Z : Set Panel Status (Bks-R1607/R1608/R3204/R3205/R3209/R3210) <Monitor Menu - Sony BKS-R3202/R3210/R3220 Installation Manual

5-4. Setting Items of the Secondary Station on Monitor S-BUS (BKDS-V3293B only)
n
In BKS-R1607/R1608/R3209/R3210 of version V1.10 and
higher, the 160 description names that are transferred from
the primary station can be registered in the range of inputs
512 x outputs 512 in the order of terminal number regard-
less of the block number. When you want to use more than
160 of the description names, transmit the names from the
primary station after dividing the description names into
several blocks.
The following operations are possible from the screen.
Look at destination from source side : [*] key
Look at source from destination side : [&] key
Return to the previous page :
Move to the next page :
MONITOR SYSTEM SETUP MENU
SOURCE
name Description
1 IN001 CAM001
3 IN003 CAM003
5 IN005 VTR005
7 IN007 VTR007
9 IN009 ONAIR01
11 IN011 ONAIR03
13 IN013 STADIO1
15 IN015 STADIO3
17 IN017 MONI001
19 IN019 IN019
21 IN021 IN021
23 IN023 IN023
25 IN025 IN025
27 IN027 IN027
29 IN029 IN029
31 IN031 IN031
Ctrl-E:MENU Ctrl-D:RETURN Right:DESTINATION Left:SOURCE
Example of Setting Screen
MONITOR SYSTEM SETUP MENU
DESTINATION
name Description
1 OUT001 DST001
3 OUT003 DST003
5 OUT005 DST005
7 OUT007 DST007
9 OUT009 OUT009
11 OUT011 OUT011
13 OUT013 OUT013
15 OUT015 OUT015
17 OUT017 OUT017
19 OUT019 OUT019
21 OUT021 OUT021
23 OUT023 OUT023
25 OUT025 OUT025
27 OUT027 OUT027
29 OUT029 OUT029
31 OUT031 OUT031
Ctrl-E:MENU Ctrl-D:RETURN Right:DESTINATION Left:SOURCE
Example of Setting Screen
5-52
[(] key
[)]
key
BKS-R3210 V1.10 STATION NUMBER 6
name Description
2 IN002 CAM002
4 IN004 CAM004
6 IN006 VTR006
8 IN008 VTR008
10 IN010 ONAIR02
12 IN012 ONAIR04
14 IN014 STADIO2
16 IN016 STADIO4
18 IN018 MONI002
20 IN020 IN020
22 IN022 IN022
24 IN024 IN024
26 IN026 IN026
28 IN028 IN028
30 IN030 IN030
32 IN032 IN032
BKS-R3210 V1.10 STATION NUMBER 6
name Description
2 OUT002 DST002
4 OUT004 DST004
6 OUT006 DST006
8 OUT008 DST008
10 OUT010 OUT010
12 OUT012 OUT012
14 OUT014 OUT014
16 OUT016 OUT016
18 OUT018 OUT018
20 OUT020 OUT020
22 OUT022 OUT022
24 OUT024 OUT024
26 OUT026 OUT026
28 OUT028 OUT028
30 OUT030 OUT030
32 OUT032 OUT032
Z : SET PANEL STATUS (BKS-R1607/R1608/
R3204/R3205/R3209/R3210)
<MONITOR MENU>
Purpose
Set the various modes of the remote control unit.
Number of sources and destinations that can be controlled
from the remote control unit, can be expanded by connect-
ing multiple mother and daughter panels. Setting the
mother and daughter panels are also performed using this
menu. (Ten mother panels can be registered at the maxi-
mum.)
The setting contents are as follows.
DISPLAY MODE
STATUS= Displays the status of the primary station
crosspoint table.
PROMPT= The pressed buttons lit immediately.
PROTECT MODE
ON AIR= Execute switching from the panel even during
the protect mode.
NORMAL= Switching is not possible during the protect
mode.
PHANTOM PROTECT
PART PROT= Execute switching on the phantom on
which protect is not set.
FULL PROT=Switching is not executed on all phantoms
when any of the phantom is set to PRO-
TECT ON.
BUTTON LINK= Switching is not executed on all
phantoms when the PROTECT button
on the panel is set to ON.
*3
PANEL MODE
STAND ALONE= Stand alone panel
MOTHER= Mother panel
DAUGHTER= Daughter panel
*1
PANEL LAYOUT
TYPE + NUM.= Selecting X-Y
DIRECT= Selecting direct
*1
LEVEL MODE
SINGLE= Selecting a single level
MULTI= Selecting multiple levels
*2
DEST SELECTION
DISABLE=The destination change from panel is
disabled.
ENABLE=The destination change from panel is enabled.
*1: Applicable to BKS-R3210 only.
*2: Applicable to BKS-R1607 only.
*3: When monitor S-BUS is used, select STAND ALONE= Stand alone
machine at all times since mother-daughter setting is not necessary.
ROUTING SWITCHER SYSTEM (E)