Page 1
For information on the latest products and peripheral devices, refer to the following Web page. Ihttp://www.netcam.toshiba.com The above URL is subject to change without prior notice. If the URL changes, refer to the Toshiba website (http://www.cctv.toshiba.com). This User’s Guide applies to the firmware version R1.01 and later. WR01-01...
INTRODUCTION FEATURES & DESCRIPTION IK-WR01A has the following features: (1) Flush/Surface mount. (2) IP66 Standard for dust and water resistance. (3) Built in vari-focal lens with auto-iris Focal length 3.0~8.0mm. (4) Incorporated 1/3" type CCD image sensor gives high resolution and excellent sensitivity 480 lines horizontal resolution 0.4 lx minimum illumination with tint dome cover...
Page 4
INTRODUCTION (Cont.) GViewing ... 34 Viewing Images ... 34 Camera Window Screen ... 35 • Menu that is displayed when right-clicking on the image ... 35 • Adjusting Images on the Camera ... 36 Adding Images ... 38 GViewing Logs ... 39 GAbout Recording Images ...
Names and Features of Parts Mode Setting Switch BLC (Backlight Compensation Switch) With the switch on, it adjusts the backlight automatically to obtain the best possible image. Sets camera synchronization to line lock with the switch on. Available only with AC24V. Lens Iris ADJ Counterclockwise: The picture becomes darker.
Page 6
INTRODUCTION (Cont.) Video Out Jack Connect a video monitor to the video output jack. RJ45 Connector (Option) Ethernet Port Connect a LAN cable to the port. A PoE compatible hub is also supported. AC24V/DC12V Power Plug Terminal Connect an AC24V/DC12V power plug to the terminal.
Installation/Setup G Connecting to a Video Monitor G Line-Lock Control G Adjusting a Lens G Setting Up the Network Camera Environment G Connecting the Camera and Personal Computer by Network G Using the Camera Search Application “Camera Finder” G Changing Administrator Login ID and Password G Setting up Access Restriction G Configuring the Network...
INSTALLATION Connect the cable of the camera and the cable from the designated power supply with respective connectors. Screws for securing the camera and mounting base to the ceiling or wall are not supplied with the unit. Use appropriate screws. NOTE •...
Page 9
Tilt rotation Horizontal rotation Remove three silver transport protection screws. Transport Protection Screws (silver) To obtain a level image, turn the Horizontal Adjustment Ring. Turn the pan lock counterclockwise to loosen it. Adjust the pan direction of the lens. After adjustment, turn pan lock 1 clockwise to tighten it.
Page 10
INSTALLATION (Cont.) The lens tilt angle can be adjusted by loosening the tilt lock 2. After adjusting, tighten the tilt lock 2. Adjust the zoom position by loosening the zoom lock lever 3. After adjusting, tighten the zoom lock lever When installing the camera on a wall, manipulate the horizontal adjustment ring 4 to adjust the inclination of the image.
Installing the Camera Unit I Installation to Wall or Ceiling with Mounting Base (Surface Mount Installation) • When installing the camera unit on the wall, mount it with the drain groove on the downside. Do not block the drain groove. •...
INSTALLATION (Cont.) I Installation to Junction Box with Bracket (Flush Mount Installation) Screws (not supplied) Screws Mount camera base with three supplied screws B. (Shorter screw(M4x10)) Tighten and lock the screws firmly. Unit: mm (inches) 4 6 m m ( 1 . 8 1 in c h ) Junction Box 8 3 .
I Change of Dome Cover Dome replacement When the dome cover is damaged or to be replaced with a transparent cover, call your distributor or sales person. Firmly tighten three mounting screws. Take care not to let dirt or foreign object enter between the parts.
Since this camera uses 24V AC UL Listed Class 2 power supply or 12V DC power supply, it should be connected to a power supply that allows for at least 5w consumption. Because the IK-WR01A uses a mechanism, a sufficient power supply with adequate current specifications is required.
About the POWER SELECT Switch CAUTION : The IK-WR01A operates with one of the following power source: 12vDC, 24vAC or PoE. Set the power selection switch on the camera to the correct power source before turning the camera on. DO NOT RE-SET THE POWER SELECTION SWITCH WHEN THE UNIT IS ON.
