7.1-channel a/v receiver featuring hdmi 1080p video processing (v.1.4 with 3d, arc), 7.1 surround sound, works with iphone certification and bluetooth capability (2 pages)
PIONEER Service Manual. A subscription to, or additional copies of, Also test with plug reversed Earth PIONEER Service Manual may be obtained at a nominal (Using AC adapter ground charge from PIONEER. plug as required)
—————— IC with heat-pad 1.3 SERVICE NOTICE • Discharging For more detail, please refer to "7. DISASSEMBLY - 1. Discharging". • Notes on Ground Points Connection For more detail, please refer to "7. DISASSEMBLY - 2. Notes on Ground Points Connection". VSX-1127-K...
2. SPECIFICATIONS VSX-1127-K, VSX-1027-K Amplifier section Note Continuous average power output of 90 watts* per channel, • Specifications and the design are subject to possible min., at 8 ohms, from 20 Hz to 20 000 Hz with no more than modifications without notice, due to improvements.
Page 7
HDMI terminal ..........19-pin (Not DVI) HDMI output type..........5 V, 100 mA USB terminal ..USB2.0 High Speed (Type A) 5 V, 2.1 A iPod terminal......USB, and Video (Composite) ADAPTER PORT terminal ........5 V, 100 mA WIRELESS LAN ADAPTER terminal ....5 V, 600 mA VSX-1127-K...
VIDEO ASSY WG-B ASSY BTCNT ASSY MAIN ASSY D-MAIN ASSY IR ASSY SMPS ASSY BRG ASSY AMP7 ASSY CCG ASSY G-R ASSY G-L ASSY WG-A ASSY HP ASSY F-USB ASSY FHDMI ASSY POWER ASSY FRONT ASSY MIC ASSY FVIDEO ASSY VSX-1127-K...
Page 11
The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. LIST OF ASSEMBLIES Mark Symbol and Description VSX-1127-K/CUXE VSX-1122-K/CUXESM VSX-60/UXECB VSX-1027-K/CUXE 1..PCB TTL ASSY MAIN...
ANALOG COMPONENT Video Decoder Analog Devices "ADV7181C" 24MHz CK:27M /DT:BT656 25 MHz 36.864MHz Media Processor BRIDGE CO "DM860A" LAN PHY Gate Array ETHERNET SMCS SEIKO EPSON "LAN8700" "PE7008A" iPod SDRAM - 166 Authentication 128Mb(8Mx16) APPLE (RENESAS) FLASH ROM 64Mb(4Mx16)/90ns VSX-1127-K...
Page 19
F-USB ASSY USB(FRONT) uCOM "EMMA2LL" Nor FLASH SDRAM 22.5792MHz 24.576MHz 20 MHz 1st DSP Array DA808HS EPSON D-MAIN ASSY 008A" Other ASSY SeriFlash SDRAM - 166 TMDS DIGITAL VIDEO POWER SUPPLY BLOCK Diagram ANALOG VIDEO (DCDC,LDO) CLOCK DIGITAL AUDIO VSX-1127-K...
X3002 on the FRONT Assy? replace the FRONT Assy. Replace IC3005 or Check Reset IC (IC3005) on the FRONT Assy. replace the FRONT Assy. Replace the D-MAIN Assy. 4.4 V 4.2 V Pin 2 3 ms Pin 1 >1 ms Vout VSX-1127-K...
Page 25
+ side on the FRONT Assy? IC3001 or replace the FRONT Assy. Is there 5 MHz output from Relpace X3001, IC3001 or X3001 on the FRONT Assy? replace the FRONT Assy. Does FLT3001 have damage? Relpace the FRONT Assy. Relpace FLT3001. VSX-1127-K...
Page 26
SPEAKERS key. (IR Assy CP512 pin 2 0 -> 5 V) Replace the IR Assy. Check the MAIN Assy CP12 pin 11 Replace the IR Assy. 0 -> 5 V. Check the MAIN Assy R20 Replace Q2, Q9 or 0 -> 12 V. replace the MAIN Assy. VSX-1127-K...
Page 27
D-MAIN Assy. Check the AUDIO Assy CP12 Replace the BRG Assy. pins 1, 3 signals. Check and repair analog audio lines between IC2501 pin 31, 32 and CP12 pins 1, 3 or replace the AUDIO Assy. VSX-1127-K...
Page 28
BRG Assy. Input PCM to COAX in or OPT in, Replace the D-MAIN Assy. set Auto Surround. Is Front LR SP output sound is OK? Repair IC1801 and its peripheral circuit or replace the D-MAIN Assy. VSX-1127-K...
