Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operating Manual
Advertisement
Table of Contents
Related Manuals for Sony XDCAM XDJ-1000
Summary of Contents for Sony XDCAM XDJ-1000
- Page 1 PROFESSIONAL DISC LIBRARY XDJ-1000 PROFESSIONAL DISC DRIVE XDBK-J102 INSTALLATION MANUAL 1st Edition (Revised 1) Serial No. 10001 and Higher: XDJ-1000 (SY)
- Page 2 ! 警告 このマニュアルは，サービス専用です。 お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災， 人身事故につながることがあります。 危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。 ! WARNING This manual is intended for qualifi ed service personnel only. To reduce the risk of electric shock, fi re or injury, do not perform any servicing other than that contained in the operating instructions unless you are qualifi ed to do so. Refer all servicing to qualifi...
- Page 3 When installing the installation space must be secured Laser Diode Properties in consideration of the ventilation and service operation. Wavelength: 400 to 410 nm . Do not block the ventilation slots at the inside of Emission duration: Continuous handles on the BIN panels, and vents of the fans. Laser output power: 280 mW (max.
-
Page 5: Table Of Contents
Table of Contents Manual Structure Purpose of this manual ............3 (E) Related manuals ..............3 (E) 1. Installation 1-1. Overview of Installation ..........1-1 (E) 1-1-1. Cautions before Installation ......1-1 (E) 1-1-2. Supplied Accessories ........1-2 (E) 1-2. Installation Procedure ..........1-2 (E) 1-3. -
Page 7: Manual Structure
Manual Structure Purpose of this manual This manual is the installation manual of Professional Disc Library XDJ-1000 and Professional Disc Drive XDBK-J102. This manual is intended for use by trained system and service engineers, and provides the information that is required to install (operating environment, installation space, connection information, etc.). -
Page 9: Installation
Section 1 Installation 1-1. Overview of Installation 1-1-1. Cautions before Installation The Hard Disk Drives (HDD) are installed in this unit. The HDD is a precision part. The causes such as shock, vibration and static electricity to the unit, and the conditions of temperature and humidity may damage HDD or its data. -
Page 10: Supplied Accessories
1-1-2. Supplied Accessories . Operation manual (Japanese/English/Chinese) . Installation manual (This manual) . RFID tag (30 sheets) 1-2. Installation Procedure Installation procedure of this unit is shown on the following fl owchart. Refer to each section about detail of each fl ow. The operation manual is also required to do *-marked fl... -
Page 11: Operating Conditions
Maximum 170 W 1-4-2. Recommended Power Cord To get a power cord, please contact your local Sony Sales Offi ce/Service Center. . Use the approved Power Cord (3-core mains lead)/Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable. -
Page 12: Installation Space
1-5. Installation Space When installing, the installation space must be secured in consideration of the ventilation and service operation. . Do not block the fan exhaust areas rear panel and vents provided in the handle of the BIN panel. . Leave a space around the unit for ventilation. . -
Page 13: Installation Of Xdbk-J102
1-6. Installation of XDBK-J102 4. Fix the drive mounting plate to the drive assembly with the four screws supplied with XDBK-J102. 1. Remove the four screws, then pull out the drive mount- Drive assembly ing plate. Drive mounting plate PSW3 x 6 B3 x 5 (supplied with XDBK-J102) Drive mounting plate... -
Page 14: Removal/Installation Of Shipping Screw And Shipping Bracket
1-7. Removal/Installation of Shipping 1-7-2. Removal of BIN Tray Shipping Bracket Screw and Shipping Bracket 1. Remove the two screws (PSW3 x 6) from the left side of this unit. . Do not turn on the power before removing the shipping 2. -
Page 15: Installing The Bin Tray Shipping Bracket
5. Remove the two screws, then remove the BIN shipping 1-7-3. Installing the BIN Tray Shipping bracket. Bracket 6. Push the BIN tray into this unit. 1. Remove the two screws, then remove the BIN shipping bracket. 2. Remove the two screws on the rear panel as shown in the fi... - Page 16 4. Insert the screwdriver into the hole of the upper surface 7. Attach the BIN shipping bracket with the two screws (PSW3 x 6) removed in step 2. of this unit and pull out the BIN tray while pushing the screwdriver downward.
-
Page 17: Installing The Rfid (Option)
1-8. Installing the RFID (Option) 2. Press the release lock portion to release the lock, then draw the BIN tray (BIN mounting movable portion). To read or write the RFID tag attached to the BIN, install Release lock portion the RFID (H) assembly to the unit. Tool . -
Page 18: Rack Mounting
. Nuts: 1 set and fi rm fl oor securely with bolts, etc. . Screws (RK5 x 14) : Sony Part No.: 7-682-377-04 . Ornamental washers: . Use the specifi ed rack mount rail. Sony Part No.: 2-297-913-01 The use of other rail of low strength may drop the unit . - Page 19 Attaching the inner rails Rack Mounting Procedure 2. Pull out the inner rails from the two intermediate rails. Removing the feet 3. While pressing the stopper of the inner rail in the direction of the arrow A in the fi gure, pull the inner rail Be sure to carry the unit by the two persons or more.
- Page 20 Loosely attaching the rail brackets Attach the inner rails paying attention to the direction 6. Secure the mount rail attachment with the two nuts (with washers) and two screws (B4 x 12) supplied of the stoppers shown in the fi gure. with the rail bracket.
- Page 21 11. Check that the intermediate rails attached to both sides Attaching the outer rail 9. Temporarily secure the rail bracket at four portions are parallel to each other. 12. Securely tighten the eight screws to fi x the right and (front, rear, right and left) with the eight screws and four plate nuts (small) to the position (space by 5U) of left rails which were temporarily secured to the rack in...
- Page 22 14. Draw the right and left intermediate rails to the lock 16. Slide the unit in and out from the rack about three position. times and check that the slide rails move smoothly. 15. Grasp the handles of the rack angles while holding the If they are not smoothly, demount the unit and go back unit from the bottom, insert the inner rails into the to step 7 (“Attaching the outer rails”).
-
Page 23: Connectors/Cables
When external cables are connected to the connectors of this unit, the hardware listed below (or equivalents) must be used: Panel indication Connection connector Connection cable (Sony P/N) RJ-45 8P 1000BASE-T standard conformity article STP cable is recommended (STP: Shielded Twist Pair) 1-11. -
Page 24: Setting After Installation
1-12. Setting after Installation 1-12-1. Tools . Personal computer (hereafter referred to as PC) . Network cable 1-12-2. Procedure 1. Set the IP address of this unit. (Refer to the operation manual.) 2. Connect this unit with PC via other network device (such as hub). 3. - Page 25 7. Perform the following settings as required. Network Setting: Type the IP address, subnet mask and default gateway, LinkSpeed (default: “1 Gbps Full Duplex”), and JumboFrame (default: “Off (1514)”), and then click the [Update] button and reboot Type the date and time zone, and then click the [Update] button and Date Setting: reboot Disc Registration Mode: Select whether to use RFID and disc registration method when disc BIN is...
-
Page 26: Precautions For Relocation
1-13. Precautions for Relocation When relocating this unit, perform the following procedure before relocation. 1. Press the [RELEASE] button on the front panel to release the BIN tray lock. When the lock is released, the button indicator is lit solid. 2. - Page 28 Printed in Japan Sony Corporation XDJ-1000 (SY) J, E 2012. 7 08 4-417-557-02 ©2012...