Line-Lock control Matching the vertical synchronization with the power frequency is called the Line-Lock. This function is activated when the LL of Mode Setting Switch is on. When two or more cameras are switched by video switcher for viewing by a monitor TV, the vertical sync.
I LINE LOCK PHASE When a video switcher switches two or more cameras, the picture may fluctuate on the video monitor due to the different AC line phase of each camera. In this case, adjust the V PHASE controller to get a stable image. Line Lock V PHASE CONTROL NOTE The camera is synchronized to the power frequency of 60...
Adjusting a Lens Back Light Compensation By turning on the back light compensation switch, the camera controls the back light automatically to ensure proper exposure in the specified area when using an auto iris lens or fixed iris lens with the “AES” mode. For setting the metering area of back light compensation, refer to page 37.
NOTE When there is a large difference in contrast between the subject and the surrounding (e.g. when the background is extremely bright), the BLC effect may be limited. Auto White Balance (AWB) The camera has an auto white balance capability in the range of 2,500K to 10,000K color temperature of light.
Setting Up the Network Camera Environment Requirements for Network Camera Monitoring System ° Administrator’s personal computer This manual refers to a personal computer that has been granted all privileges for configuring, operating, monitoring, and other operations as the “administrator’s personal computer.”...
Connecting the Camera and Personal Computer by Network IAbout the IP Address To connect to the network, the administrator needs to set the network camera IP address. There are two options to set the IP address. • Obtaining an IP address automatically from the DHCP server •...
Connecting the Camera and Personal Computer by Network (Cont.) Structure of Connection The following are two methods of connecting the network camera: • Use a crossover cable • Connect with a hub or router G Using a crossover cable to establish a connection (example) IP address 192.168.0.30 Crossover cable is not provided with the product.
Connecting Connect a LAN cable and then turn the power on. Connect the LAN cable (straight) leading to the camera with a powered hub. Alternatively, use a LAN cable (crossover) to connect the camera with the powered personal computer. When connecting a PoE compatible hub/router, power will be provided to the camera through the LAN cable even though the power plug terminal is not connected.
G Using “Camera Finder” to Search for a Camera From the “Start” menu, point to “Programs” and “TOSHIBA Network Camera”, and then select “Camera Finder.” Start up “Camera Finder” and click “Search” button. All the cameras currently connected to the network appear.
Important Toshiba is not responsible for any damages caused by this software. The “Administrator” button in the “Camera Finder” is invalid for the IK-WR01A. When connecting to the IK-WR01A, be sure to click the “User” button. When you log in as Administrator, set up access restrictions (➝ page. 28).
Changing Administrator Login ID and Password Be sure to change the default login ID and password. You are able to change important information and settings of the camera through the Administrator Login. To have higher security, be sure to change your login ID and the password. Remember this new login ID and password.
Page 27
Enter “root” in the Current login ID field and “ikwb” in the Current Password field. Enter a new login ID in the New login ID field and a new password in the New Password field and New Password (Confirm) field. Enter the same password in the New Password field and the New Password (Confirm) field.
Setting up Access Restriction You can set up the access restriction by requiring the user to enter the user ID and password for the Administrator login or the registered user ID and password. Click “Configuration” on the left side of the “Camera Window”...
Page 29
Click the “Set/Change” button. New user ID and password for the User login are stored in the network camera. Check “ON” in the “User authorization required” section. Click the “Set” button. A screen appears, asking you to enter a user name and password. Enter the Administrator login ID and password in the field of user name and password, respectively ➝Click the “OK”...
Configuring the Network Manually You can change the settings of network connection manually. • Enter an IP address manually if you are not using, or do not want to use the DHCP server. Log in as Administrator. Click “Configuration” on the left side of the “Camera Window”...
Page 31
Select “Manually.” The default setting is “Automatically by DHCP.” Fill in “IP Address,” “Subnet Mask,” “Default Gateway,” “DNS1” and “DNS2.” Important If you do not know the subnet mask, consult the provider or network system administration support center. You do not need to enter the default gateway if the network camera will not be accessed from another network.
Viewing Viewing Images The images in the network camera can be displayed with the Internet browser on the personal computer. Search for the network camera with the “Camera Finder” ¡ Log into the camera. The browser starts up and then the Camera Window screen appears for the network camera.
