ASSEMBLY/ ASSEMBLY RULES/ SETTINGS ..............8 4.1 P ........................
  • Page 3 9.FAULT/ERROR CODES ......................52 9.1 H ......................... 52 ARDWARE RRORS 9.2 H -2 ........................53 ARDWARE RRORS 9.3 ON/OFF ............... 54 ALARM LAMPAND TART STOP BUTTON ERRORS 9.4 T ........................55 OUCH ONTROL RRORS 9.5 PT 500 E -1 .......................... 56 RRORS 9.6 PT 500 E -2 ..........................
  • Page 4 11.14 R ......................100 EMOVING THE REAR WALL 11.15 R ......................103 EMOVING THE IDE DECOR 11.16 C ..................103 HANING THE BOTTOM OF THE BASE PLATE 11.17 C ......................... 105 HANİNG THE SWİTCH 11.18 C ................. 107 ATALYTIC REMOVAL OF THE INNER SIDE WALL 11.19 C ....................

  • Page 5: Safety Warning

    2. SAFETY WARNING This section contains safety instructions that will help protect from risk of personal injury or property damage. Throughout this user manual the following symbols are used. Important information or useful hints about usage. Warning of hazardous situations with regard to life and property. Warning of electric shock..

  • Page 6: Informations For Consumer

    2.3 Informations for Consumer  Product may be hot during the usage.Do not touch with hot parts ,inside the oven,heating components etc. .When the product is working it is hot so do not put combustable materials near the product.  Do not wash the product with water! It is dangerous for electrick shock!Ürünü, üzerine s ...

  • Page 7: Technical Specifications

    3.TECHNICAL SPECIFICATIONS 7 | TR Sensitivity: Public...

  • Page 8: Product Assembly/ Assembly Rules/ Settings

    4. PRODUCT ASSEMBLY/ ASSEMBLY RULES/ SETTINGS 4.1 Product Transportation To carry or move the product, do not use door or handle of the product. Door, handle or hinges can be harmed. Product should be carried by two person for safety of the product and ergonomics When the product is being carried or the product is being put to the ground, do not put it keenly, do not drag it and do not skid it from...

  • Page 9: Unpacking Product

    4.2 Unpacking Product To consider product changing in the mounting process, please do not harm package, product and the product package when extracting. Extract package with a knife without harming top and bottom carton. Take the top carton. Take lathes on the product’s front and behind sides, like shown in below. 9 | TR Sensitivity: Public...

  • Page 10: Controlling The Setup Place And Energy Sources

    Take stripers which are left and right side of the products. Symbols on the package of the products and meaning of them; Do not carry Carry the product Carry with Preserve the product in this way by Do not step on Fragile barrow in from damp...

  • Page 11: Instead Of Mounting The Product

    Product is designed according to kitchens’ bench so it is placeable. Appropriate safety interval should be between kitchen wall and the furniture. For appropriate interval, please look at the picture.(values are mm type). Used sides, synthetic laminates and glues should be durable to the head (min.100°C). Product should be stayed with the same height with kitchen furnitures.
  • Page 12 Right and left in the oven (as shown in the figure) screw holes for mounting the furnace furnishings. Oven, secure by means of screws as shown. The following values for the control of electrical installation products with the product should be considered.

  • Page 13: Electrical Connection

    4.3.3 Electrical connection Connect the product to a grounded outlet/line protected by a fuse of suitable capacity as stated in the "Technical specifications" table. Have the grounding installation made by a qualified electrician while using the product with or without a transformer. Our company shall not be liable for any damages that will arise due to using the product without a grounding installation in accordance with the local regulations.

  • Page 14: Use Of The Product

    5.Use Of The Product Plug in the power cord and turn on the device fuse. The language setting of the clock setting before you need to do. Each value you set, it is automatically saved when you exit the current menu. NOTE: NOTE: Before using the oven, adjust the time 5.1 Initial Use...
  • Page 15 Press the button until the icon appears at short intervals. / Buttons to set the time by touching. Confirm the setting by tapping the button. 15 | TR Sensitivity: Public...

  • Page 16: Starting The Oven

    5.2 Starting the oven 1 ON/OFF key 2 Function display 3 Current time indicator field 4 Oven Inner Temperature symbol 5 Temperature indicator field 6 Start/stop cooking key 7 Temperature setting key Booster symbol (rapid pre- heating) 9 Plus key 10 Minus key 11 Adjustment key 12 Return Key to function display...

