DeWalt DWE4347 Original Instructions Manual
Small angle grinders
Hide thumbs
Also See for DWE4347:
- Original instructions manual (200 pages) ,
- Service manual (6 pages) ,
- Original instructions manual (21 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt DWE4347
Summary of Contents for DeWalt DWE4347
- Page 1 DWE4347 DWE4357 DWE4369 Final Page size: A5 (148mm x 210mm)
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A DWE4357, DWE4369 Fig. B Fig. C...
- Page 4 Fig. E Fig. D Fig. F Fig. G...
-
Page 5: Technical Data
English SMALL ANGLE GRINDERS DWE4347, DWE4357, DWE4369 Congratulations! You have chosen a D WALT tool. Years of experience, thorough product development and innovation make D WALT one of the most reliable partners for professional power tool users. Technical Data DWE4347 DWE4357... -
Page 6: Definitions: Safety Guidelines
English These products also comply with Directive 2014/30/EU and c ) Keep children and bystanders away while operating 2011/65/EU. For more information, please contact D WALT at a power tool. Distractions can cause you to lose control. the following address or refer to the back of the manual. 2) Electrical safety The undersigned is responsible for compilation of the technical a ) Power tool plugs must match the outlet. -
Page 7: Additional Specific Safety Rules
English g ) If devices are provided for the connection of dust c ) Do not use accessories which are not specifically extraction and collection facilities, ensure these are designed and recommended by the tool connected and properly used. Use of dust collection manufacturer. -
Page 8: Kickback And Related Warnings
English l ) Never lay the power tool down until the accessory e ) Do not attach a saw chain woodcarving blade or has come to a complete stop. The spinning accessory toothed saw blade. Such blades create frequent kickback may grab the surface and pull the power tool out of and loss of control. -
Page 9: Using An Extension Cable
English Electrical Safety carefully re-enter the cut. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece. The electric motor has been designed for one voltage only. e ) Support panels or any oversized workpiece to Always check that the power supply corresponds to the voltage minimize the risk of wheel pinching and kickback. -
Page 10: Intended Use
English No-Volt Wear eye protection. The No-volt function stops the grinder restarting without the switch being cycled if there is a break in the power supply. E-Clutch Electronic Brake This unit is equipped with an E-Clutch (Electronic Clutch), which in the event of a stall or wheel pinch, the unit will be shut off to Date Code Position (Fig. - Page 11 English nOTE: Edge grinding and cutting can be performed with Type Mounting guard (Fig. D) 27 wheels designed and specified for this purpose; 6 mm thick CAUTION: Prior to mounting guard, ensure the screw, wheels are designed for surface grinding while thinner Type 27 lever, and spring are fitted correctly before mounting wheels need to be examined for the manufacturer's label to see the guard.
-
Page 12: Prior To Operation
English 6. To remove the wheel, depress the spindle lock button and • Be sure the inner and outer flange are mounted correctly. loosen the clamp nut. Follow the instructions given in the Grinding and Cutting Accessory Chart. Mounting Sanding Backing Pads (Fig. B, F) •... - Page 13 English For continuous operation, slide the switch toward the front of accessory. Do not touch accessories before they have cooled. The discs become very hot during use. the tool and press the forward part of the switch inward. To stop the tool while operating in continuous mode, press the rear part •...
-
Page 14: Cutting Metal
English nOTE: Allowing the tool to rest on the work surface without not designed for side pressures encountered with surface moving will damage the work piece. grinding. Wheel breakage and injury may result. 5. Remove the tool from work surface before turning tool off. CAUTION: Wheels used for edge grinding and cutting Allow the tool to stop rotating before laying it down. -
Page 15: Maintenance
English Optional Accessories The machine must always work in an upgrinding motion. Otherwise, the danger exists of it being pushed uncontrolled WARNING: Since accessories, other than those offered out of the cut. by D WALT, have not been tested with this product, use When cutting profiles and square bar, it is best to start at the of such accessories with this tool could be hazardous. - Page 16 English LED Guide The section provides a list of possible LED blink patterns, their causes and corrective solutions. The user or maintenance personnel can perform some corrective actions, and others may require the assistance of qualified D WALT technician or your dealer.
- Page 17 English Grinding and Cutting Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Flap wheel Backing flange Wire wheels Type 27 depressed centre wheel Threaded clamp nut Wire wheels with threaded nut Type 27 guard Wire wheel...
- Page 18 English Grinding and Cutting Accessory Chart (cont.) guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Diamond cutting wheels Type 1 Guard Cutting wheel Threaded clamp nut Type 27 Guard...
- Page 20 Belgique et WALT - Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be Luxembourg België Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 enduser.BE@SBDinc.com en Luxemburg 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT Tel: 70 20 15 10 www.dewalt.dk...