ICamera Window Screen Name of camera (¡ page.57) * Cannot be operated through the User login. IMenu that is displayed when right-clicking on the image Current date and time of camera (¡ page 58) To record images (¡ page.51) To record currently displayed images (¡ page.53) Image on the camera...
Viewing (Cont.) Adjusting Images on the Camera You can set up the image quality and resolution for the images on the camera. To perform the operation, you need to log in as Administrator. When you log in as User, the operation is disabled.
Page 37
G Flickerless You can set up the function to reduce the flickering caused by lighting such as fluorescent lights. On: To activate the flicker compensation Off: Not to activate the flicker compensation (Default: Off) G Area (BLC) You can set up the target area for back light compensation (¡ page.18). Selectable settings: 1 to 5 (default: 1) G AE Level The camera adjusts the brightness of the image automatically.
Viewing (Cont.) Adding Images You can add and view images on the other camera. Enter the IP address of other camera in the “Watching:” field ¡ Click “Add.” An image on the other camera is added on the Camera Window screen. Up to 9 images can be displayed on the Camera Window screen.
Viewing Logs You can view a list of logs. To perform the operation, you need to log in as Administrator. When you log in as User, the operation is disabled. Click “View log” on the left side of the Camera Window screen.
Recording G About Recording Images G Recording Images on FTP Server G Recording Images on a Personal Computer...
Page 42
About Recording Images Network camera can record images according to your need. Recordable media and its recordable contents are as follows. Recordable Media FTP Server Personal Computer Recordable Contents Data of “Periodic FTP by Schedule” Data of “Motion Detection” Image data recorded by “Image Recording” (JPEG) (➝...
Recording Images on FTP Server By using FTP server, it becomes possible to manage periodic transferring and saving of huge amounts of recorded image data. The recordable images on an FTP server include “Periodic Recording Data by Schedule” or “Recording by FTP by Motion Detection”. Record Settings Click “Configuration”...
Recording Images on FTP Server (Cont.) Configure each setting items. I FTP General Settings You can control the settings to connect to an FTP server. GFTP sever: Select either one of them below and enter correct information. Server Name • IP Address •...
Page 45
NOTE • When selecting “Periodic”, network camera logs in to FTP server automatically a minute before the scheduled recording starts. When the scheduled recording stops, there may be some unsent image data left in the camera. The camera will not log out from the FTP server until all images have been transferred.
Recording Images on FTP Server (Cont.) IPeriodic FTP by Schedule You can control the settings to record images for Periodic FTP by Schedule. To run the recording, select “Periodic” in “Connection to FTP Enable” (➝ page. 43). 1) Configure recording schedule Select one of the setting items for each day of a week.
Page 47
NOTE • The cycle may shift depending of Resolution (image size) and networking conditions. 4) Enter “File Name” Select one of two patterns, enter characters in the part described as (keyword). File name will be shown like this: e.g. Pattern1: (keyword) yy mm dd HH MM SS 00.JPG Pattern2: LV (keyword) yyyy mm dd HH MM SS ***N.JPG NOTE •...
Recording Images on FTP Server (Cont.) IFTP by Motion Detection You can control the settings to record images for FTP by Motion Detection. To configure the motion detection, select “Enable” in or “Motion Detect” in the alarm settings (➝ page. 64) To run the recording, select “Motion Detection”...
Page 49
4) Enter “File Name” Enter characters in the part described as (keyword). File name will be shown like this: e.g. MD (keyword) yyyy mm dd HH MM SS ***N--A.JPG NOTE • You cannot use these characters: \ / : ; , ” | ? * < > Followings are the meaning of each part.
Recording Images on FTP Server (Cont.) File Transfer Order • Basically, files are transferred in recorded order. However, files may not be transferred depending on the conditions of networking or FTP server. (The camera will not backup data.) NOTE • Depending on the conditions of networking and the FTP server, there may be occasions when files will not transfer.
Recording Images on a Personal Computer You can record images in the JPEG file or AVI file format on a personal computer. Image Recording Feature Right-click on the image of the “Camera Window” screen. The operating menu appears on the screen. Click “Image Recording.”...
Page 52
Recording Images on a Personal Computer (Cont.) Click the “Start” button. The recording operation starts. To stop the recording, right-click on the image ¡ Click “Stop Image Recording” in the displayed operating menu. Mark here to save images as an AVI file. Mark “Auto”...