  • Page 17: Selecting The Temperature And Operating Mode

    1- Includes pushing out after removing the button, make your setting. 2- When cooking is finished, switch off (top) inwards bringing the position. Display Symbols; : Cooking Time symbol : End of Cooking Time symbol : Function number : Alarm symbol : Clock symbol : Keylock symbol : Open door symbol...
  • Page 18 If you want to make changes to the proposed special aminothiazole the work function by pressing the button to activate the temperature field. Set the desired temperature by touching the key. touching touching check the temperature setting to confirm the set temperature.
  • Page 19 Meal, place in oven. Start cooking temperature and operating functions by tapping the appropriate button. Symbol appears. Turning off the electric furnace; Tap the button for a long time, turn off the oven. 19 | TR Sensitivity: Public...

  • Page 20: Powering The Grid

    5.2.3 Powering the Grid Tap the button to turn on the oven for a long time. Select the desired function by tapping keys on the grid. If you want to change the temperature, one touch of the button reaches the temperature setting display.
  • Page 21 Set the desired temperature by touching the key. Start tapping keys to long to cook. Cooking starts and appears on the screen. Increases the temperature inside the oven is now at the level of the middle of the symbol. Closing the grid; 1.
  • Page 22 Tap the button after opening the oven comes first work function screen. Select the operating functions by touching the key. If you want to make changes to the proposed special aminothiazole the work function by pressing the button to activate the temperature field.
  • Page 23 Set the desired temperature by touching the key. Touch to confirm the temperature setting. Tap on the screen until the symbol for the cooking time. 23 | TR Sensitivity: Public...
  • Page 24 Confirm the setting by touching the ayarlayın.tuş the cooking time by touching the key. Constant symbol will appear on the screen after the cooking time is set. Meal, place in oven. Temperature, start work function and cooking time to cook while tapping the appropriate button.
  • Page 25 After cooking is complete the message "End" appears and the alarm sounds. To set the cooking end time of a further hour; Tap the button after opening the oven comes first work function screen. / Button to select the operating functions by touching.
  • Page 26 If you want to make changes to the proposed special aminothiazole the work function by pressing the button to activate the temperature field. Buttons to set the desired temperature by touching. Tap on the screen until the symbol for the cooking time. Button to adjust the cooking time by touching.
  • Page 27 Meal, place in oven. Temperature, work function, cooking time and cooking end time to start cooking while tapping the appropriate button. Symbol appears. After cooking is complete the message "End" is displayed and the alarm signal. 27 | TR Sensitivity: Public...

  • Page 28: Work Functions

    5.3 Work Functions Top and bottom heating Food is heated simultaneously from the top and bottom. For example, it is suitable for cakes, pastries, or cakes and casseroles in baking moulds. Cook with one tray only. Suitable rack position will be displayed on screen.
  • Page 29 "3D" function Top heating, bottom heating and fan assisted heating are in operation. Food is cooked evenly and quickly all around. Cook with one tray only. Pizza function The bottom heating and fan assisted heating are in operation. Suitable for baking pizza. Full grill+Fan Hot air heated by the full grill is distributed very fast in the oven...
  • Page 30 Grill Small grill at the ceiling of the oven is in operation. Suitable for grilling and gratin dishes. Bottom heating Only bottom heating is in operation. It is suitable for pizza and for subsequent browning of food from the bottom Keep warm Used for keeping food at a temperature ready for serving for...

  • Page 31: Booster (Rapid Heating) To Be Adjusted To

    5.3.1 Booster (rapid heating) to be adjusted to Oven Booster to bring the desired temperature faster (faster preheating) use the function. 1 ON/OFF key 2 Function display 3 Current time indicator field 4 Oven Inner Temperature symbol 5 Temperature indicator field 6 Start/stop cooking key 7 Temperature setting key Booster symbol (rapid pre-...

