Sealey YK30XF Instructions

thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE rEAd tHESE inStructionS cArEFuLLY. notE tHE SAFE oPErAtionAL rEQuirEMEntS, WArninGS & cAutionS. uSE tHE
Product corrEctLY And WitH cArE For tHE PurPoSE For WHicH it iS intEndEd. FAiLurE to do So MAY cAuSE dAMAGE And/or PErSonAL
inJurY And WiLL inVALidAtE tHE WArrAntY. KEEP tHESE inStructionS SAFE For FuturE uSE.
Read the instruction manual
1. SAFEtY
1.1 GEnErAL SAFEtY
Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.

Maintain the press in good condition (use an authorised service agent).

Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the

warranty.
Keep the press clean for best and safest performance.

Locate the press in a suitable working area for its function, keep area clean, tidy, free from unrelated materials and ensure there is

adequate lighting.
Ensure the workpiece is correctly secured before operating the press.

WArninG! Always wear approved eye or face protection when operating the press.

Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery and contain long hair.

Keep hands and body clear of the work table when operating the press.

Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip steel toe-capped shoes/boots.

Keep children and unauthorised persons away from the working area.

do not operate the press if any parts are missing as this may cause failure and/or possible personal injury.

do not use to compress springs or any other item that could disengage and cause a potential hazard.

do not stand directly in front of the loaded press and never leave a loaded press unattended.

do not use the press for any purpose other than that for which it is designed.

do not make any modifications to the press.

do not adjust or tamper with the safety valve.

do not exceed the rated capacity of the press.

do not apply off-centre loads.

do not allow the workpiece or the press plates to fall from the work table.

do not get the press wet or use in damp or wet locations or areas where there is condensation.

do not operate the press when you are tired or under the influence of alcohol, drugs or intoxicating medication.

When not in use, release pressure from the hydraulic unit and clean the press. Stand or store the anvil "V" blocks in a safe location.

WArninG! Always position the press against a wall. if the press is situated in the open workshop, it is essential that a guard be

placed at the rear of the unit. this will prevent injury to bystanders in the event of the workpiece ejecting suddenly.
WArninG! the warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that

may occur. it must be understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
dAnGEr! When assembling, lifting or moving the press, it is recommended that it is by two people.

2. introduction
Self assembly Heavy Duty floor mounted press with hydraulic unit and single acting internal return spring return actuator (ram). Constructed from
structural steel and mild steel plates, fabricated for strength. Powder coated paint finish frames and plated fixings. Supplied with a pair of
V-blocks/pressing plates, separate pump operating handle and load/pressure gauge.
3. SPEciFicAtionS
Model:................................................................ YK30XF
Floor Mounting:.......................................................... Yes
Type:................................................................. Hydraulic
Capacity:............................................................. 30tonne
Ram Stroke:......................................................... 150mm
Ram Diameter:....................................................... 80mm
*Lateral Ram Travel:.............................................. 200mm
**Maximum Height - Ram to Table:......... 1100mm approx.
**Minimum Height - Ram to Table:........... 110mm approx.
Table Aperture:..................................................... 154mm
Work Table Depth:............................................... 284mm
Work Table Width:............................................... 460mm
Overall Height:.................................................... 1908mm
Gauge Included:......................................................... Yes
Weight:................................................................. 141.5kg
*See also fig.2 for ram lateral adjustment.
**See also fig.2 for clear opening height max. and min.
© Jack Sealey Limited
INSTRUCTIONS FOR:
30tonnE HYdrAuLic PrESS FLoor
tYPE
MODEL N
Wear safety shoes Beware crushing hands
Original Language Version
YK30XF
O:
Wear eye protection
Gauge graduated in load and pressure
30
fig.1
YK30XF Issue No: 2(I) - 15/04/15