Recording Current Image Data as Still Image Right-click on the image of the “Camera Window” screen. The operating menu appears on the screen. Click “Save Current Picture As.” A screen appears, asking you to specify the destination folder and file name. Specify the destination folder and file name.
Setting up G How to Set up G System Settings G User Settings G Admin Settings G Alarm Settings G Network Settings G Mail Settings G FTP Client Settings G DDNS Settings G Updating the Firmware G Saving the Settings on a Personal Computer...
How to Set up Only the Administrator is authorized to set up configurations for the network camera. You can select the setup items by clicking “Configuration” on the “Camera Window” screen. General Configuration Click “Configuration” on the left side of the “Camera Window”...
Page 57
System Settings You can change a camera name and control time set. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “System” on the left side of the screen. •...
IRebooting the network camera You can restart the network camera. 1) Click “Reboot IP Camera.” A confirmation message appears, asking whether or not the camera should be rebooted. 2) Click “OK.” IUpdating the Firmware You can update the firmware on the network camera. Click “Firmware update.”...
User Settings You can set up access rights. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “User” on the left side of the screen. •...
Page 61
G Storing the user name and password 1) Enter the user name, password and password (confirm) for a new user in the field of “User ID,” “Password” and “Confirm,” respectively in “Add a user or change password.” 2) Click the “Set/Change” button. •...
Page 62
Admin Settings You can change the Administrator ID and password. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “Admin” on the left side of the screen. •...
Page 63
Configure each item. G Changing the Administrator ID and password 1) Enter the current login ID and the current password in “Current Login ID” and “Current Password,” respectively. 2) Enter new login ID, new password and new password (confirm) in “New Login ID,”...
Alarm Settings You can configure the motion detection. If you set the function of the “Motion Detect” to “Enable”, an alarm will notify you when a change is detected. Click “Configuration” on the left side of the “Camera Window” screen. •...
Setting the motion detection. G Setting the motion detection 1) Select one of the followings in “Motion Detect:” Enable : To turn motion detection on. Disable : To turn motion detection off. (Default: Disable) 2) Select the “Sensitivity” level from the pull-down menu. High : Generates an alarm upon detection even to the slightest change in brightness.
Network Settings You can configure an IP address for network connection. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “Network” on the left side of the screen. •...
Page 67
G Configuring the HTTP port number 1) Enter the HTTP port number in “HTTP Port Number” (default: 80). • For most applications, select 80 (default: 80). 2) Click the “Change” button. G DNS update to DNS 1/2 Server When you set a domain name (FQDN) for the camera, you can access the camera with the domain name.
Page 68
Mail Settings You can configure the camera to send an email up to 10 addresses when any motions are detected. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “Mail”...
Page 69
“Receiver email address 10.” 6) Click the “Save Settings” button. 7) Enter the mail title in “Subject” (default: TOSHIBA Network Camera). If a check is added to “Camera Name automatically,” the camera name is set automatically as the subject.
Page 70
FTP Client Settings You can store images on an FTP server. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “FTP client” on the left side of the screen. •...
Page 71
DDNS Settings You can utilize the DDNS. Configure the connection for a DDNS server. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “DDNS” on the left side of the screen. •...
Download the latest firmware. G Create a folder where you want to save the latest firmware. G Access to the following Toshiba Web page on the Internet. URL: http://www.netcam.toshiba.com G Download the latest firmware according to the instructions on the Web page.
Click “Firmware update.” • The Firmware update screen appears on the right side of the display. Click the “Browse” button. • A screen appears, allowing you to select a file. Select the file of the latest firmware you downloaded in the above “Before Starting”...
Saving the Settings on a Personal Computer You can save the settings of the network camera on a personal computer. Click “Configuration” on the left side of the “Camera Window” screen. • The Configuration menu appears on the left side of the screen. Click “System”...
Importing the Settings Saved on a Personal Computer Click “Import new configurations” on the System setting screen. • The Import new configuration screen appears on the right side of the display. Click the “Browse” button. • A screen appears, allowing you to select a file. Select the file on settings you saved.
Others Index (Glossary) Display of Logs Before Calling Service Personnel... Specifications Appearance Diagram...