  • Page 32: Using The Key Lock

    To cancel the booster function, touch the button again. After reaching the desired temperature inside the oven and the oven symbol will, prior to the Booster will continue to work on the selected function. To cancel the booster function, touch the button again. "Symbol disappears and the booster (Fast preheating) setting is disabled.
  • Page 33 The display shows "OFF" appears. activate the key lock button. »Display after key lock is set to" On "appears and stays illuminated. tapping confirm. Deactivating the key lock; Touch until the symbol on the screen. "On" appears. 33 | TR Sensitivity: Public...

  • Page 34: Alarm System Using The Time

    to disable the keylock touching. After key lock is deactivated the display shows "OFF" appears. tapping confirm. 5.3.3 Alarm System Using the Time Product time, no warning except cooking program, or you can use as a reminder. Alarm clock, there is no effect on the oven functions. Warning purposes. For example, the food in the oven alarm clock you can use when you want to dial a certain time.
  • Page 35 / Keys set the alarm time. »Symbol remains lit even after adjusting the alarm time and alarm time appears on the display. After expiry of the alarm time starts flashing and the alarm sounds symbol. To cancel the alarm; Audible warning alarm for two minutes.

  • Page 36: By Products/Products Labels Used

    6.BY PRODUCTS/PRODUCTS LABELS USED 6.1 PeripheralAccessories Oven Tray Used for roasting and for placing the food to be baked, roasted or cooked in casserole dishes to the desired rack. Cake Tray Used for pastries, frozen foods and big roasts. Wire Grid Cooking Start / Stop button (9) Press Start to cook.

  • Page 37: Tags And Descriptions Used In The Product

    6.2 Tags and Descriptions used in the product 6.2.1 Type the label Given information on the product nameplate label on the product gas. Sticker on the location; According to the type of product, or the product can be seen in the front door or the rear wall of the lower lid is opened.

  • Page 38: Energy Label

    Barcode label location; Product packaging is pasted on cardboard. 6.2.3 Energy Label; Product energy label product energy class, the label shows the volume of the product. Sensitivity: Public...
  • Page 39 Sensitivity: Public...
  • Page 40 Energy Label lacatıon; Energy label products are in a group of periodicals. Sensitivity: Public...

  • Page 41: Genarel Working Principle

    7. GENAREL WORKING PRINCIPLE Grundıg electronically controlled furnaces used in electronic control circuit (module) oven function control, time of day, analog and digital format show, the cooking book and choosing to eat, cooking recipes demonstration of the cooking book and automatic cooking to be done, cooking time display, timer (count backwards to set the time , give audible warning when time runs out) and allows control of the internal temperature of the oven.
  • Page 42 continues to run, an error message is written to the microprocessor. When you enter the service menu screen where the error occurred, which is written. Oven against any improper operation is protected by a bi-metal type thermal circuit breaker . Pyro kilns furnaces external cutting bi-metal type thermal oven , left rear upper side of the frame and the operation temperature is 250 °...

  • Page 43: Operating Modes

    LED panel can be damaged easily. Please follow instructions explained below. Correct Hold the component from LCM corners by antistatic gloves. Do not hold LCD from sides. False Don not touch IC directly. Do not keep LCMs as shown figure. Storage temperature must be between 0°C-35°C.

  • Page 44: The Normal Operatıng Mode

     Electronic control provides two different modes of operation.  The normal operating mode  Servıce Mode 7.1.1 The Normal Operatıng Mode Oven functions work normally, walkable oven cooking mode. In this mode, the plug is inserted into the oven starts for the first time. Normal operation mode, the following functions are working.

  • Page 45: Fast Heating / Booster

    7.1.2 Fast heating / Booster Quick heating function can be selected with the cooking function. Quick heating function in the selected position on the heater models with turbo heater unlike the combination turbo heater provides lower heater and fan motor working oven to the desired temperature more quickly reach the bottom heater in the non-turbo heater model, grid heater (internal) and fan motor work than the desired temperature of the oven provides rapid access when the oven reaches the desired temperature in the selected combination heater heater will work.
  • Page 46 * The next step in the press 6, which is key. * The display screen of the upper resistance control, resistance becomes active. * This grill resistance screen display control, resistance becomes active. n* Bu Lower resistance screen display control, resistance becomes active. * This turbo-resistance screen display control, resistance becomes active.
  • Page 47 * This display screen turbo fan control, the fan becomes active. The cooling fan control display screen, the active cooling fan. * This screen oven lamp control screen will activate the oven lamp. * Service not exit the screen mode unless 6 which key is pressed. noError, PTC_TOP_OpenCircuitError, PTC_TOP_ShortCircuitError,...

