Sealey TA202 Quick Start Manual

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to electrical shock
instructions hazard
1. saFety
1.1. personal precautions
When using this meter, please observe all normal safety rules concerning:
9
Protection against the dangers of electric current.
Protection of the meter against misuse.
Full compliance with safety standards can only be guaranteed if used with the test leads supplied. If necessary, they must be replaced
9
with genuine Sealey leads with the same electronic ratings. Failure to do so will invalidate the warranty.
Do not use leads if damaged or if the wire is bared in any way.
8
1.2. general saFety instructions
Familiarise yourself with the applications, limitations and hazards of the meter. IF IN ANY DOUBT CONSULT A QUALIFIED
9
ELECTRICIAN.
When the meter is linked to a measurement circuit, Do not touch unused meter terminals.
9
When the scale of the value to be measured is unknown set the selector to the highest range available.
9
Before rotating the range selector to change functions, disconnect test leads from the circuit under test.
9
Warning! Never perform resistance measurements on live circuits.
‰
Always be careful when working with voltages above 60Vdc or 30Vac rms. Keep your fingers behind the probe guards while measuring.
9
When not in use, store the meter carefully in a safe, dry, childproof location. Storage temperature range -10°C to 50°C.
9
never apply voltage or current to the meter that exceeds the specified maximum.
9
The user shall ensure that test probes are correctly selected in order to prevent danger. Probes shall be selected to ensure
9
that adequate barriers guard against inadvertent hand contact with live conductors under test and that probes have minimal exposed
probe tips. Where there is a risk of the probe tip short circuiting with other live conductors under test, it is recommended that the
exposed tip length shall not exceed 4mm.
2. introDuction
extra large, hi-contrast lCd display with 36mm high digital read-out and back light. durable case and integral stand suitable for the toughest
workshop conditions. Features millisecond pulse-width function for accurate measurement of fuel injection systems. Includes auto-ranging,
data-hold and auto-power-off. Supplied with inductive coupler, test probes, thermocouple and carry-case.
Function
maximum input
700V AC, 1000V dC
V AC or V dC
mA AC/dC 400mA AC/dC
20A AC/dC (30 secs
A AC/dC
max every 15 minutes)
Frequency
250V AC/
Resistance
dC
duty Cycle
diode Test
Continuity
Temperature
RPM
dWell
Pulse Width
2.1. symbols and descriptions
.......................................................................... Continuity
Bat ...................................................................... low Battery
............................................................................diode
dATA Hold ........................................................... data Hold
Auto ................................................................. Auto Ranging
AC ............................................................ Alternating Current
dC ...................................................direct Current or Voltage
© Jack Sealey limited
Digital automotive analyser
14 Function With inDuctive coupler
ta202
Model no:
Warning!
fig.1
layout: (Refer to fig.1.)
1. large lCd display
2. Rotary switch
3. CoM, negative input jack
4. Positive (+) input for AC/dC Voltage, Current, Hz, %duty, Cycle, ohms, diode,
5. Positive (+) input jack for AC/dC µA/mA.
6. Positive (+) 20A input jack for 20A AC/dC measurements.
7. data Hold and backlight push button.
8. Relative push button.
9. RPM, dWell, Hz%, CYl, mS ± button.
10. Mode push button.
Original Language Version
Continuity, Capacitance, Temperature (°C or °F), RPM, dwell and Pulse Width.
fig.2
TA202 Issue 5 (-6) 20/09/18