Sealey SA57 Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
 WARNING! Disconnect from air supply before changing accessories or servicing.
 WARNING! Check correct air pressure is maintained and not exceeded.
We recommend 90psi.
 WARNING! DO NOT use screwdriver if damaged or faulty. Contact your local service agent.
 DO NOT use the screwdriver for a task it is not designed to perform.
 DO NOT hold the workpiece by hand. Use clamps or a vice to secure the workpiece.
 DO NOT use screwdriver unless you have been instructed in its use by a qualified person.
 DO NOT drop, throw or abuse the screwdriver.
 DO NOT carry the screwdriver by the air hose, or yank the hose from the air supply.
 DO NOT operate screwdriver if you are tired or under the influence of alcohol, drugs or intoxicating medication.
 DO NOT carry screwdriver with your hand on the power trigger in order to avoid unintentional starting.
 DO NOT direct air from the air hose at yourself or others.
 Follow all workshop Health & Safety rules, regulations, and conditions when using screwdriver.
 Maintain screwdriver in good condition and replace any damaged or worn parts.
Use genuine parts only.
Unauthorised parts may be dangerous and will invalidate the warranty.
 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
 Keep screwdriver bits clean and in good condition for best and safest performance.
 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
 Secure unstable work-piece with a clamp, vice or other adequate holding device.
 Keep children and unauthorised persons away from the working area.
 Ensure the screwdriver bit is secure in the chuck.
 Wear approved safety eye and ear protection.
 Avoid unintentional starting.
 When not in use disconnect from air supply and store in a safe, dry, childproof location.
 WARNING! The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions
and situations that may occur. It must be understood that common sense and caution are factors which cannot be built into this
product, but must be applied by the operator.
2. INTRODUCTION
Fully polished, machined, aluminium body. Features three speed settings with forward/reverse control and quick release bit mechanism. Ideal
for assembly/dismantling and general production work. Suitable for use with AK2050 Power Tool Bit Set.
3. SPECIFICATION
Model No: . . . . . . . . . . . . . . . . . . SA57
Chuck size . . 6mm Hex Quick-Release
Free speed . . . . . . . . . . . . . . . 9800rpm
Air consumption . . . . . . . . . . . . . . 4cfm
Operating pressure. . . . . . . . . . . . 90psi
Air Inlet Size: . . . . . . . . . . . . . . 1/4"BSP
Weight: . . . . . . . . . . . . . . . . . . . . . 0.8kg
Noise Power: . . . . . . . . . . . . . .103.2dB
4. PREPARATION
3.1. Air Supply.
Recommended hook-up procedure is shown in fig.1.
3.1.1. Ensure tool valve (or trigger) is in the "off" position before connecting to the air supply.
3.1.2. You will require an air pressure of 90psi, and an air flow according to specification.
3.1.3. WARNING! Ensure the air supply is clean and does not exceed 90psi while operating the tool. Too high an air pressure and/or unclean
air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
3.1.4. Drain the air tank daily. Water in the air line will damage the tool.
3.1.5. Clean air inlet filter weekly.
3.1.6. Line pressure should be increased to compensate for unusually long air hoses (over 8 meters). The minimum hose diameter should be
1/4" I.D. and fittings must have the same inside dimensions.
3.1.7. Keep hose away from heat, oil and sharp edges. Check hose for wear, and make certain that all connections are secure.
3.2. Couplings.
Vibration may cause failure if a quick change coupling is connected directly to the tool. To overcome this, connect a leader hose to the tool. A
quick change coupling may then be used to connect the leader hose to the air line recoil hose. See fig.1 & 2.
© Jack Sealey Limited
INSTRUCTIONS FOR:
AIR STRAIGHT REVERSABLE SCREWDRIVER
MODEL NO:
Noise Pressure: . . . . . . . . . . . . .92.2dB
Vibration: . . . . . . . . . . . . . . . . 0.76m/s²
Uncertainty: . . . . . . . . . . . . . . 0.38m/s²
Original Language Version
SA57
SA57 Issue:3 (SP) - 06/08/14