KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Note: Because CONTENTS 4 to 10 are the extracts from the Operating Instructions of this model, they are subject to change without notice. Please refer to the original Operating Instructions for further information.
Page 3
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 14.2. Troubleshooting for Speakerphone 29.3. EEPROM contents 14.3. The Setting Method of JIG (Handset) 30 HOW TO REPLACE FLAT PACKAGE IC 14.4. Adjustment Standard (Handset) 30.1. Preparation 15 THINGS TO DO AFTER REPLACING IC 30.2.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 1 ABOUT LEAD FREE SOLDER (PbF: Pb free) Note: In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that contains lead.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 1.2. How to recognize that Pb Free solder is used 1.2.1. Base Unit P.C.B. Marked (Component View) Marked J104 J103 J102 J101 VDD2 TP20 TP15 BLACK LINE_DC TP19 VDD3 TP16 VDD1 (Flow Solder Side View) Note: The location of the “PbF”...
Page 6
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 1.2.2. Handset P.C.B. Marked IC11 IC10 (Component View) C124 LEDM LEDP2 LEDP1 Marked (Flow Solder Side View) Note: The location of the “PbF” mark is subject to change without notice. 1.2.3. Charger Unit P.C.B.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 2 FOR SERVICE TECHNICIANS ICs and LSIs are vulnerable to static electricity. When repairing, the following precautions will help prevent recurring malfunctions. 1. Cover the plastic parts boxes with aluminum foil and ground them.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 4 BATTERY 4.1. Battery Installation 1. Insert the batteries negative ( ) terminal first. 2. Close the handset cover. Note: · Use only rechargeable Ni-MH batteries P03P (HHR-4EPT). 4.2. Battery Charge Place the handset on the base unit for about 7 hours before initial use.
7 hours, the batteries must be replaced. Important: · Use only the Panasonic rechargeable Ni-MH batteries P03P (HHR-4EPT). If you install non-rechargeable batteries and start charging, the batteries may leak electrolyte.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 5 LOCATION OF CONTROLS 5.1. Base Unit 5.2. Handset Note: · Up to 3 menu items can be displayed at a time. To select a menu item not shown on the current page, scroll up or down by pressing the navigator key, , respectively.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6 SETTINGS Important Information General · Use only the AC adaptor included with this product. · Do not connect the AC adaptor to any AC outlet other than a standard 220 - 240 V AC outlet.
Page 13
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Note: · After connection, you must charge the batteries to make or answer calls. · Never install telephone wiring during a lightning storm. · The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.) ·...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6.2. Guide to Settings For your reference, a chart of all items which can be customised for the base unit and the handset is printed below. · When customising the base unit and the handset, the current item or setting is highlighted.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6.3. Ringer Volume 6.3.1. Base Unit 6.3.2. Handset Note: · When the ringer volume is turned off, is displayed. · Alarms will sound and the handset will ring for intercom calls and when paged even if the ringer is turned off.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6.4. Night Mode Night mode allows you to select a block of time during which the base unit and the handset will not ring for outside calls. This feature is useful for times when you do not want to be disturbed, for example, while sleeping. Night mode can be set independently for the handset and the base unit.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6.5. PIN Code 6.5.1. Base Unit For security, the base unit PIN must be entered when changing certain settings. The default PIN is “ ”. For Service Hint: *: If the current 4-digit Base Unit PIN is forgotten, follow the procedures below.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6.6. Reset 6.6.1. Base Unit Note: · The following items will be deleted or reset to their default settings: − − − − All SMS messages − − − − Caller list · The following items will be retained: −...
Page 19
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6.6.2. Handset Note: · The following items will be deleted or reset to their default settings: − − − − Redial list − − − − Voice enhancer − − − − Category names −...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6.7. Key Lock The handset can be locked so that no calls or settings can be made. Incoming calls can be answered, but all other functions are disabled while key lock is on.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6.10. Setting Call Restriction You can restrict selected handsets from dialling certain numbers. You can assign up to 6 phone numbers to be restricted, and select which handsets will be restricted. Storing area codes here will prevent the restricted handsets from dialling any phone number in that area code. If a restricted number is dialled, the call will not be connected and the restricted number will flash on the display.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 6.12. Changing the Display Language 6.13. Setting Dialling Mode (Tone/Pulse) 6.14. Changing the Recall Time Change the recall time, if necessary, depending on the requirements of your service provider or PBX.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 7 DISPLAY 7.1. Display Icons Various icons appear on the handset display to indicate the current status of the unit. 7.2. Menu Icons When in standby mode, pressing the middle soft key reveals the handset’s main menu. From here you can access various features and settings.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 7.4. Screen Saver Mode The backlight will turn off completely after 1 minute of inactivity if the handset is not on the base unit. Only essential icons and the date and time will be displayed, and they will occasionally change position in order to preserve the life of the display.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 8 OPERATIONS 8.1. Turning the Power On/Off Power on Press [ ] for about 1 second. · The display will change to the standby mode. Power off Press [ ] for about 2 seconds.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 8.4. Phonebook The phonebook allows you to make calls without having to dial manually. You can add 200 names and phone numbers to the phonebook, assign each phonebook entry to the desired category, and search for phonebook entries by name or category.
