Related Manuals for Husqvarna TS 250 X3
Summary of Contents for Husqvarna TS 250 X3
- Page 2 EVERY MACHINE IS THOROUGHLY TESTED BEFORE LEAVING THE FACTORY. EACH MACHINE IS SUPPLIED ITH A COPY OF THIS MANUAL. OPERATORS OF THIS EQUIPMENT MUST READ AND BE FAMILIAR ITH THE SAFETY ARNINGS. FAILURE TO OBEY ARNINGS MAY RESULT IN INJURY OR DEATH. FOLLO INSTRUC- TIONS STRICTLY TO ENSURE LONG SERVICE IN NORMAL OPERATION.
- Page 3 Symboles • • • • • • • • • • • • •...
- Page 4 • • • • • • • • • • • • • • •...
- Page 5 • • • • • • • • • ARNING HEARING HAZARD 85 dB (A) ATTENZIONE!!! 85 dB (A) ATENCION RIESGO DE DAÑO AUDITIVO 85 dB (A)
- Page 6 DUST ARNING Cutting, especially when DRY cutting, generates dust that comes from the material being cut, which frequently contains silica California Prop 65 arning: DECALS & LOCATIONS ETIQUETAS Y SU UBICACIÓN AUTOCOLLANTS ET LEURS EMPLACEMENTS...
-
Page 8: Safety First
SAFETY FIRST! ARNINGS DO’s AND DO NOT’s ARNING: FAILURE TO COMPLY ITH THESE ARNINGS AND OPERATING INSTRUCTIONS COULD RESULT IN DEATH OR SERIOUS BODILY INJURY. DO NOT USE THE BLADE. - Page 9 This saw was designed for certain applications only. DO NOT modify this saw or use for any application other than for which is it was designed. If you have any questions relative to its application, DO NOT use the saw until you have written Husqvarna Construction Products and we have advised you. Husqvarna Construction Products...
- Page 11 I N S T R U C T I O N Use only blades marked with a maximum INDICATION operating speed greater than the blade shaft INFORMATION speed. Before starting up the machine, make sure PROHIBITION you read this entire manual and are familiar ARNING with the operation of this machine.
- Page 12 IF ANY PARTS ARE MISSING OR DAMAGED, PLEASE CONTACT YOUR Husqvarna CUSTOMER SERVICE FOR INSTRUCTIONS. Tools required: Note: The water pump inlet screen must be sub- merged in order to properly pick up water. Husqvarna® • NOTE: THE MOTOR ATER PUMP OUTLET IS NOT TO BE USED AS A GENERAL PURPOSE CONVENIENCE OUTLET.
- Page 13 OPERATING PROCEDURE ARNING: Read the Operating Procedure completely before operating your tile saw. Using the Bladeshaft Lock. Take into account the working conditions from the health and safety point of view. Always pay extreme care and attention to the Rotation direction is indicated by an arrow on preparation of the machine before starting.
- Page 14 ALIGNMENT PROCEDURES ADJUSTABLE LOCKBAR DEPTH LINKING PROTECTION Husqvarna® FIGURE 3 Check the Blade in Slot Alignment Cutting Head Adjustment (See Figure 1) MANUAL THERMAL OVERLOAD section 10 Check the Parallel Alignment RECOMMENDED EXTENSION Good motor performance depends on proper voltage. Extension cords that are too long and/ or too small in wire gauge reduce the voltage to the motor under load.
- Page 15 Before performing any maintenance, AL AYS place the machine on a level surface with the motor OFF and disconnect the electrical current. Let the machine cool down!! PROFILE HEEL SET-UP AND USE Husqvarna® See Figure 1 CLEAN Husqvarna® THE MACHINE!! ATER PUMP TROUBLE-SHOOTING...
- Page 16 Stops Flowing 1. Stop Sawing 2. Disconnect Electrical Plug from Outlet 3. Remove the Pump Husqvarna® 4. Back Flush. V-Belt Tensioning with Cam Adjustment: Always set the Motor Switch to OFF and un- plug power cord before making any repairs or adjustments to your saw.
- Page 17 TILE CUTTING ACCESSORIES ANGLE GUIDE PROTRACTOR MIGHTY MITER GUIDE BULLNOSE FOLDING STAND 542 05 10-20* 542 05 10-10* 542 16 14-80* 542 05 10-30* 542 20 32-52* Parts List: Diag. Part No. Qty. Description Diag. Part No. Qty. Description (for TS250X only) RIP FENCE MIGHTY MITER GUIDE: FOLDING STAND:...
- Page 20 NOTES: NOTAS: REMARQUE :...