Page 78
Index (Glossary) AC IN ... 6 Accessories ... Safety Precautions3 Adjust the date and time ... 58 Administrator ... 26 AES ... 18 Alarm settings ... 64 Attaching picture to mail ... 69 AVI ... 52 AWB ... 19 Back light compensation (BLC) ... 18 Before calling service personnel ...
Page 79
Hub ... 22 Wire gathering device used in10Base-T/ 100Base-TX network. Build up a network by connecting devices around a hub radially. There are various ports, like 8port, 4port. IP address ... 21 Address information for IP protocol. All devices communicate with IP must have IP addresses.
Page 80
TCP/IP. Updating firmware ... 72 URL ... 23 (Uniform Resource Locator) Method for assigning the Internet resource. “http://www.toshiba. com/” is the example of when accessing a website on the Internet. VIDEO OUT ... 6 Video output ... 6 Wall bracket ...
Page 81
Display of Logs Display System Boot Change Quality Change resolution Change Brightness Change Contrast Change Saturation Change Hue Set Flickerless Change Area(BLC) Camera Name Set Time Type Set Text Color Change Camera Time Set Daylight Saving Upload IPCamera Set User check Add User Delete User Change Admin...
Page 82
Display of Logs (Cont.) Display Set DDNS Set Motion Record FTP down:re-connect FTP Client storage path isn't exist FTP binary mode change fail Mail connect Mail connect fail Send e-mail finish NTP connect fail New client FTP fail to write image Description The DDNS setting is configured The recording at the time of motion detection is set...
Page 83
Before Calling Service Personnel... Symptom Cause GThe power of the camera There is no IP address of your is not turned on. network camera GLAN cable is not on The Camera Finder’s Network connected. Camera List. GLAN cable is not connected to the PC.
Page 84
Before Calling Service Personnel... (Cont.) Symptom GEntering wrong login ID Error message shows up when and password. trying to login. GCapsLock of the PC is GYou forget your login ID and the password. GDefault gateway is not Cannot access to the camera from configured.
Page 85
Symptom Cause GLost the power of the Cannot perform settings. camera during the performance. GLAN cable of the camera has been pulled off during the performance. GLAN cable of the PC has been pulled off during the performance. GLost the power of a hub or router during the performance.
Page 86
GWhen many users access to the camera at the same time, the renewal speed of the image becomes slow. GMake sure that the camera is installed in right way. Adjust the setting to place the “Toshiba” logo in the right direction.
Page 87
Symptom Cause GMonitor color setting of Colors of the images are poor. your PC is set to 16 bit or less. GThe lens cover of the Focus of the images is poor. camera is not clean, or some dusts are on it. GDistance to an object is too close.
Page 88
Before Calling Service Personnel... (Cont.) Symptom GFTP recording function is Recorded images are not not set to ON. saved in FTP GIP address of the FTP server. server, ID/ password or transfer directory is not set properly. GCould not keep the communication with the server during file transfer using FTP.
Page 89
About PoE Power Supply Function for Supplying Power via a LAN Cable • There are two PoE (Power Over Ethernet) methods: the Spare Pair method (a power supply method that uses the unused wires) and the Signal Pair method (a power supply method that uses the signal wires).
Page 90
Designs and specifications may change without prior notice for better improvement. Some screen displays, pictures and illustrations contained herein may slightly differ from the actual images. IK-WR01A AC 24V 10% 60Hz/DC 12V 10%/ PoE 5.5w 1/3 inch CCD image area sensor 4.96mm (0.195inch) horizontal X 6.0mm...
Page 91
Appearance Diagram unit : mm (inches) 48.5 (1.91) 110 (4.33) 155 (6.10)
Page 92
Appearance Diagram (Cont.) unit : mm (inches) 150 (5.91) 61.5 (2.42) 41 (1.61) 147.5 (5.81)
Page 93
I Bracket unit : mm (inches) 120 (4.72) 46 (1.81) 4-M4 φ φ I Mounting Base 85 (3.35) 46 (1.81) 4.4 (0.17) φ 4-M6 Depth=10 φ φ 15(0.59) 40(1.57) 15(0.59) 55(2.17)
Page 94
TOSHIBA AMERICA INFORMATION SYSTEMS. INC Security & Network Video Products 9740 Irvine Boulevard, Irvine California 92618-1697 Phone Number: (877)696-3822...