Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ABB Welcome M21311P1-A
Summary of Contents for ABB Welcome M21311P1-A
- Page 1 Pos: 2 /DinA4 - Anl eitun gen Online /Inh alt/KNX/Doo rEntry /832 20-AP- xxx/Tit elblat t - 832 20-AP-xxx - ABB @ 1 9\m od_ 132 3249 806 476 _15. docx @ 11 108 4 @ @ 1 — VER: 1.1 | 02.20.2017 ®...
-
Page 2: Table Of Contents
Pos: 4 /Busc h-Ja ege r (N eust rukt ur)/ Mo dul-St ruktu r/Onli ne-D oku ment ation /Inh altsve rzeich nis ( --> Fü r alle Doku men te <-- )/In haltsve rzeic hnis @ 19\ mod _13 206 490 4438 6_1 5.d ocx @ 109 653 @ @ 1 Safety ....................... 3 Intended use..................... 3 Environment ..................... 3 ABB devices ................3 Terminal description.................. 4 Front overview ................4 Terminal description ..............5 4.2.1... -
Page 3: Safety
ABB devices All packaging materials and devices from ABB bear the markings and test seals for proper disposal. Always dispose of the packing materials, electronic devices and their components via authorized collection facilities or disposal companies. -
Page 4: Terminal Description
® ABB Welcome Terminal description Front overview Fig. 1 Front overview Function Light sensor Infrared LED (total of six) Indicating LED (total of three: ring, call and door open) Speaker and microphone integration Round pushbutton *If round pushbutton with ID card reader, see Chapter 5.3 for details. -
Page 5: Terminal Description
® ABB Welcome Terminal description Fig. 2 Terminal description Functions Connector for device software update Rotary switch to set the address of outdoor station (1-9) Set feedback tone of pushbutton ON/OFF Set general call to all indoor stations in one family GC=ON, press button 1 and button 2, all indoor stations ring For details, see Chapter 5.2. -
Page 6: Lock Connected With Terminals 10 And 11
® ABB Welcome 4.2.1 Lock connected with terminals 10 and 11 Exit Exit Exit — 6 —... -
Page 7: Operation
® ABB Welcome Operation Configure functions of the first and second pushbutton Fig. 3 Addressing Functions 3->OFF, 4->OFF Call apartment 001 Call apartment 002 Guard Functions 3->OFF, 4->ON Call guard unit Call apartment 001 Light Functions 3-> ON, 4->OFF Switch on light Call apartment 001 —... - Page 8 ® ABB Welcome Functions 3->ON, 4->ON Call apartment 001 Call apartment 002 — 8 —...
-
Page 9: Configure Functions Of The General Call Button
® ABB Welcome Configure functions of the general call button Functions 2->OFF Call apartment 001, both 001 indoor stations ring. Call apartment 002, both 002 indoor stations ring. Functions 2->ON Call apartment, all four indoor stations (different addresses) ring. Call apartment, all four indoor stations (different addresses) ring. -
Page 10: Round Pushbutton With Id Card Reader
® ABB Welcome Round pushbutton with ID card reader Programming Function Command Indicating LED for door open Create admin card Swipe card 1x Green Enter settings Swipe admin card 1x Orange The system will designate the first card swiped within 60 seconds after powering up the system to be the admin card. -
Page 11: Technical Data
® ABB Welcome Technical data Designation Value Operating temperature -40 °F to +158 °F Protection (cover frame IP 54 assembled) Power supply, door opener 12 V DC, 250 mA (Lock-GND) Floating output, door opener 30 V AC or DC, 1 A... -
Page 12: Mounting And Installation
® ABB Welcome Mounting and installation Warning Electric voltage! Direct or indirect contact with live components can cause dangerous currents to flow through the body, which may result in electric shock, burns or even death. Always disconnect the main power supply prior to installation and/or disassembly. -
Page 13: General Installation Instructions
® ABB Welcome General installation instructions Terminate all branches of the wiring system via a connected bus device (e.g., indoor station, outdoor station, system device). Do not install the system controller directly next to the bell transformer or other power supplies (to avoid interference). -
Page 14: Mounting
® ABB Welcome Mounting 7.3.1 Preparation Use gloves to protect your hands from laceration. 7.3.2 Dimensions 3.90“ 1.02“ 7.3.3 Surface mounted 图 1，把后壳锁在墙上 图 2，后壳接线 图 3，把前壳与后壳盖上 7.3.4 Dismantling 7.3.5 Replace nameplate — 14 —... - Page 15 Any reproduction, disclosure to third parties or utilization of its contents - in whole or in parts - is forbidden without prior written consent of ABB Inc. © Copyright 2018 ABB. All rights reserved.