Honeywell OneWireless XYR 6000 Quick Start Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Transmitter
  5. oneWireless XYR 6000
  6. Quick start manual
Honeywell OneWireless XYR 6000 Quick Start Manual

Honeywell OneWireless XYR 6000 Quick Start Manual

Hide thumbs Also See for OneWireless XYR 6000:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual
OneWireless
XYR 6000 Transmitters
Quick Start Guide
34-XY-25-21
Revision 12
February 2013
Honeywell Process Solutions

Advertisement

Table of Contents
loading

Related Manuals for Honeywell OneWireless XYR 6000

Summary of Contents for Honeywell OneWireless XYR 6000

  • Page 1 OneWireless XYR 6000 Transmitters Quick Start Guide 34-XY-25-21 Revision 12 February 2013 Honeywell Process Solutions...
  • Page 2 In no event is Honeywell liable to anyone for any indirect, special or consequential damages. The information and specifications in this document are subject to change without notice.
  • Page 3 Configuration, authentication and operation are covered in other documents. Honeywell does not recommend using devices for critical control where there is a single point of failure or where single points of failure result in unsafe conditions. OneWireless is targeted at open loop control, supervisory control, and controls that do not have environmental or safety consequences.
  • Page 4 For more contact details for Europe, Asia, North and South Americas, please see back page. World Wide Web Honeywell Process Solution Support Online: www.honeywellprocess.com/ Elsewhere Call your nearest Honeywell office. See back page for details. Training Classes Honeywell Automation College: http://www.automationcollege.com OneWireless XYR 6000 Transmitters Quick Start Guide...
  • Page 5 Chassis Ground: Identifies a connection to the chassis or frame of the equipment shall be bonded to Protective Earth at the source of supply in accordance with national and local electrical code requirements. continued Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 6 ACMA and RSM. This mark is equal to the CE Mark used in the European Union. N314 directly under the logo is Honeywell’s unique supplier identification number. The INMETRO (Brazil) mark means the tested and meets applicable...

  • Page 7: Table Of Contents

    Pressure models ......................... 23 Piping ................................... 23 Process connections ............................25 General piping guidelines ............................. 26 Insert probe into process ............................27 Integral probe wiring ............................. 27 Remote probe wiring ............................27 Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 8 Certification Drawings ........................ 55 EC Declaration of Conformity ..........................55 Schedule ................................56 CSA Installation Drawings ............................ 58 ATEX Control Drawings ............................81 IECEx Control Drawings ............................93 viii OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 9 Table 2-6 Conduit entry plugs and cable glands for your XYR 6000 transmitter........17 Table 2-7 Bracket Attacment ........................19 Table 2-8 Remote Seal Transmitter Mounting ..................... 20 Table 3-1 Process connections ........................25 Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 10 Figure 5-2: IS Battery Pack .......................... 50 Figure 5-3 Power Option 24V ........................51 Figure 5-4 External 24V Power Module ....................... 51 Figure 5-5 Power Supply 24 Vdc Option (DC) System Diagram ..............52 OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 11: Introduction

    Liechtenstein Bulgaria Lithuania Cyprus Malta Czech Republic Netherlands Denmark Norway Estonia Poland Finland Portugal France Romania Germany Slovakia Greece Slovenia Hungary Spain Iceland Sweden Ireland Switzerland Italy United Kingdom Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 12: Certifications And Approvals

    CSA E60079-15: 2002 CSA E61241-0: 2002 CSA E61241-1: 2002 FM 3600: 1998 FM 3610: 1999 FM 3611: 2004 FM 3615: 2006 ANSI/ ISA 12.12.02: 2003 UL 50:2003 UL 916:1998 OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 13 Universal I/O Enclosure: IP66 Standards Used: EN 60079-0 : 2006 EN 60079-1 : 2004 EN 60079-11 : 2007 EN 60079-26 : 2007 EN 61241-0 : 2006 EN 61241-1 : 2004 Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 14 Standards Used: IEC 60079-0 : 2004 IEC 60079-1 : 2003 IEC 60079-11 : 1999 IEC 60079-26 : 2007 IEC 61241-0 : 1999 IEC 61241-1 : 1999 IEC 60079-15 : 2001 OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 15 ABNT NBR IEC 60529:2009 IEC 61241-1 : 1999 IEC 61241-0 : 1999 *See individual Product manuals as defined on page iii for exact Models ** At time of Printing Certification was pending. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 16: Electrical Data

    Special precautions shall be taken to prevent the surface of the antenna of the XYR 6000 Wireless Transmitter from being electrostatically charged. Maximum Working Pressure: See individual Product manuals as defined on page iii OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 17: Radio Certifications

