Warning Messages - Sony BPU4800 Operating Instructions Manual

1)
Code Indication
D5xx01 SLOT Mx INTERFACE ERROR1, etc.
D6xx01 SLOT Mx UNMOUNT ERROR1, etc.
D7xx01 SLOT Mx MOUNT ERROR1, etc.
D80101 SLOT Mx FILE SYSTEM ERROR
E101pp PORT x COND3 BAD, STOP REC
E106pp PORT x FS STUFFED, STOP REC
E108pp PORT x WRITE FAIL, STOP REC
E10901 SLOT Mx CANNOT REC
E10App PORT x MAX LENGTH, STOP REC
E43100 INTERNAL MEMORY LACK
E43200 INTERNAL MEMORY WRONG POSITION
1) The portion in lower case letters in the above codes is one of the
following numbers.
ii: Number identifying the SHARE PLAY connector position on the
corresponding DM-156 board.
11: SHARE PLAY 1/2 (common)
91: SHARE PLAY 1
92: SHARE PLAY 2
pp: Number identifying the corresponding port.
81: HFR Data Record Port
82: Replay Port or HD Cut Out Port

Warning Messages

When one of the problems described below is detected by the
unit, a warning mark appears on the status bar of the web
menu. Operation can continue even when the warning mark
appears. When multiple errors occur simultaneously, the
number of errors is indicated to the right of the warning mark.
1)
Code Indication
0102pp REFERENCE DISTURBED IN TRANSCODING
020100 LOST LOCK
0B01pp PORT x VIDEO DATA ERROR
0B02pp PORT x VIDEO DATA ERROR IN SHARE PLAY
16xx00 SYS1-APP PARAMETER DISCORD 1, etc.
1901pp PORT x NO A1/A2 INPUT (P-x NO A1/A2)
1A01pp PORT x NO A3/A4 INPUT (P-x NO A3/A4)
1B01pp PORT x NO A5/A6 INPUT (P-x NO A5/A6)
2)
Description
Cannot use memory because cannot communicate with the
memory inserted in the unit. If this error persists after turning the
unit on again, the unit or memory may be faulty.
An error occurred when attempting to unmount memory.
The memory may not be usable. If error D7xx01 occurs every time
the power is turned on, the data must be salvaged.
An error occurred when detecting the memory.
If error D7xx01 occurs every time the power is turned on, the data
must be salvaged.
An error was detected with the file system in memory.
If the same error occurs every time the power is turned on, the
memory must be formatted. Follow the on-screen instructions to
format memory.
Recording was aborted because all the swap space to replace bad
memory cells has been consumed in the memory in use.
Recording was aborted because file system control limits have
been reached in the memory in use. Format the memory to use it
for recording.
Recording was aborted to protect existing data because an
attempt was made to overwrite data in the memory in use. Format
the memory to use it for recording.
An abnormality was detected in an unrecorded area in memory.
This memory cannot be used for recording. Format the memory to
use it for recording.
Recording stopped because the maximum recording time of the
port was reached.
Some or all of the internal memory boards are not installed.
An internal memory board was inserted in the wrong position.
B1: Transcode Port
ss: Number indicating the slot position on the corresponding MDC-20
board.
01: Slot 1
02: Slot 2
03: Slot 3
04: Slot 4
xx: Number identifying the error location. For details, refer to the
Maintenance Manual.
After a warning message appears, resolve the cause of the
warning based on the message.
For details on resolving the causes of warning messages,
refer to the Maintenance Manual.
Description
Sync reference was disrupted during transcoding.
Synchronization was lost during playback, recording, or editing.
Part of the playback video signal on the indicated port was
accompanied by noise.
Could not play correctly due to an NMI data transfer system fault.
An erroneous value was detected in CAMERA APP and SYS1
communications parameter.
Carrier cannot be detected on digital audio channel 1/channel 2
input of the displayed port.
Carrier cannot be detected on digital audio channel 3/channel 4
input of the displayed port.
Carrier cannot be detected on digital audio channel 5/channel 6
input of the displayed port.
49