Advertisement
1.3.3 You must ensure that you:
Inspect the charger and cable for wear and damage to ensure items are safe before connecting to the mains power supply. If worn
3
or damaged DO NOT use, immediately replace, or contact a qualified electrician.
Check cables are always protected against short circuit and overload.
3
Important: Check that the voltage marked on the charger is the same as the power supply to be used.
3
DO NOT pull or carry the charger by the power lead, or pull the plug from the mains socket by the power lead.
7
DO NOT use any other type of charger.
7
DO NOT try to open or dis-assemble the charger.
7
DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).
7
1.4
BATTERY CHARGER SAFETY INSTRUCTIONS.
WARNING! DO NOT use the charger to charge any battery other than that supplied for the drill. Other types of batteries may explode!
p
All mains electrical supply safety features must be followed as described in 1.3. above.
3
Disconnect the charger from the mains power supply when not in use.
3
DO NOT operate the charger if it has been dropped, or has received a sharp knock, or is damaged. Contact an authorised service
7
agent.
DO NOT insert foreign objects or material into the hole reserved for the battery.
7
DO NOT force the battery into the charger. The battery will only fit one way to ensure correct polarity alignment.
7
DO NOT immediately charge a second battery. Consecutive charging will overheat the charger. Allow the unit to cool for 15 minutes
7
before charging the next battery.
DO NOT attempt to connect two chargers together.
7
Store the charger in the same manner as battery, see section 1.2.
3
2. INTRODUCTION & SPECIFICATION
• Electronic variable speed control, forward and reverse.
• 15 Torque settings plus ‘Drill’.
• 1 Hour charger with BS approved 3-pin plug.
Variable Speeds: . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0-600rpm
Chuck Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10mm(1/2”)
Battery Model No: . . . . . . . . . . . . . . . . . . . . . . . . . . .CB18VBP
Weight Inc. Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.8kg
Charger Part No. . . . . . . . . . . . . . . . . . . . . . . . . . . .CP1801VC
3. OPERATING INSTRUCTIONS
Note: When new, the battery will have been shipped in a low charge state. It will take longer to charge the battery initially (about 8 hours)
and several subsequent charges may also take a little longer than when the battery reaches its optimum performance.
3.1
CHARGING THE BATTERY PACK
3.1.1
To remove the battery pack from the drill, depress the two side clips on the battery.
Do not touch the metal battery terminals.
3.1.2
Place drill in carrying case and remove the battery charger.
3.1.3
Place the charger on a safe flat surface and connect to the mains.
3.1.4. The battery is designed to fit into the charger one way only. This is to ensure that the
positive (+) and negative (-) polarities correspond. Align the + and - polarity marks on the base
of the battery with the + and - marks on the charger, insert the battery and press lightly to
seat the battery firmly into the charger, as in fig.1.
WARNING! DO NOT try to force battery into the charger with crossed polarities.
3.1.5
The green charge light will come on when the battery is inserted into the charger. Press the “SET”
button to initiate charging, the red light will now illuminate.
3.1.6
When charging is complete the green light will illuminate. Remove the battery from the charger
and the green light will go out. Switch off and unplug the charger from the mains. Push the battery
into the drill base until it latches into place. The drill is now ready for use.
3.1.7
Place the charger back into the case.
Note: Attempting to recharge a battery immediately after use may result in the red charge light not coming on. In such a case allow the
battery to cool for a time and try again.
3.2
DRILLING INSTRUCTIONS. (Ensure you have read, understood and comply with all the safety instructions)
WARNING! always wear approved safety glasses when drilling.
3.2.1
Preparation
1. Open the chuck by holding the rear collar (fig 2 ‘B’) and turning the front chuck collar (fig 2 ‘A’)
See direction arrow on chuck.
2. Insert the required drill bit into the full length of the chuck and tighten.
3. Check the drill to ensure the direction switch is in the mid (lock) position.
4. Insert the battery pack into the base of the drill and latch into place.
5. The speed of the drill is controlled by the electronic variable speed switch. After moving
direction switch to ‘forward’ (or ‘reverse’) press the speed switch gently for a slow speed and progressively increase the pressure on
the switch to produce correspondingly higher speeds (try before starting to drill).
• 10mm Keyless chuck.
• Bit holder.
• Supplied in carry-case complete with accessories.
Accessories:
Drills: . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5, 2.5, 3, 4, 5, 6mm,
Screwdriver Bits: . . . . . . . . . . . . . . . . . . . . . . . .Slotted 5, 6mm,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Phillips #1, #2,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Pozi #1, #2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Magnetic Bit Holder
fig 1
fig 2
CP1801V - 1 - 060105
Advertisement