    Installations in France must limit EIRP to 10dBm, for operating modes utilizing frequencies in the range of 2,454 – 2,483.5MHz. Japanese Restrictions For locations in Japan the transmitter power is restricted to 12.14dBm/Mhz {(32mW (15.4 dBm)] maximum EIRP including the antenna. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 18 1. Introduction Radio Certifications OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 19: Transmitter Mounting

    STUW700 STUW701 STTW8x0 CETW6000M Note: Add 8.0 pounds (3.6 kg) to any model equipped with the stainless steel housing option (Model Selection Guide Table IV selections A3 or SH) Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 20: Dimensions

    Dimensions For Flange and Remote Seal transmitter dimensions, obtain appropriate installation drawing using Installation drawing number tables on page 16 as a guide. Figure 2-1 Temperature/DI/Multi DI/HLAI/Corrosion transmitter dimensions OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 21: Figure 2-2 Universal I/O Temperature/Di/Multi Di/Hlai/Corrosion Antenna Dimensions

    Transmitter Mounting Dimensions Figure 2-2 Universal I/O Temperature/DI/Multi DI/HLAI/Corrosion antenna dimensions Add 139,0mm/5.47 in. To these dimensions for transmitters supplied with 4 dBi Antenna option. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 22: Figure 2-3 Dp/Dhgp Pressure Transmitter Dimensions

    2. Transmitter Mounting Dimensions Figure 2-3 DP/DHGP Pressure transmitter dimensions OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 23: Figure 2-4 Dp/Dhgp Pressure Antenna Dimensions

    Transmitter Mounting Dimensions Figure 2-4 DP/DHGP Pressure antenna dimensions Add 139,0mm/5.47 in. To these dimensions for transmitters supplied with 4 dBi Antenna option. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 24: Figure 2-5 Gp/Ap Pressure Transmitter Dimensions

    2. Transmitter Mounting Dimensions Figure 2-5 GP/AP Pressure transmitter dimensions OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 25: Figure 2-6 Gp/Ap Pressure Antenna Dimensions

    Transmitter Mounting Dimensions Figure 2-6 GP/AP Pressure antenna dimensions Add 139,0mm/5.47 in. To these dimensions for transmitters supplied with 4 dBi Antenna option. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 26: Installation Drawing Number Tables

    Table 2-4 Installation Drawing Numbers for GP/AP Remote Seal Models STRW1xG, STRW9xG, STRW1xA, STRW9xA Flat Bracket Horizontal 50060131 Flat Bracket Vertical 50060132 Angle Bracket Horizontal 50060133 Angle Bracket Vertical 50060134 OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 27: Transmitter Location

    1 & 2, GP EFG; CL III, Div 1 & 2 –40 – 100ºC 50023232-001 M20 Cable Gland IP68 ----------------------------------- –40 – 212ºF –40 – 100ºC 50023212-001 ½ NPT Cable Gland IP68 ----------------------------------- –40 – 212ºF Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 28: Bracket Mounting

    Position bracket on 2-inch (50.8 mm) pipe and install “U” bolt around pipe and through holes in bracket. Secure with nuts and lockwashers provided. Figure 2-7 Common bracket orientations OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 29: Attach Transmitter To Bracket

    Smaller “U” bolt. In flush flange, extended flange and pseudo flange pressure transmitter applications, the transmitter bolts directly to the process connection (tank spud) and no bracket is required. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 30: Remote Seal Transmitter Mounting

    11 feet (3.4 meters) above the lower remote seal. Note: The combination of tank vacuum and capillary head effect should not exceed 9 psi (300 mmHg) absolute Figure 2-8 Remote Seal mounting OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 31: Rotate Transmitter Housing

    Torque Screwdriver • 1.5 mm hex key Procedure WARNING Risk of death or serious injury by explosion. Do not open transmitter enclosure when an explosive gas atmosphere is present. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 32: Display Adjustment

    Display adjustment Step Action Honeywell recommends that the transmitter be removed from service and moved to a clean area before servicing. Loosen the M3 locking set screw on the display end-cap. See item 1 in Figure 2-10. Unscrew and remove the end cap.

  • Page 33: Process Insertion

    Blow-Down Piping Piping To Low Pressure To High Pressure Side of Transmitter Side of Transmitter To Waste To Waste 21010 Figure 3-1 Typical 3-valve manifold and blow-down piping arrangement Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 34: Figure 3-2 Typical Arrangement For ½" Npt Process Connection Piping

    As a general rule there is a 56 degree C drop (100 degrees F) in the temperature of the process for every foot (305 mm) of ½ inch uninsulated piping. OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12...