Page 29
Repair or replace the D-MAIN Assy. Only HDMI IN1, IN2 and IN3 Rear HDMI inputs -> Front HDMI in -> are no sound? output OK? Replace HDMI cable between FHDMI Assy and D-MAIN Assy or replace the FHDMI Assy. VSX-1127-K...
Page 30
Replace the D-MAIN Assy. No GUI Replace the D-MAIN Assy. No Replace IC903 on the D-MAIN Assy No Zone2 OSD Analog Video In -> Monitor Out? or replace the VIDEO Assy. Replace IC1007, Q1012, Q1013 or replace the VIDEO Assy. VSX-1127-K...
Page 31
Others This is just for general reference and does not including every single case. 12V Trig 12V Trig Replace the IR Assy. RS-232C RS-232C Remote control Replace the FRONT Assy. VSX-1127-K...
To detect the connected WiFi Adapter Current" (Pin 45 of IC3004) device is overload. (over 600 mA) detection [How to Enter Release Mode] During Standby mode, simultaneously press and hold the "TUNE ↓" and "MULTI-ZONE ON/OFF" keys for 5 seconds. VSX-1127-K...
Page 37
Data Input (Data Input Output 0)* Serial Clock Input /HOLD (IO3) Hold Input (Data Input Output 3)* Power Supply *1 IO0 and IO1 are used for Dual and Quad instructions *2 IO0 – IO3 are used for Quad instructions VSX-1127-K...
H O L D R E S E T times error is detected. R E S E T C L E A R ? [ ↑ ] [ENTER] [↓] R E S E T R E S E T ↓ Continued VSX-1127-K...
Page 39
CEC TEST : The function for making the HDMI output terminal to output 4 Hz square wave. If the square wave is output, the CEC line is considered to be normal. FAN TEST : The function for making the FAN to be forced to rotate. VSX-1127-K...
(3) Check that the voltage between the –30V terminal is less than 1 V, using a tester. −30V ∗ Be sure to connect the GND terminal of the tester to the chassis. ∗ If the voltage is still 1 V or higher, repeat Step (2). FRONT Assy VSX-1127-K...
Page 42
Without grounding connection, the protection circuit will be activated. After repairing, be sure to remove the ground wire before reassembling. GND wire (Be sure to disconnect the GND wire before reassembly.) Back chassis Speaker chassis Main capacitor GND MAIN Assy (SIDE B) VSX-1127-K...
Page 43
(1) Remove the five screws. (BBZ30P080FTB) • Bottom view (2) Remove the one screw. (BBZ30P080FTC) (3) Remove the three screws. (1500001206010-IL) (4) Unhook the two hooks. (5) Arrange the front panel section as shown Front panel section in the photo below. VSX-1127-K...
Page 44
(1) Remove the three screws. (BBZ30P080FTC) • Bottom view (2) Remove the four screws. (BBZ30P080FTC) G-R Assy G-L Assy (3) Cut the two binders. (4) Remove the two screws. (BBZ30P080FTC) (5) Remove the WG-A and CCG Assemblies. CCG Assy WG-A Assy VSX-1127-K...
Page 45
IR Assy (8) As shown, arrange the Heatsink section over the WG-A Assy. (9) Re-connect the four connectors. (10) Connect the two extension jig cables. WG-A Assy AMP7 Assy CP401 CN404 Extension jig cable Extension jig cable (GGD1741) (GGD1740) VSX-1127-K...
Page 46
CN901 D-MAIN Assy CN603 Note: CN1504 CN1801 CN607 Confirm that a B to B connector of BRG Assy is connected to AUDIO Assy tightly. BRG Assy CP511 CN2113 CN2110 CP512 CP513 Conversion jig Conversion jig (GGD1803) (GGD1802) AUDIO Assy VSX-1127-K...
Page 47
(See procedure [3].) WG-B Assy [4-2] MAIN Assy ×3 (1) Remove the four screws. (BBZ30P180FTC) (2) Remove the six screws. (BBZ30P080FTC) (3) Cut the four binders. ×3 (4) Remove the MAIN Assy with back chassis. IR Assy MAIN Assy VSX-1127-K...
Note: Some parts on D-MAIN and F-USB Assemblies can not be replaced due to using heat-pad connection between the board. Please refer to [1.2 NOTES ONREPLACING PARTS], when the parts listed in the table is defective, replace whole Assy. VSX-1127-K...