  • Page 48: Dealer Mode

    DisplayLCDConnectionError, MW_NTCOpenCircuitError, MW_NTCShortCircuitError, MeatProbeShortCircuitError, PTC_BOT_OpenCircuitError, PTC_BOT_ShortCircuitError, 7.1.4 Dealer Mode In order to enter fair mode, user has to enter the fair setup menu within 10seconds after the oven is energized by touching the following key combination  Lower arrow (4) ...

  • Page 49: List Of Components / Component Working Principle

    8. LIST OF COMPONENTS / COMPONENT WORKING PRINCIPLE 8.1 Technical specifications of the components; Components Power Bottom Resistance 1200 W Turbo Resistance 1800 W Top Resistance / static 1100 W Gril resistance 2200 W Gril + top resistance (1100+1100) 2200 W Turbo motor 22-26 W Lamp...
  • Page 50 1. PTC (Temperature Sensor) socket 2. Door switch socket 3. Display connection socket 4. Safety Relay (heaters neutral connection switches) 5. Low-power components (fan, lamp, chicken roasting engine) connection socket 6. Card SMPS circuit (12V: 5V Relay for riding: for the processor and screen supply) 7.
  • Page 51 Turbo and multifunctional oven is defrosting works alone. Turbo working positions with resistance, heat resistance turbo fan properly into the oven via the corporate network. Thermal circuit breaker The purpose of the thermal breaker oven thermostat on a heater of a short circuit or a short circuit as a result of any case of continuous operation without exceeding a specific value in the temperature of the oven...

  • Page 52: Fault/Error Codes

    9.FAULT/ERROR CODES 9.1 Hardware Errors Sensitivity: Public...

  • Page 53: Hardware Errors-2

    9.2 Hardware Errors-2 Sensitivity: Public...

  • Page 54: On/Off Alarm,Lampand Start/Stop Button Errors

    9.3 ON/OFF alarm,lampand Start/stop button errors Sensitivity: Public...

  • Page 55: Touch Control Errors

    9.4 Touch Control Errors Sensitivity: Public...

  • Page 56: Pt 500 Errors-1

    9.5 PT 500 Errors-1 Sensitivity: Public...

  • Page 57: Pt 500 Errors-2

    9.6 PT 500 Errors-2 Sensitivity: Public...

  • Page 58: Display Errors

    9.7 Display Errors Sensitivity: Public...

  • Page 59: Door Switchi Errors

    9.8 Door Switchi Errors Sensitivity: Public...

  • Page 60: Oven Lamp Errors

    9.9 Oven Lamp Errors Sensitivity: Public...

  • Page 61: Top Resistance Errors

    9.10 Top resistance Errors Sensitivity: Public...

  • Page 62: Bottom Resistance Errors

    9.11 Bottom resistance errors Sensitivity: Public...

  • Page 63: Top Internal Resistance Error

    9.12 Top Internal resistance error Sensitivity: Public...

  • Page 64: Turbo Resistance Errors

    9.13 Turbo resistance Errors Sensitivity: Public...

  • Page 65: Venti̇lation 1 St Level Engi̇ne Failure

    9.14 Ventilatıon 1st level engine faılure Sensitivity: Public...

  • Page 66: Pyro Oven Vent Engine Failure In 2Nd Stage

    9.15 Pyro oven vent engine failure in 2nd stage Sensitivity: Public...

  • Page 67: Turbo Motor Errors

    9.16 Turbo motor Errors Sensitivity: Public...

  • Page 68: The Rotisserie Motor Fault

    9.17 The rotisserie motor fault Sensitivity: Public...

  • Page 69: The Internal Temparature Of The Oven

    9.18 The internal temparature of the oven Sensitivity: Public...

  • Page 70: Pyro Products To The Masses Door Lock Errors

    9.19.Pyro products to the masses door lock errors(door swıtch or lock mechanism-1 Sensitivity: Public...