  • Page 35: Process Connections

    Chemical Tee, Saddle and Sanitary process connections. Dimensions of bolt circle and serrated gasket face conform to ASME B 16.5 Dimensions of bolt circle and serrated gasket face conform to EN 1092 Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 36: General Piping Guidelines

    Be sure all the valves in the blow-down lines are closed tight after the initial blow-down procedure and each maintenance procedure after that. Mount transmitter vertically to assure best accuracy. Position the spirit balance on pressure connection surface of AP body. Figure 3-3 Flange Mounting OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 37: Insert Probe Into Process

    For terminal connections see info starting on page 55. Plug battery connector into batteries. See page 47. Close rear end cap and cable gland. Tighten M3 locking screw on the rear end cap. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 38: Hlai Models

    3-6 and Figure 3-7. Figure 3-5 HLAI connection 0-5V 0-5V 1-5V 1-5V Figure 3-6 Voltage input wiring 0-20 mA 0-20 mA 0-20 mA 4-20mA 4-20mA 4-20mA Figure 3-7 Current input wiring OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 39: Universal I/O

    Close rear end cap and cable gland. Tighten M3 locking screw on the rear end cap. To voltage/current source. See wiring diagrams for all models on pages 30 and 31. Figure 3-8 Universal I/O Connection Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 40: Wiring For Calibration - Xyr6000 Universal I/O Wiring Diagrams For Ai/Di (Model Stuw700)

    Note: any combination of the above are allowed. For example: PV1 is a DI, PV2 is 4-20mA, PV3 is 0-20mA. Or PV1 is 0-20mA, PV2 is a T/C, PV3 is 0-20mA OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 41: Wiring For Calibration - Xyr 6000 Universal I/O Wiring Diagrams For Ai/Di/Do (Model Stuw701)

    Note: any combination of the above are allowed. For example: PV1 is a DI, PV2 is 4-20mA, PV3 is DO. Or PV1 is 4-20mA, PV2 is a T/C, PV3 is DO Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 42 Jumper wires the same gauge and stranding as the switch wires are required for all switch input combinations. Switches shall be isolated from each other and from earth ground to avoid common mode noise problems. OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 43: Corrosion Models

    Correct Pipeline Position Probe can be located at any point on the pipeline but should always be immersed in the corrosive material. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 44 Installed in a Condensate Flash Tank A condensate flash tank is also a good application. OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 45 In this case it is advisable to select the electrodes to be the same material as the pump’s impeller. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 46: Probe Installation

    (fps). Stronger flow might damage probes with three finger electrodes and interfere with the reading. If the flow rate exceeds the recommendation, a different probe style may be required. OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 47: Connect Wiring

    Feed probe wiring through the cable gland and connect to terminal block. See Figure 3-9. For terminal connections see info starting on page 55. Plug battery connector into batteries. Close rear end cap and cable gland. Figure 3-9 Corrosion transmitter with remote probe Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 48: Antenna Adjustment And Mounting

    If electrostatically charged, discharge of the antenna shroud to a person or a tool could possibly ignite a surrounding hazardous atmosphere. OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 49: Elbow

    If your model has the integral straight antenna (Figure 4-2) you can adjust its position by rotating the transmitter housing. (See page 20.) Typically, pointed straight up gives best performance but your installation may vary. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 50: Remote Antenna

    If anything such as a wire or mast does come in contact with a power line, DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by calling the power company. Don’t attempt to erect antennas or towers on windy days. OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 51: Choosing A Mounting Location

    Add this length to the length of your tower or mast and then double this total for the minimum recommended safe distance. CAUTION If you are unable to maintain this safe distance, stop and get professional help. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 52: Mounting The Antenna

    Antennas are provided with a mast mounting kit consisting of a mounting bracket and two U-bolt clamps. This kit allows you to mount the antenna to masts with outside diameters (O.D.) from 1.25 inches (3.2 centimeters) to 2 inches (5.1 centimeters). Honeywell recommends that a 1.5 inch (3.8 centimeter) or larger tubing mast be used.
  • Page 53 12 inches (30 cm) be formed close to the XYR 6000. This will minimize ice and water buildup on the transmitter itself. Tighten cables by hand only; do not use tools or you could overtighten. To lightning arrestor & antenna 12”/30cm Drip loop Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 54: Directional Mounting Procedure

    Attach antenna to mast mounting bracket as shown using supplied hardware. Adjust antenna to desired tilt and lock into place using the antenna tilt adjustment nut. Figure 4-3 Directional antenna mounting OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 55: Omnidirectional Mounting Procedure

    Secure the lead-in wire to a lightning arrestor and mast ground wire to the building with stand- off insulators spaced from 4 feet (1.2 meters) to 8 feet (1.8 meters) apart. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 56 The lightning arrestor sold by Honeywell features a bulkhead N-Female connector with a rubber “O”-ring seal which can be used for mounting through an enclosure wall. The lightning arrestor can also be mounted using the included stainless steel mounting bracket.

