Sealey SB951.V5 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAfETy
1.1. ELECTRICAL SAfETy
WARNING! It is the user's responsibility to check the following:
‰
Check all electrical equipment and appliances to ensure that they are safe before using. Inspect power supply leads, plugs and
all electrical connections for wear and damage. Sealey recommend that an RCd (Residual Current device) is used with all electrical
products. You may obtain an RCd by contacting your local Sealey dealer.
If the product is used in the course of business duties, it must be maintained in a safe condition and routinely PAT (Portable
Appliance Test) tested.
electrical safety information, it is important that the following information is read and understood.
1.1.1. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply.
1.1.2. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that they are secure.
1.1.3. Important: Ensure that the voltage rating on the appliance suits the power supply to be used and that the plug is fitted with the
correct fuse - see fuse rating in these instructions.
DO NOT pull or carry the appliance by the power cable.
8
DO NOT pull the plug from the socket by the cable. Remove the plug from the socket by maintaining a firm grip on the plug.
8
DO NOT use worn or damaged cables, plugs or connectors. ensure that any faulty item is repaired or replaced immediately by a
8
qualified electrician.
1.1.4. This product is fitted with a BS1363/A 13 Amp 3 pin plug.
If the cable or plug is damaged during use, switch the electricity supply and remove from use.
Replace a damaged plug with a BS1363/A 13 Amp 3 pin plug. If in doubt contact a qualified electrician.
Class II products are wired with live (brown) and neutral (blue) only are marked with the
Class II symbol;
A) Connect the BROWN live wire to the live terminal 'L'.
B) Connect the BLUE neutral wire to the neutral terminal 'N'.
C) After wiring, check that there are no bare wires and ensure that all wires have been correctly
connected.
ensure that the cable outer sheath extends inside the cable restraint and that the restraint is tight.
DO NOT connect either wire to the earth terminal.
8
Sealey recommend that repairs are carried out by a qualified electrician.
1.2.
REGARDING DIRECT MAINS POWER USE WITH THE TRANSFORMER PLUG.
You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested a
qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. you must ensure that you:
Inspect the transformer plug, cable, and plug for wear and damage to ensure items are safe before connecting to the mains power
9
supply. If worn or damaged DO NOT use and immediately replace, or contact a qualified electrician.
Check cables are always protected against short circuit and overload.
9
IMpORTANT: Check that the voltage marked on the transformer plug is the same as the power supply to be used.
‰
Uncoil the lead from the transformer before use.
9
DO NOT attempt to pull the transformer plug from the mains socket by the lead.
8
DO NOT use any other type of transformer with the cabinet.
8
DO NOT try to open or dismantle the transformer plug or charging base.
8
DO NOT use the transformer plug to power any other electrical item.
8
DO NOT get the transformer wet, or use in wet, damp conditions (for indoor use only).
8
WARNING! NEVER substitute a standard 13 amp 3 pin plug, or any other type of plug, for the transformer plug .
‰
1.3. GENERAL SAfETy
WARNING! ensure Health & Safety, government and local authority regulations relating to the use of shot blasting are adhered to
‰
when using this equipment. Familiarise yourself with the applications, limitations and potential hazards peculiar to the cabinet.
WARNING! disconnect the cabinet from the mains power and the air supply before attempting to change accessories or carry out
‰
any servicing or maintenance.
© Jack Sealey limited
SHOT BLAST CABINET WITH GUN
640mm x 490mm x 490mm
Model no:
Wear protective Keep away from
clothing rain
Original Language Version
SB951.V5
Recommended fuse rating
3 Amp
SB951.V5 Issue 3 (HF) 25/10/18