• Mismatching between the setting file and the specification of the A/V RECEIVER type to be loaded back • Error due to Checksum, Signature Check, and Size Check • Ejecting of USB device (during reading of the setting file) VSX-1127-K...
Page 50
Before performing the backup function, please check the unit version. If small version number of Main com (EMMA) is smaller than 157, please update to the latest version. If that is 157 or over (e.g. [1-157076014091] ), the backup function is implemented. VSX-1127-K...
3. Connect the USB Memory to the USB terminal (A type) of the front panel. [Procedure] 1. While holding down "TUNE↑" key on the front panel, press "STANDBY ON/OFF" key and moves to the UPDATE PANEL mode. 2. The updating process is as follows. VSX-1127-K...
Page 52
[PRESET→] Update Confirmation U P D A T E [PRESET←] [←] [→] Update Confirmation U P D A T E Y E S [ENTER] File searching A c c e s s i n g UPDATE FILE searching completed VSX-1127-K...
Page 53
Update time is fluctuated by contents of the update. It will take about 26 minutes at the maximum. (Actual time is from 3 minutes to 26 minutes.) Time required for updating varies, because only the programs that require updating will be updated. [Confirmation] Enter UPDATE PANEL mode and check that the programs have been updated. VSX-1127-K...
(In the case of no amount instructions, apply as you think it appropriate.) 9.1 PACKING SECTION Poly bag packing style Tape (clear) Cord AC Safety Brochure Sheet SP caution Dry cell batteries (AAA size IEC R03) VSX-60 only Label getter “L” Label getter “R” VSX-1127-K...
Page 57
11 PE, Sheet 6327040059000-IL NSP 12 Warranty Sheet See Contrast table (2) NSP 13 Label VRW1629 (2) CONTRAST TABLE VSX-1127-K/CUXE, VSX-1122-K/CUXESM, VSX-60/UXECB and VSX-1027-K/CUXE are constructed the same except for the following: VSX-1127-K VSX-1122-K VSX-60 VSX-1027-K Mark Symbol and Description...
Page 61
(2) CONTRAST TABLE VSX-1127-K/CUXE, VSX-1122-K/CUXESM, VSX-60/UXECB and VSX-1027-K/CUXE are constructed the same except for the following: VSX-1127-K VSX-1122-K VSX-60 VSX-1027-K Mark Symbol and Description /CUXE /CUXESM /UXECB /CUXE MAIN Assy 7028071711010-IL 7028071711010-IL 7028071711040-IL 7028071711010-IL VIDEO Assy 7028071712020-IL 7028071712070-IL 7028071712040-IL 7028071712070-IL...
Page 69
: Audio Signal Route (Center ch) (SBL) 20010WS-03 MAIN ASSY : Audio Signal Route (Surround Back L ch) (TU) : Audio Signal Route (Tuner L ch) (VSX-1127-K, VSX-1122-K, VSX-1027-K (BT) CN3652 : Audio Signal Route (BT L ch) : 7028071711010-IL) (VSX-60: 7028071711040-IL) VSX-1127-K...
V+1R8_HHH V+1R2_HD IC9523 V O U T V I N V S S 1 V S S 2 O N / O F F GNDD GNDD GNDD GNDD S-1172B12-E6 V+5_HD V+1R2_HD V+1R5_EM V+3R3_EM GNDD GNDD GNDD GNDD GNDD 10/10 VSX-1127-K...
Page 89
10/10 D-MAIN ASSY V+3R3_EM (VSX-1127-K: 7028071752020-IL) RTQ040P02 (VSX-1122-K: 7028071752040-IL) *Q9507 (VSX-60: 7028071752040-IL) 5 0 8 R 9 4 3 9 1 ( E F ) (VSX-1027-K: 7028071752070-IL) All 1u/10 is DCH1246-A. 1 0 k CCG1222-A is 4.7u/25. C 4 3 0 0 .
CHGND C529 100N-K R558 C543 15N-K R575 R557 330K R561 Q524 JUMPER KRC103 Q504 : Video Signal Route : Video Signal Route (Y) (Cb) C550 : Video Signal Route (Cb) VSX-60 OTHER (Cr) : Video Signal Route (Cr) 10N-K VSX-1127-K...