  • Page 71: Pyro Products To The Masses Door Lock Errors

    9.20 Pyro products to the masses door lock errors(door swıtch or lock mechanism-2 Sensitivity: Public...

  • Page 72: Pyro Product To The Masses Error Door Lock(Lock Thermostat)

    9.21 Pyro product to the masses error door lock(lock thermostat) Sensitivity: Public...

  • Page 73: Resistance Faults

    10.2.Resistance Faults 10.2.1 Resistance does not work;the food is not cooked Sensitivity: Public...

  • Page 74: Lamp Fault

    10.3 Lamp Fault 10.3.1 Furnace is working but the oven does not illuminate Sensitivity: Public...

  • Page 75: Oven Does Not Work,Oven Lamp Does Not Light

    10.3.2 Oven does not work,oven lamp does not light, Sensitivity: Public...

  • Page 76: Termostat Fault

    10.4 Termostat Fault 10.4.1 Furnace runs continuosly,the thermostat is not tripped. Sensitivity: Public...

  • Page 77: Therminal Fault

    10.8 Therminal Fault 10.8.1There is no power from the terminal does not diffuse into the electric furnace Sensitivity: Public...

  • Page 78: When The Fuse Blows The Oven Is Plugged Into The Wall Socket

    10.8.2 When the fuse blows the oven is plugged into the Wall socket. Sensitivity: Public...
  • Page 79 11.11 Measurements to be done to find the fault components Components Power Lower resistance 1200 W Turbo resistance 1800 W Top resistance / static 1100 W Gril resistance 2200 W Gril + top resistance (1100+1100) 2200 W Turbo motor 22-26 W Lamp 15-25 W Current and power drawn by components on the product with the instrument called a...
  • Page 80 Multimeter display shows a value that appear in the running resistance. Resistance wires çıkarılır.Ölçü tool probes (terminators) terminals of the contact resistance carried out. Sensitivity: Public...

  • Page 81: Component Assembly / Disassembly Be Used In Equipment

    10. COMPONENT ASSEMBLY / DISASSEMBLY BE USED IN EQUIPMENT Lokma ( 6’lık / 9’luk) Screwdrivers needlenose 2 lik alyen anahtar ucu Nippers Sensitivity: Public...

  • Page 82: Component Assembly / Di̇sassembly

    11.COMPONENT ASSEMBLY / DİSASSEMBLY NOTE: The following components disassembly operations in reverse order.Component Apply installations. 11.1 Removing the panel Before removing the board of the top of the wall must be dismantled. With the help of screwdriver, remove the screws of the top wall connection. 82 | TR Sensitivity: Public...
  • Page 83 All cables connected to the card back panel Pull the plug. Panels with 2 screws depends on the front profile. 83 | TR Sensitivity: Public...

  • Page 84: Replacing The Motherboard

    Panel to remove the side panel consists of 2 uprights with upwards of removing notch notch You can change the idle along with a new one. 11.2 Replacing the motherboard Pull the plug on the card they are attached to cables. 84 | TR Sensitivity: Public...

  • Page 85: Changing The Clock Display

    The main board is connected to the side wall 3 screws. 11.3 Changing the Clock Display Clock display card socket bulunur.kart connected on the back of the panels Remove the pull card. 85 | TR...
  • Page 86 Card board is connected with 2 screws. 86 | TR...

  • Page 87: Changing The

    Remove the screws with the help of a screwdriver. Get the idle display card and card holder plastic. 11.4 Changing the front cover Open the front cover. 87 | TR...
  • Page 88 Open the clips by pressing downwards as seen in the picture on the right and left front door hinge slot. 88 | TR...

  • Page 89: Replacing The Front Door Hinge

    Turn the front door half open position. Wasted the curator of the handle and the left hinge cover to pull upwards. Note: Remember to close the clips on the cover attaching the hinge slots in the cover will not close unless otherwise indicated. 11.1 Replacing the front door hinge 89 | TR...

  • Page 90: Changi̇ng The Removable Glass Cover 3

    2 Remove the front cover with the screws with a screwdriver after removal of the side of the hinges. After removing the screws on the hinges to pull the empty slot and change with a new hinge. 11.2 Changing the removable glass cover 3 Remove the top decor, located on the lid first.
  • Page 91 Pull yourself to remove the front door inner glass. 3. Get in the middle of the glass remaining in pulling yourself. After removing the screws pull as seen in the picture below. 91 | TR...
  • Page 92 Remove the vent cover on the side of the decor with the help of glass removal shovel can vary with a new one. 92 | TR...

