Technical Data; Intended Use; General Power Tool Safety Warnings - Black & Decker HD450 Original Instructions Manual

HAMMER DRILL
HD400/ HD450/ HD500

Technical Data

Specifications:
Voltage V
ac
Hz
Power input W
No-load speed min
-1
Max drill capacity
Steel/Concrete mm
Wood mm mm
DO NOT RETURN THIS PRODUCT TO THE STORE, first
contact your local Black & Decker office or nearest authorized
service center.

INTENDED USE

Your Black & Decker hammer drill has been designed for drilling
in wood, metal, plastics, and masonry as well as for screwdriving
purposes.
SAVE THESE INSTRUCTIONS

General power tool safety warnings

Warning! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in all of the warnings listed below refers
to your mains operated (corded) power tool or battery operated
(cordless) power tool.
1. Work Area Safety
a. Keep work area clean and well lit. Cluttered and
dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids,
gases or dust. Power tools create sparks which may
ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
2. Electrical Safety
a. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
HD400 HD450
220-240V~ 220-240V~
50/60Hz 50/60Hz
500 500
3000 0-3000
10 10
20 20
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
HD500
Keep cord away from heat, oil, sharp edges or
220-240V~
moving parts. Damaged or entangled cords increase
50/60Hz
the risk of electric shock.
550
e. When operating a power tool outdoors, use an
0-3000
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
13
electric shock.
20
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock. Note: The term "Residual Curent Device
(RCD)" can be replaced by "Ground Fault Circuit
Interrupter (GFCI)" or by "Earth Leakage Circuit
Breaker (ELCB)".
3. Personal Safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury.
b. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
d. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
e. Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices
can reduce dust related hazards.