Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Toshiba SD-R1102
Summary of Contents for Toshiba SD-R1102
-
Page 1: Installation Instructions
Storage Device Division CD-RW/DVD-ROM DRIVE SD-R1102 Installation Instructions with VOB InstantCD/DVD CyberLink PowerDVD Software VERSION 1.0 APRIL 2001... - Page 3 SD-R1102 TOSHIBA AMERICA ELECTRONIC COMPONENTS, INC. STORAGE DEVICE DIVISION 35 Hammond Irvine, CA 92618 Contents of this manual are subject to change without prior notice. © 2001 TOSHIBA AMERICA ELECTRONIC COMPONENTS, INC. All rights reserved Printed in USA P/N 460021-A0...
- Page 4 AGES TO THE SYSTEM WHICH DOES NOT HAVE ANY OVER-CURRENT PROTECTION. DO NOT disassemble or modify this Equipment. Toshiba makes no guarantee as to the reliability, safety and performance of this Equipment when unauthorized disas- sembly and/or modification have occurred, whether or not such guarantees are set forth in the specifications.
- Page 5 DO NOT use this Equipment in any system, such as medical equipment, where personal injury or property damages could result from the Equipment’s malfunction, unexpected data corruption, or data error in the reading operation. When a disc cannot be ejected for some reason, you can use the ‘emergency eject’ mechanism.
-
Page 6: Table Of Contents
Table of Contents Checking your Kit Packaging ... 1 System Requirements ... 1 Setting Jumpers ... 2 Placing CD-RW/DVD-ROM inside your computer ... 2 Connecting Cables ... 3 IDE BUS (data) Cable ... 3 Power Cable ... 4 Audio Cable ... 4 Completing Installation ... -
Page 7: Checking Your Kit Packaging
Congratulations on your purchase of a Toshiba CD-RW/DVD-ROM drive and Kit. The following information will help you in the simple installation of your new CD-RW/DVD-ROM drive. CHECKING YOUR KIT PACKAGING Please unpack your CD-RW/DVD-ROM kit, and assure that you have the follow-... -
Page 8: Setting Jumpers
The following steps must be performed to properly install your CD-RW/DVD- ROM. Set drive’s jumpers Connect audio cable Attach IDE BUS cable Connect power cable Mount CD-RW/DVD-ROM Install CyberLink PowerDVD Install VOB InstantCD/DVD software (used for recording CDs) SETTING JUMPERS The mode select jumpers are six (6) straight angle pins located on the rear of the CD-RW/DVD-ROM. -
Page 9: Connecting Cables
2. If the CD-RW/DVD-ROM is replacing a CD-ROM, disconnect all connectors and remove the CD-ROM presently installed in your system. 3. Your Toshiba CD-RW/DVD-ROM can be placed in any free half-height drive slot at the front of your computer. (It can be mounted horizontally or vertically.) 4. -
Page 10: Power Cable
Connect secondary IDE BUS cable to CD-RW/DVD-ROM drive, assuring that pin 1 of the cable (side with red stripe) is connected to pin 1 on the drive. • If the CD-RW/DVD-ROM is the only drive connected on the secondary IDE BUS cable: connect drive to the last set of pins on IDE BUS cable. -
Page 11: Completing Installation
CD-RW/DVD-ROM to tip of screw). Replace the computer cover and all outer screws. ATAPI CD/DVD Software Driver: Toshiba’s CD-RW/DVD-ROM drives do not require any unique device drivers for Windows '95/'98/2000/WinMe/NT. After installing your drive and re-booting, your system should recognize your drive. Win '95/'98/2000/WinMe/NT operating systems support all Toshiba ATAPI CD-RW, CD-ROM and DVD-ROM drives na- tively. -
Page 12: Cyberlink Powerdvd
For additional information on using this soft- ware, please refer to the PowerDVD software, click “?”). CD-RW/DVD-ROM FRONT PANEL The photo illustrates the following features of the SD-R1102 CD-RW/ DVD-ROM front panel: Headphone Jack Volume Control... -
Page 13: Specifications
Owner's Manual carefully and keep this manual for future reference. In case of any trouble with this model, please contact your nearest "Authorized Repair Center". To prevent direct exposure to the laser beam, do not try to open the enclosure SD-R1102 DVD: 2,048 2,048 (mode 1) -
Page 14: Warranty Information
WARRANTY INFORMATION Toshiba America Electronic Components, Inc. (“TAEC”) warrants that all prod- ucts will, upon delivery by TAEC to the customer in new condition, be free from defects in material and workmanship for a period of twelve (12) months after delivery. - Page 16 460018-C0 P/N 460021-A0...