  • Page 93: Changing The Handle

    Fixing the glass front door lock that can change the past, the hair removing the sheet with a new one. 11.8 Changing The Handle To do this, first remove the front cover. 93 | TR...
  • Page 94 Remove the screws of the handle with allen wrench as shown in the figure by 2. Pull out the handle grip pins down the drain. 94 | TR...

  • Page 95: Changing The Upper Wall

    This can change the blade remains in the grip handle. 11.9 Changing the upper wall 10 connects the upper wall of the oven chassis screws with a screwdriver by lifting up the wall remove. 95 | TR...

  • Page 96: Bi-Metal Thermostat Replacement

    11.10 Bi-metal thermostat replacement Remaining at the rear of the oven bimetal thermostat 2 screws with a screwdriver remove replace the thermostat with a new one. 96 | TR...

  • Page 97: Changing The Engine Cooling

    11.11 Changing the engine cooling At the top of the chassis cooling (ventilation) keep the engine clockwise to remove and replace the engine. 97 | TR...

  • Page 98: Changing The Ventilation Plate

    11.12 Changing the ventilation plate Removing the top wall of the first furnace is required for this process. And ventilation inside the chassis plate on the ceiling with the help of screwdriver to remove the 2 screws holding. 98 | TR...

  • Page 99: Air-Conditioning Thermostat Replacement

    Part of the ground in the night of the ventilation plate can be freeing. 11.13 Air-conditioning thermostat replacement Remove the top of the wall before replacing the thermostat ventilation. Ventilation ventilation flue thermostat is mounted with 2 screws 99 | TR...

  • Page 100: Removing The Rear Wall

    By removing the air conditioning thermostat, replace the screws. 11.14 Removing the rear wall Connecting the rear wall of the oven, remove the 8 screws shown in the picture. 100 | TR...
  • Page 101 Since the drop-down will position the rear wall of the oven. 101 | TR...
  • Page 102 Since the notch marked in the picture by removing the lid can open position. In 7 Remove the two screws connecting the side walls and the side wall of the oven take over. 102 | TR...

  • Page 103: Removing The Side Decor

    11.15 Removing the Side decor To remove the right and left side of the oven decorations Remove the side walls. Then remove profiles with 3 screws. Replace tabs by removing profiles. 11.16 Chaning the bottom of the base plate 103 | TR...
  • Page 104 The sides and bottom of the sump in the bottom of the oven floor to remove a total of 10 screws. Remove the bottom of the base plate to ground, as shown in the parts of the picture. 104 | TR...

  • Page 105: Chaning The Switch

    11.17 Chaning the switch Switch in order to remove the top of the wall to be removed. Remove the screw that secures the side wall switch. Then the last part of the side wall Remove the switch. 105 | TR...
  • Page 106 Remove the upper left side of the switch is down the drain and replace it in the oven. Switch picture 106 | TR...

  • Page 107: Catalytic Removal Of The Inner Side Wall

    11.18 Catalytic removal of the inner side wall. 107 | TR...

  • Page 108: Changing The Grid Resistance

    To change the internal side wall in front of Catalytic wire rack wire rack to get take.Tel shelves and wire racks bolts from the slot from the recover. Loose change with new catalytic side wall of the wall onto wire rack. 11.19 Changing the grid resistance For this operation, the oven before you unscrew the top and back walls.
  • Page 109 Remove the power cord, respectively Resistance Grid resistance furnace connects to the chassis 2 Remove the screws with a screwdriver. Open the front cover and ground grid resistance 2 Remove the screw that connects to the wall. 109 | TR...

  • Page 110: Changing The Oven Heating

    Front grill idle resistance (through chassis) çıkartın.dah then a new scheme based on the electrical resistance of the terminals plug and close the rear wall. 11.20 Changing the oven heating For this operation, undo the rear wall of the oven before. then; Remove electrical cords, respectively, of the lower resistance.
  • Page 111 Resistor connection Unscrew the screws with a screwdriver. Resistor connection Remove the screws with a screwdriver. 111 | TR...