Page 28
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 8.4.3. Editing Entries in the Phonebook Phonebook entries can be edited after you have saved them. You can change the name, phone number, and category. 8.4.4. Erasing Entries from the Phonebook 8.4.5. Storing a Number from the Caller List into the Phonebook Cross Reference: Adding Entries to the Phonebook (P.26)
Page 29
Only the one touch dial assignment is erased. The corresponding phonebook entry is not erased. 8.4.8. Copying Phonebook Entries to Other Handsets Phonebook entries can be copied from the handset to the phonebook of a compatible Panasonic handset. Copying One Entry Copying All Entries Note: ·...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 8.5. Registering a Handset to a Base Unit To Register an Additional Handset to a Base Unit (Easy Registration) The included handset and base unit are preregistered. After purchasing an additional handset, register it to the base unit.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 8.5.2. Cancelling a Base Unit A handset can be registered to a maximum of 4 base units. A handset can cancel a base unit that it is registered to. This allows the handset to “forget” the base unit.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 9 SMS (Short Message Service) SMS allows you to send and receive text messages between other fixed-line and mobile phones that support compatible SMS networks and features. Important: · To use SMS features, you must: −...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 9.3. Sending a Saved Message Cross Reference: Writing and Sending a New Message (P.32) 9.4. Editing and Sending a Saved Message Cross Reference: Writing and Sending a New Message (P.32) 9.5. Erasing Saved Messages...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 9.6. Receiving a Message When an SMS message is received: - a tone is heard (if the ringer is turned off, this tone is not heard) - “ ” is displayed is displayed...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 9.10. Changing SMS Message Centre Numbers SMS message centre telephone numbers must be stored in order to send and receive SMS messages. · Consult your service provider for more information. Note: If your phone is connected to a PBX, you need to add the PBX line access number and a dialling pause to the beginning of the Message Centre 1 phone number.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 10 TROUBLESHOOTING If you still have difficulties after following the instructions in this section, disconnect the AC adaptor and turn off the handset, then reconnect the AC adaptor and turn on the handset.
Page 38
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Cross Reference: (*12) Battery Charge (P.8) (*13) Battery Replacement (P.9) (*14) Caller ID Display (P.23) (*15) Cancelling a Base Unit (P.31) (*16) Cancelling a Handset (P.30) (*17) PIN Code (P.17)
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 12.1. Check Power 12.1.1. Base Unit Is the AC Adaptor inserted into AC outlet? (Check AC Adaptor’s specification.) Cross Reference: Power Supply Circuit (P.70) 12.1.2. Handset Cross Reference: Power Supply Circuit/Reset Circuit (P.73)
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 12.7. Bell Reception 12.7.1. Base Unit 12.7.2. Handset Cross Reference: Telephone Line Interface (P.71) Check Link (P.46) HOW TO CHECK THE HANDSET SPEAKER OR RECEIVER (P.67)
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 13 TROUBLESHOOTING BY SYMPTOM (BASE UNIT AND CHARGER UNIT) If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester or not. *: Refer to Check Point (Base Unit) (P.52) 13.1.
Page 53
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Items Check Procedure Check or Point Replace Parts (H)* DTMF Generator Check 1. Connect CN1 (Telephone Socket) to DTMF tester. IC8, R39, C41, R49, C46, C47, 2. Execute the command "hookoff" and "dtmf_hi".
Page 54
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Items Check Procedure Check or Point Replace Parts Frequency Dirft Follow steps 1 to 6 of (I). IC2, IC8, R124, Confirmation 7.Confirm that the frequency drift is < ± 30kHz/ms. R125, C153, C140, C141,...
Page 55
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Items Check Procedure Check or Point Replace Parts Power RAMP Follow steps 1 to 6 of (I). IC2, IC8, R124, Confirmation 7.Confirm that Power RAMP is matching. R125, C153, C140, C141, DA1, C142,...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 13.2. The Setting Method of JIG (Base Unit) 13.2.1. Preparation 13.2.1.1. Equipment Required · DECT tester: Rohde & Schwarz, CMD 60 is recommended. · Frequency counter: it must be precise to be able to measure 1Hz (precision; ±4ppm).
