Download Print this page
Sealey Siegen Tools S01000.V2 Instructions For Use

Sealey Siegen Tools S01000.V2 Instructions For Use

Auto darkening welding helmet

Advertisement

Quick Links

thank you for purchasing a sealey product. manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to
instruction
manual
1. saFetY
warning! this helmet is not suitable for use with laser welding or cuttinG or for overhead welding applications.
ensure all workshop safety rules, regulations and conditions are complied with when using welding equipment. the helmet will not offer
9
protection against misuse of workshop tools, equipment, or accessories.
maintain the helmet in good condition and protect cartridge from liquid and dirt contact. regularly replace the protective lens and
9
replace any damaged or worn parts. use genuine parts only. unauthorised parts may be dangerous and will invalidate the warranty.
ensure the front cover window is securely in place before use.
9
fit the helmet and adjust the head band so the helmet will sit as low and near to your face as possible,
9
use helmet only in temperatures ranging from -10°c to 60°c.
9
remove ill fitting clothing, remove ties, watches, rings and other loose jewellery.
9
maintain correct balance and footing.
9
ensure the floor is clear from obstructions, not slippery and wear non-slip shoes.
9
Keep children and unauthorised persons away from the working area.
9
warning! the helmet will only protect the eyes and face from radiation and sparks. it will not protect against explosive devices or
corrosive liquids.
do not use helmet for any purpose for which it is not designed.
8
do not use helmet unless you have been instructed in its use by a qualified person.
8
do not open or tamper with the shade cartridge.
8
do not get the helmet wet or use in damp or wet locations.
8
do not leave work place with helmet in lowered position, as bright light source may darken cartridge unexpectedly.
8
do not place the helmet on a hot surface.
8
do not use helmet without front cover window fitted. to do so will invalidate your warranty.
8
clean helmet (see section 5.4) and store the helmet in a safe, dry, childproof location.
9
warning! the materials of the helmet may, when coming into contact with the wearer's skin, cause an allergic reaction to
susceptible individuals.
warning! Before welding always inspect the cartridge filter to ensure that it is not damaged. to test the filter prior to welding, direct
the front of the cartridge filter to a bright light source which will cause the lens to darken. then using your hand rapidly
cover and uncover the sensor. the filter should lighten momentarily then return to a dark state.
warning! do not use the helmet if damaged or you suspect it may be faulty. (contact sealey dealer).
danger! do not use if, at any time, the face plate in the cartridge Fails to darken when exposed to a welding spark.
remove cartridge and return to your sealey stockist for checking.
continued use of the product knowing that the auto darkening feature is not FunCtioning may damage Your
9
eYes and Cause Blindness.
2.
introduCtion
i
shade 11 welding helmet. complies to Bs en 379, Bs en 175 and din standards. features automatic switching from light to dark on striking arc.
fitted with adjustable sensitivity and delay controls for switching light to dark. fitted with solar panel power supply - no batteries required. deluxe
contoured helmet with fully adjustable headband featuring front pad for added comfort. suitable for miG, tiG and arc welding.
3.
speCiFiCation
i
model no: ............................................................. s01000.V2
shade active: ..................................................................... 11
shade inactive: .................................................................... 3
Grinding function: ............................................................... no
Viewing area: .........................................................91 x 39cm
operating time: ............................................................ 0.1ms
operating temperature: .................................. -10°c to +60°c
Power: .................................................................... solar cells
Weight: ........................................................................... 470g
© Jack sealey limited
instructions for
welding helmet auto darkening shade 11
s01000.V2
model no:
Original Language Version
s01000.V2 | issue:2 (H,f) 20/11/17

Advertisement

loading

Summary of Contents for Sealey Siegen Tools S01000.V2

  • Page 1 IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
  • Page 2 ‘H’. 5.2.2. Place the front cover ‘A’ onto the front of the helmet so that the cover clips pass into the matching holes in the helmet. Press firmly on the top of the cover to engage the top clips then press firmly at the base of the cover to engage the lower clips. replaCing the outer proteCtiVe CoVer lens (Part no:s01000.01) remove the front cover as described in sections 5.1.1 and 5.1.2. Original Language Version s01000.V2 | issue:2 (H,f) 20/11/17 © Jack sealey limited...
  • Page 3 Light state Lightest dark Darkest Manufacturers Optical class. Diffusion of Variation in Number of scale no. state scale state scale identification. light class. luminence the applied transmittance standard. class. Original Language Version s01000.V2 | issue:2 (H,f) 20/11/17 © Jack sealey limited...
  • Page 4 Parts support is available for this product. to obtain parts, please email sales@sealey.co.uk or telephone 01284 757500 enVironment proteCtion recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.