  • Page 112: Replacing Turbo Resistance

    Structure with sliding toward you pull the oven bottom heating elements. 11.21 Replacing Turbo resistance For this operation, the oven before you unscrew the top and back walls. then; 112 | TR...
  • Page 113 Remove the cables respectively Turbo resistance. Two screws and remove the fan guard hair. Turbo resistor that connects to the chassis by removing the two screws, remove the turbo drain resistance. 113 | TR...

  • Page 114: Replace Seal Oven Changed

    Please resistance through the turbo oven. Then the electrical terminals of the new resistance Unscrew the cable resistance, respectively Turbo. According to the scheme of jewelry and turn off the rear wall. 11.22 Replace seal oven changed. To remove the front cover gasket Turn the oven first. Chassis with notches passed by removing the seal from the specified places of your change with the new.

  • Page 115: Replacing Turbo Engine

    11.23 Replacing turbo engine For this operation, top and rear walls of the furnace before and Remove fan guard hair. then; Disconnect the cables respectively turbo engine. 115 | TR...

  • Page 116: Changing Terminal

    Turbo fan Unscrew the nut and fan with the help of forceps taken. Turbo engine that connects to the chassis by removing 3 screws, replace the turbo engine. Then the electrical terminals according to the scheme of the new turbo engine and rear walls turn off your jewelry.
  • Page 117 Open the terminal cover. Terminal that connects to the rear wall and right in the box on the left (marked in the picture) Unscrew the screws with a screwdriver. Remove the cables in the back wall of the terminal block. 117 | TR...

  • Page 118: Replacing The Runners

    Terminals and the cable from the wall and replace it with a new scheme by removing the electrical connection structure according to your. 11.25 Replacing the runners 118 | TR...

  • Page 119: Replacing The Oven Lamp

    Located in the side walls of the furnace to get the wire rack wire rack wire rack bolts from the housing and replace it with a new wire rack. 11.26 Replacing the oven lamp Located in the oven to duylamb + glass group just to change the lamp Unscrew the glass. Located in the oven replace it with a new lamp.

  • Page 120: Karen Oven Lamp Replacement

    Hear the oven light bulb with lamp + glass behind the bakery to change your senses in the upper right side of your nails unscrew the rescue. 11.27 Karen oven lamp replacement Located on the side walls within the chassis frame, freeing you from the lamp, remove the nail and replace it with a new one.

  • Page 121: Changing Catalyst

    11.29 Changing catalyst The catalyst should be changed before the upper wall of the furnace and air conditioning of the hair must be removed. Catalyst in the oven top wall 3 of the nut and bonds; tır.b nuts as shown in the picture is located in the oven inner roof frame.

  • Page 122: Pyro Door Lock Be Replaced

    3 To change the catalyst at the top nut is removed and oven, bose resulting catalyst is replaced with new. 11.30 Pyro door lock be replaced To change the lock on the door of the oven before the upper wall must be removed. Pyro oven door lock of hair vent at the top right side of the chassis is mounted.
  • Page 123 Lock for securing said side wall as shown in the picture is a part. Read this part bose remove the lock by pulling the opposite direction. You can change it with a new door lock idle. 123 | TR...

  • Page 124: Pyro Ventilation Hair To Be Replaced

    11.31 Pyro ventilation hair to be replaced Ventilation to change the hair must be removed before the upper wall oven. Ventilation to change your hair before hair hair on the left side of the vent must remove the plastic. Ventilation hair available in plastic with a screwdriver to unscrew the 2 screws and take plastic.
  • Page 125 To ground idle ventilation hair from the front surface of the night to rescue pull the opposite direction of the arrows. 125 | TR...

  • Page 126: Pyro Cooling Of The Engine Be Replaced

    11.32 Pyro cooling of the engine be replaced. Connected to the furnace vent hair to change the engine cooling must first remove the upper wall. That connects to the engine cooling air conditioning hair 3 Unscrew the screws with a screwdriver.

  • Page 127: Cooling Of The Engine Thermostat Be Replaced

    Faulty engine with a new structure by changing your electrical contact. 11.33 Cooling of the engine thermostat be replaced To change the thermostat before you pull the upper wall. Thermostat connects to vent hair Unscrew the two screws and replace it with a new thermostat.
  • Page 129 REVİSION DATE EXPLATOIN 19.12.2012 BARBAROS GRUNDIG(better) SERVICE MANUAL $(in) $(id) $(pn)
  • Page 130 Envelope IV...

Table of Contents