13.3. Adjustment Standard (Base Unit) When connecting the Simulator Equipments for checking, please refer to below. (A) (B) (C) (D) (E) Digital Volt Meter J104 J103 J102 VDD2 VDD3 VDD1 J101 J104 J102 J103 CHARGE- TP15 VDD2 TP20 12Ω Digital TP15 BLACK Volt Meter...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 13.4. Check Point (Charger Unit) Items Check Procedure Check or Point Replace Parts Charging Check 1. Connect Charge Contact 12Ω/2W resistor between charge+ and charge-. D11, R11, R12 2. Measure and confirm voltage across the resistor is 2.85V ± 0.2V.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 14 TROUBLESHOOTING BY SYMPTOM (HANDSET) If your unit has below symptoms, follow the instructions in remedy column. Remedies depend on whether you have DECT tester or not. *: Refer to Check Point (Handset) (P.59) 14.1.
Page 60
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Items Check Procedure Check or Point Replace Parts (G)* Battery Monitor Check 1. Apply 2.25V between BATT and GND. IC1, F1, C74, C1 C3, R81, 2. Execute the command “readbatt”. R24, R73, C9 It assumes that the return value is XX.
Page 61
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Items Check Procedure Check or Point Replace Parts Frequency Drift Follow steps 1 to 3 of (J). IC1, IC3, Confirmation 4.Confirm that the frequency Drift is < ± 30kHz/ms. R127, C117, C115, C119,...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Items Check Procedure Check or Point Replace Parts (S) SP phone Audio Check 1. Link to Base which is connected to Line Simulator. IC1, IC2, C37, and Confirmation C68, C91, 2. Set line voltage to 48V and line current to 40mA.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 14.3. The Setting Method of JIG (Handset) 14.3.1. Preparation 14.3.1.1. Equipment Required · DECT tester: Rohde & Schwarz, CMD 60 is recommended. · Frequency counter: it must be precise to be able to measure 1Hz (precision; ±4ppm).
14.4. Adjustment Standard (Handset) When connecting the Simulator Equipments for checking, please refer to below. (R) (S) Oscilloscope AF Volt Meter (J) (K) (L) (M) (N)(O)(P)(Q) Oscilloscope DECT Tester CMD60 Current Probe 8Ω 150Ω Power key BATT TP16 C125 A201 R135 (R) (S) 6.3V 47uF...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 15 THINGS TO DO AFTER REPLACING IC Cautions: Since this page is common to each country, it may not apply to some models in your country. The contents below are the minimum adjustments required for operation.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 17 HOW TO CHECK THE HANDSET SPEAKER OR RECEIVER 1. Prepare the digital voltmeter, and set the selector knob to ohm meter. 2. Put the probes at the speaker terminals as shown below.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 20 CIRCUIT OPERATION (BASE UNIT) 20.1. Outline Base Unit consists of the following ICs as shown in BLOCK DIAGRAM (BASE UNIT) (P.68). · DECT BBIC (Base Band IC): IC8 − − − − Handling all the audio, signal and data processing needed in a DECT base unit −...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 20.2. Power Supply Circuit The power is supplied to the DECT BBIC, RF Module, EEPROM and Charge Contact from AC Adaptor (+6V) as shown in Fig.101. The power supply is as follows; · DECT BBIC (IC8): CN1 (+6V) →...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 20.3. Telephone Line Interface <Function> · Bell signal detection · Clip signal detection · ON/OFF hook circuit · Audio circuits · DTMF tone signal circuits Bell & Clip (: Calling Line Identification Presentation: Caller ID) signal detection: In the standby mode, Q4 is open to cut the DC loop current and decrease the ring load.
Page 81
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT ex.) Items Address Default Data New Data Remarks C-ID (FSK) sensitivity 04 6B 01 (6dB up) 02 (12dB up) When hex changes from "00" to "01"or "02", gain increases by 6dB or 12dB.
Page 84
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Items Address Default Data New Data Possible Adjusted Possible Adjusted Remarks value MAX (hex) value MIN (hex) Sending level 00 06 Adjusted value Given value (*1) Receiving level 00 07 Adjusted value Given value (*2) (*1) When adding “01”...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 28 EEPROM LAYOUT (BASE UNIT) 28.1. Scope The purpose of this section is to describe the layout of the EEPROM (IC3) for the KX-TCD300 Base Unit. The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the base unit, some are set by the user configuration, and some are set during normal use of the phone.