JUMPER JUMPER JUMPER MTZJ39B MTZJ39B MTZJ39B 2M2 (5) 2M2 (5) VSX-60 VSX1122/UK VSX922/SY,DL,FX,PW,JX VSX922/AX VSX1122/SY,DL VSX1127 JUMPER OPEN JUMPER OPEN JUMPER OPEN LUG903,904 2P LUG OPEN 2P LUG OPEN 2P LUG OPEN CX100 OPEN JE202B1T2 OPEN JE202B1T2 OPEN JE202B1T2 VSX-1127-K...
Page 103
SMPS ASSY (VSX-1127-K, VSX-1122-K, VSX-1027-K: 7028071772010-IL) (VSX-60: 7028071772040-IL) J111 OPEN J110 OPEN C128 J109 OPEN 1500P/250V L102 100M T100 TRANS ZD112 MTZJ22B C113 R112 D110 100N-K 1N4007 MAX:4.0A D111 OPEN D5.6V C116 C115 1500P/250V D5.6V 100N-K(1608) D5.6V BKT101 DGND DGND...
11.3 MAIN ASSY SIDE A CP404 MAIN ASSY RLY2 RLY3 RLY4 RLY5 GND2 W2_1 POWER TRANS POWER TRAN VSX-1127-K...
Page 111
J109 J130 W2_2 C102 C103 C101 CAUTION : REPLACE WITH SAME TYPE FUSE(S). J117 ATTENTION : UTILISER UN FUSIBLE DE RECHANGE J111 DE MEME TYPE. F33 / F34 J112 T3.15A/250V CP10 D4912 GND4 J164 POWER TRANS POWER TRANS CN801 VSX-1127-K...
Page 112
SIDE B MAIN ASSY CP17 CP19 Q9-Q13 Q2-Q6 VSX-1127-K...
11.5 IR ASSY SIDE A SIDE A CN901 CN603 CN607 IR ASSY CP513 CP512 CP511 CP510 CP501 CP503 CN501 CP18 CP16 CP12 CN404 Q523 Q519 Q511 Q524 Q508 Q521 VSX-1127-K...
Page 119
SIDE B SIDE B IR ASSY CP511 CP512 CP513 CN501 CP503 CP501 CP510 Q530 Q529 Q528 Q504 Q527 Q526 Q525 Q502 Q503 Q533 Q532 Q507 Q531 IC501 VSX-1127-K...
11.11 FHDMI and F-USB ASSYS SIDE A SIDE A CP3002 FHDMI ASSY F-USB ASSY CN8202 Q7504 IC1307 CN801 IC805 J3601 IC8202 CN9202 SIDE B SIDE B J3601 CN801 CN8202 FHDMI ASSY F-USB ASSY VSX-1127-K...
→ CN → T → CN9*** → IC → D9*** → CN9*** → IC9*** → D9*** → CN9*** LIST OF ASSEMBLIES Mark Symbol and Description VSX-1127-K/CUXE VSX-1122-K/CUXESM VSX-60/UXECB VSX-1027-K/CUXE 1..PCB TTL ASSY MAIN 7025HK1110020-IL 7025HK1110010-IL 7025HK1110030-IL 7025HK1109010-IL 2..MAIN ASSY 7028071711010-IL 7028071711010-IL...
Page 135
7028071773040-IL and 7028071773070-IL are constructed the same except for the following: Mark Symbol and Description 7028071773040-IL 7028071773070-IL IC2802 IC, Linear OP J121458001010-IL Not used FRONT ASSY 7028071721050-IL, 7028071721010-IL, 7028071721040-IL and 7028071721060-IL are different in part number, they consist of the same components. VSX-1127-K...
Page 136
Symbol and Description 7028071772010-IL 7028071772040-IL CN9100 Connector L108396030010-IL Not used Mark No. Description Part No. Mark No. Description Part No. RESISTORS PARTS LIST (VSX-1127-K) R 406,450,494,537 F320184710050-IL R 424,425,430,431 N113136647820-IL AUDIO ASSY R 443,487,530,573 C060047065060-IL SEMICONDUCTORS R 467,468,474,475 N113136647820-IL IC 2501...
Page 137
IC 9515 S-1172B15-E6 Q 9503,9507,9516 J543045010060-IL 3000 FL HOLDER 4320211016000-IL U 3001 MODULE,REMOCON E940349003810-IL MISCELLANEOUS JA 1801 PIN JACK (2P) G601206A0700Y-IL RESISTORS JA 1803,1804 MODULE E100216500010-IL R 3021,3022 C060R47065050-IL KN 9801 BRACKET 4010210196100-IL R 3025,3026 C060001065060-IL P 601 SW,POLY G300003500010-IL VSX-1127-K...