Sealey BT2012.V2 Instructions

thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
refer to Wear eye
instructions protection
1. safety
1.1. personal preCaUtions
ensure that there is another person within hearing range and close enough to come to your aid, should a problem arise when working near
9
a lead-acid battery.
Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.
9
Have fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.
9
Wash immediately with soap and water if battery acid contacts skin or clothing. if acid enters eye, flush eye immediately with cool, clean
9
running water for at least 15 minutes and seek immediate medical attention.
remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current
9
which is high enough to weld such items to the vehicle and cause severe burns.
ensure that hands, clothing (especially belts) are clear of fan blades and other moving or hot parts of engine. remove ties and contain
9
long hair.
do not smoke or allow a spark or flame in the vicinity of the battery or engine.
8
1.2. general safety instrUCtions
familiarise yourself with the application, limitations and potential hazards of the tester. Also refer to the vehicle manufacturer's hand book.
9
if in AnY douBt consult A QuAlified electriciAn.
ensure that the tester is in good condition before use. if in any doubt do not use the unit and contact a qualified electrician.
9
only use recommended attachments and parts. to use unapproved items may be dangerous and will invalidate your warranty.
9
Keep tools and other items away from the engine and ensure that you can see the battery and working parts of the engine clearly.
9
determine the system voltage before using the tester.
9
if the tester receives a sharp knock or blow the unit must be checked by a qualified service agent before using.
9
if the battery terminals are corroded or dirty: clean them before using the tester.
9
Keep children and unauthorised persons away from the work area.
9
do not dismantle the tester for any reason. the tester must only be checked by qualified service personnel.
8
warning! to prevent the risk of sparking, short circuit and possible explosion do not drop metal tools in the battery area, or allow them
‰
to touch the battery terminals.
do not cross-connect tester to battery. ensure positive (red) clamp is to positive terminal and negative (BlAcK) clamp is to negative
8
terminal. if battery symbols cannot be distinguished: the negative terminal is the one directly connected to the vehicle bodywork.
do not use the tester outdoors, or in damp, or wet locations and do not use in the vicinity of flammable liquids or gases.
8
ensure there is effective ventilation to prevent a build-up of explosive gases.
8
do not use the tester for a task for which it is not designed.
8
When not in use, store the tester carefully in a safe, dry, childproof location.
9
2. introdUCtion
fast and accurate diagnosis of battery and alternator faults with facility to print the results. large lcd display shows charging and starting
system status and returns decision making information in seconds. results need no interpretation and the tester will work on batteries with as
little as 1.5V of residual charge.

3. speCifiCation

Model no: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .bt2012.V2
rated battery Voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V
rating systems: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . din, en, iec, sAe
test range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-1400 cold cranking Amps
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-800 ccA* din
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-1400 ccA* en
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-800 ccA* iec
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50-1400 ccA* sAe
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .By Battery type Jis
Voltage range: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5-17V
replacement Printer rolls: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bt2003.V2-01 (Pack of 2)
Battery: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 x 9V (not supplied)
© Jack sealey limited
instructions for
digital battery & alternator tester
with printer 12V
model no:
Warning
corrosive
substance
Original Language Version
bt2012.V2
Bt2012.V2 | issue 4 (3) 17/01/18