Sony HDCAM J-H1 Operation Manual page 43

Item number Item name
831
I.LINK AUDIO OUTPUT
SELECT
(available only with the
HKJ-101 i.LINK Interface
Board)
(J-H3: 29.97/25/23.98PD
system only)
901 VIDEO OUTPUT DATA
(J-H1: No item)
(J-H3: 29.97/25/23.98PD
system only)
921 ASPECT FLAG (DC)
(J-H1: 29.97 system only)
(J-H3: 29.97/23.98PD
system only)
930 CONVERTER MODE
(DC)
(J-H3: 29.97/25/23.98PD
system only)
931 LETTER BOX MODE
(DC)
(J-H3: 29.97/25/23.98PD
system only)
932 H CROP POSITION (DC)
(J-H3: 29.97/25/23.98PD
system only)
934
CROSS COLOR (DC)
(J-H3: 29.97/25/23.98PD
system only)
935
DETAIL GAIN (DC)
(J-H3: 29.97/25/23.98PD
system only)
936 LIMITER (DC)
(J-H3: 29.97/25/23.98PD
system only)
937
CRISP THRESHOLD (DC)
(J-H3: 29.97/25/23.98PD
system only)
938
LEVEL DEPEND
THRESHOLD (DC)
(J-H3: 29.97/25/23.98PD
system only)
939 H.DETAIL FREQUENCY
(DC)
(J-H3: 29.97/25/23.98PD
system only)
940 H/V RATIO (DC)
(J-H3: 29.97/25/23.98PD
system only)
Settings
Selects audio channels output from the DV connector.
CH1/2 : Outputs audio signals recorded in CH-1/2.
CH3/4: Outputs audio signals recorded in CH-3/4.
4CH: Outputs audio signals recorded in CH-1/2/3/4.
Set the number of bits of the signal output from the SD SDI connector.
10 BIT
8 BIT
Selects whether or not to attach a 16:9/Squeeze identification signal regulated by
ARIB TR-B17 on SD output down-converted while an HDCAM tape is playing.
OFF : Does not attach a 16:9/Squeeze identification signal on SD output down-
converted from HD.
ON: Attaches a 16:9/Squeeze identification signal on the SD output down-
converted from HD in Squeeze mode.
Selects mode while down-converting.
EDGE-CROP : Selects EDGE-CROP MODE.
LETTER BOX: Selects LETTER BOX MODE.
SQUEEZE: Selects SQUEEZE MODE.
When LETTER BOX is selected in CONVERTER MODE (DC), extended menu
item 930, selects the aspect ratio of the down-convert output.
16:9 : Specifies aspect ratio 16:9 for HD-SD converter output.
14:9: Specifies aspect ratio 14:9 for HD-SD converter output.
13:9: Specifies aspect ratio 13:9 for HD-SD converter output.
Adjusts H CROP (horizontal direction of the extracted portion of the image using
EDGE-CROP MODE) of the down-converted output while EDGE-CROP is
selected in CONVERTER MODE (DC), extended menu item 930.
–120 ... 0 ... 120
Adjusts CROSS COLOR of the Down Converter.
0 ... 8 ... 15
Adjusts the image enhancer of the Down Converter. Adjusts the sharpness of the
contour adjustment.
0 ... 20H ... 7FH
Adjusts the image enhancer of the Down Converter. Adjusts the maximum level
of the detail that will be added to enhance the source signal.
0 ... 20H ... 3FH
Adjusts the image enhancer of the Down Converter. Sets the amplitude level that
a small amplitude signal does not enhance.
0 to 15
Adjusts the image enhancer of the Down Converter. Adjusts the range of
brightness of the contour adjustment.
0 ... 8 ... 15
Adjusts the image enhancer of the Down Converter. Sets a center frequency of
the contour adjustment.
2.6MHZ ... 3.4MHZ ... 3.9MHZ ... 4.6MHZ
Adjusts the image enhancer of the Down Converter. Sets the direction ratio
(vertically and horizontally) of the contour adjustment.
0 ... 3 ... 7
5-13
Chapter 5 Setup Menu