  • Page 57: Start Up

    Risk of death or serious injury from explosion or fire. • If IS Battery Pack, Honeywell 50047517-501, has been installed in the Wireless Transmitter, the transmitter enclosure maybe opened when an explosive gas atmosphere is present. Otherwise, do not open transmitter enclosure when and explosive gas atmosphere is present.

  • Page 58: Is Battery Holder, 50025288-502

    Procedure It is the User/Installer’s responsibility to install the XYR 6000 Wireless Transmitters in accordance with national and local code requirements. IS Battery Holder, 50025288-502 Figure 5-1: Battery assembly OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 59: Battery Replacement Procedure

    (3.5 – 5.3 Lb-in). Re-connect battery connector. Honeywell recommends lubricating the end cap O-ring with a Silicone Grease such as Dow Corning #55 or equivalent before replacing the end cap. Screw the end cap back on and tighten the M3 locking screw.

  • Page 60: Is Battery Pack, 50047517-501

    3, to 0.4 to 0.6 N-M (3.5 – 5.3 Lb-in). Reconnect the Battery Pack connector Honeywell recommends lubricating the end cap threads with a silicone grease such as Dow Corning #55 or equivalent before replacing the end cap Screw the cap back on and tighten the M3 locking screw...

  • Page 61: Figure 5-3 Power Option 24V

    Start up Battery Power Option 24V Wiring Connector M3 Locking Screw Power Connector Power Module Mounting Screws Figure 5-3 Power Option 24V J2 Connector Figure 5-4 External 24V Power Module Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 62: 24 Vdc Power Supply Option (Dc) System Diagram

    5. Start up Battery Power Option 24 Vdc Power Supply Option (DC) System Diagram (Ordinary Non-Hazardous Locations) Figure 5-5 Power Supply 24 Vdc Option (DC) System Diagram OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 63: Display Sequence

    Onewireless User Interface. For more information, please reference the OW R210 Wireless Device Manager User’s Guide (OW-CC0020). See Getting Started with Honeywell OneWireless Solutions for more information. Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide...
  • Page 64 5. Start up Provisioning OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 65: Certification Installation Requirements

    Use the following drawings and accompanying notes and text for hazardous locations. Any deviation from the installation requirements could void the certification. For non-hazardous locations you can use the same drawings without the accompanying notes and text. EC Declaration of Conformity Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 66: Schedule

    6. Certification Installation Requirements Certification Drawings Schedule OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 67 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...

  • Page 68: Csa Installation Drawings

    6. Certification Installation Requirements Certification Drawings CSA Installation Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 69 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 70 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 71 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 72 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 73 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 74 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 75 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 76 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 77 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 78 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 79 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 80 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 81 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 82 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 83 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 84 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 85 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 86 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 87 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 88 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 89 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 90 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 91: Atex Control Drawings

    Certification Installation Requirements Certification Drawings ATEX Control Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 92 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 93 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 94 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 95 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 96 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 97 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 98 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 99 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 100 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 101 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 102 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...

  • Page 103: Iecex Control Drawings

    Certification Installation Requirements Certification Drawings IECEx Control Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 104 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 105 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 106 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 107 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 108 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 109 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 110 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 111 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 112 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 113 Certification Installation Requirements Certification Drawings Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 114 6. Certification Installation Requirements Certification Drawings OneWireless XYR 6000 Transmitters Quick Start Guide Revision 12 February 2013...
  • Page 115 Revision 12 OneWireless XYR 6000 Transmitters Quick Start Guide February 2013...
  • Page 116 ASIA PACIFIC EMEA NORTH AMERICA SOUTH AMERICA (TAC) Honeywell Process Solutions, Honeywell Process Solutions, Honeywell do Brasil & Cia hfs-tac- Phone: + 80012026455 or +44 Phone: 1-800-423-9883 Phone: +(55-11) 7266-1900 support@honeywell.com (0)1202645583 Or 1-800-343-0228 FAX: +(55-11) 7266-1905...

Table of Contents