Page 86
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Address Initial Name Description Default value Country Type Setting 0x0025 EEP_Ps0_Ipui PS ID 0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00, 0x00,0x00,0x00,0x00, 0x00,0x00 0x006A EEP_Ps1_InUseFlag IN-Use Flag 0x00 00:Invalid / 01:Valid 0x006B EEP_Ps1_DectPsNo DECT PS No. 0xFF 00-3F:PS No. / FF:Invalid...
Page 87
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 28.3.3. Flash Time Setting Address Initial Name Description Default value Country Type Setting 0x034D EEP_FlashTime1 Calibrated loop-break time for “80 ms” 0x08 Unit: 10 ms, defaults to 80 ms 0x034E EEP_FlashTime2 Calibrated loop-break time for “90 ms”...
Page 88
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Address Initial Name Description Default value Country Type Setting 0x03B6 EEP_KpnVmwiConfig CLIP RingVmwi set configuration 0x01 Bit0:LongBellFuncOff...1=enable, 0=disable Bit1:StatusSucceed...1=enable, 0=disable Bit2-7:Unused 0x03B7 EEP_RpasMinDuration RPAS minimum duration 0x12 Unit: 10ms, Default: 180ms 0x03B8 EEP_RpasMaxDuration...
Page 89
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Address Initial Name Description Default value Country Type Setting 0x03D6 EEP_RuDtmfDurationMax RU_DTMF maximaum duration 0x07 Unit: 10ms, Default: 70ms 0x03D7 EEP_RuDtmfDurationOff RU_DTMF Off duration 0x05 Unit: 10ms, Default: 50ms 0x0CAE EEP_RuClipReqLength Length of REQ signal...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 29 EEPROM LAYOUT (HANDSET) 29.1. Scope The purpose of this section is to describe the layout of the EEPROM (IC10) for the KX-TCA130 Handset. The EEPROM contains hardware, software, and user specific parameters. Some parameters are set during production of the handset, some are set by the user when configuring the handset, and some during normal use of the phone.
Page 91
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 29.3.2. MMI Setting Address Initial Name Description Default value Country Type Setting 0x0185 EEP_FactoryLanguageSetting Selected Language for LCD 0x01 GERAM:0 ENGLISH:1 SPANISH:2 NORWEGIAN:3 FRENCH:4 ITALIAN:5 DENISH:6 DUTCH:7 SWEDISH:8 FINNISH:9 GREEK:10 TURKISH:11 HUNGARIAN:12 PORTUGUESE:13...
Page 92
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 29.3.3. MMI1 Setting Address Initial Name Description Default value Country Type Setting 0x0102 EEP_DspSdtLevel DSP Parameter SideTone2 0x00,0x0E Main:SideTone2 Main route level MictoRcv:SideTone2 MIc to Receiver level 0x0104 EEP_DspToneLevel DSP Parameter ToneLevel 0x00,0x20,0x00,0x30...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 30 HOW TO REPLACE FLAT PACKAGE IC 30.1. Preparation 30.3. Modification Procedure of Bridge · PbF (: Pb free) Solder · Soldering Iron 1. Add a small amount of solder to the bridged pins.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 32 CABINET AND ELECTRICAL PARTS LOCATION (HANDSET) Note: (*1) The rechargeable Ni-MH battery P03P (HHR-4EPT) is available through sales route of Panasonic.
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 35 TERMINAL GUIDE OF THE ICs, TRANSISTORS AND DIODES 35.1. Base Unit 35.2. Handset 35.3. Charger Unit...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 36 REPLACEMENT PARTS LIST 1. RTL (Retention Time Limited) Ref. Part No. Part Name & Description Remarks Note: PQJT10218Y CHARGE TERMINAL (R) The marking (RTL) indicates that the Retention Time is PQJT10219Y CHARGE TERMINAL (L)
Page 101
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks ERJ3GEYJ180 ECUE1H221KBQ 220P ERJ3GEYJ335 3.3M ECUV1C104KBV ERJ3GEYJ273 ECUE1H100DCQ ERJ2GEJ822 8.2K ECUE1H220JCQ ERJ3GEYJ182 1.8K ECUE1H100DCQ ERJ12YJ120 ECUV1A224KBV 0.22...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks C194 ECUV1H100DCV PCB100 PQWPCD300FXR MAIN P. C. BOARD ASS´Y (RTL) (for KX-TCD300FXS) (for C195 ECUV1H100DCV TCD300FXT) C198...
KX-TCD300FXS / KX-TCD300FXT / KX-TCA130FXS / KX-TCA130FXT 37 FOR SCHEMATIC DIAGRAM 37.1. Base Unit (SCHEMATIC DIAGRAM (BASE UNIT)) Notes: 1. DC voltage measurements are taken with voltmeter from the negative voltage line. 2. This schematic diagram may be modified at any time with the development of new technology.